ASTM F3541-22
(Practice)Standard Practice for Sectional Repair of Existing Gravity Flow, Non-Pressure Pipelines and Conduits by Pushed or Pulled-In-Place Installation of Cured-In-Place Thermosetting Resin Pipe (CIPP)
Standard Practice for Sectional Repair of Existing Gravity Flow, Non-Pressure Pipelines and Conduits by Pushed or Pulled-In-Place Installation of Cured-In-Place Thermosetting Resin Pipe (CIPP)
SIGNIFICANCE AND USE
4.1 This practice is for use by designers and specifiers, regulatory agencies, owners, and inspection organizations who are involved in the rehabilitation of gravity flow, non-pressure pipes through the use of a resin-saturated liner installed within a section of damaged or leaking existing pipe. As for any practice, modifications may be required for specific job conditions.
SCOPE
1.1 This practice describes the procedures for the sectional repair of gravity flow, non-pressure pipelines and conduits 3 in. to 60 in. (75 mm to 1500 mm) diameter by the installation of a resin-saturated liner which is placed onto or wrapped around a carrier device, pushed or pulled into an existing pipeline or conduit and expanded against the interior of the host pipe or conduit with air pressure. The resin is cured under ambient conditions, by photoinitiated reaction or with the application of heat. When cured, the finished sectional repair will be tight-fitting across its installed length. This repair process is used in a variety of gravity flow, non-pressure applications such as sanitary sewers, storm sewers, drains, electrical conduits and ventilation systems.
1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F3541 − 22
Standard Practice for
Sectional Repair of Existing Gravity Flow, Non-Pressure
Pipelines and Conduits by Pushed or Pulled-In-Place
Installation of Cured-In-Place Thermosetting Resin Pipe
1
(CIPP)
This standard is issued under the fixed designation F3541; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This practice describes the procedures for the sectional
2.1 ASTM Standards:
repairofgravityflow,non-pressurepipelinesandconduits3in.
D543Practices for Evaluating the Resistance of Plastics to
to 60in. (75mm to 1500 mm) diameter by the installation of a
Chemical Reagents
resin-saturated liner which is placed onto or wrapped around a
D578/D578MSpecification for Glass Fiber Strands
carrier device, pushed or pulled into an existing pipeline or
D790Test Methods for Flexural Properties of Unreinforced
conduit and expanded against the interior of the host pipe or
and Reinforced Plastics and Electrical Insulating Materi-
conduit with air pressure. The resin is cured under ambient
als
conditions,byphotoinitiatedreactionorwiththeapplicationof
D1600TerminologyforAbbreviatedTermsRelatingtoPlas-
heat. When cured, the finished sectional repair will be tight-
tics
fitting across its installed length. This repair process is used in
D3567PracticeforDeterminingDimensionsof“Fiberglass”
a variety of gravity flow, non-pressure applications such as
(Glass-Fiber-Reinforced Thermosetting Resin) Pipe and
sanitary sewers, storm sewers, drains, electrical conduits and
Fittings
ventilation systems.
D5813 Specification for Cured-In-Place Thermosetting
1.2 Units—The values stated in inch-pound units are to be
Resin Sewer Piping Systems
regarded as standard. The values given in parentheses are
F412Terminology Relating to Plastic Piping Systems
mathematical conversions to SI units that are provided for
F1216Practice for Rehabilitation of Existing Pipelines and
information only and are not considered standard.
Conduits by the Inversion and Curing of a Resin-
1.3 This standard does not purport to address all of the
Impregnated Tube
safety concerns, if any, associated with its use. It is the
F2019Practice for Rehabilitation of Existing Pipelines and
responsibility of the user of this standard to establish appro-
Conduits by the Pulled in Place Installation of Glass
priate safety, health, and environmental practices and deter-
Reinforced Plastic Cured-in-Place (GRP-CIPP) Using the
mine the applicability of regulatory limitations prior to use.
UV-Light Curing Method
1.4 This international standard was developed in accor-
3
dance with internationally recognized principles on standard-
2.2 ASCE Standard:
ization established in the Decision on Principles for the
Manual of Practice 145,Design of Close-Fit Liners for the
Development of International Standards, Guides and Recom-
Rehabilitation of Gravity Pipes
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This test method is under the jurisdiction ofASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.67 on Standards volume information, refer to the standard’s Document Summary page on
Trenchless Plastic Pipeline Technology. the ASTM website.
3
Current edition approved Sept. 1, 2022. Published September 2022. DOI: Available fromAmerican Society of Civil Engineers (ASCE), 1801Alexander
10.1520/F3541–22 Bell Dr., Reston, VA 20191, http://www.asce.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F3541 − 22
4
2.3 ISO Standard: 3.2.11 release agent, n—Anon-reactive,sacrificialchemical
ISO 11296-4, Plastics piping systems for renovation of applied to a surface to prevent bonding.
underground non-pressure drainage and sewerage net-
3.2.12 tight-fitting, adj—conformance of a lining system to
works — Part 4: Lining with cured-in-place pipes
the host pipe interior geometry whereas intimate contact is
5
2.4 NSF Standard:
realized across the entire perimeter.
NSF/ANSI-14, SE10990 – Rehabilitation by Point Repair
3.2.13 wellpoint system, n—A series of closely spaced,
of Existing Pipe
small diameter, shallow wells connected to a comm
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.