ASTM D6154-09
(Specification)Standard Specification for Chemically Modified Asphalt Cement for Use in Pavement Construction
Standard Specification for Chemically Modified Asphalt Cement for Use in Pavement Construction
ABSTRACT
This specification covers asphalt cements that have been modified by the addition of a chemical gellant. The asphalt cement used to prepare the chemically modified asphalt cement shall be prepared by the refining of crude petroleum by suitable methods. Chemically modified asphalt cements are normally produced by addition of a chemical stabilizer. However, any asphalt modifier may be used that will give the required test results when blended with the desired asphalt. Different test methods shall be performed in order to determine the following properties of the cement: penetration, viscosity, flash point using Cleveland open cup, solubility in trichloroethylene, softening point, residue from thin-film oven test.
SCOPE
1.1 This specification covers asphalt cements that have been modified by the addition of a chemical gellant. It was developed to provide a reference for specifying chemically modified asphalt cement and reflects the properties of currently available commercial products. The tests are intended to measure degree of modification not performance characteristics. This is not intended to be a performance–based specification.
1.2 Chemically modified asphalt cements are normally produced by addition of a chemical stabilizer. However, any asphalt modifier may be used that will give the required test results when blended with the desired asphalt.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 The following precautionary statement pertains to the test method portion only, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D6154 −09
StandardSpecification for
Chemically Modified Asphalt Cement for Use in Pavement
1
Construction
This standard is issued under the fixed designation D6154; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D92 Test Method for Flash and Fire Points by Cleveland
Open Cup Tester
1.1 This specification covers asphalt cements that have been
D140 Practice for Sampling Bituminous Materials
modified by the addition of a chemical gellant. It was devel-
D1754 Test Method for Effects of Heat andAir onAsphaltic
oped to provide a reference for specifying chemically modified
Materials (Thin-Film Oven Test)
asphalt cement and reflects the properties of currently available
D2042 Test Method for Solubility of Asphalt Materials in
commercial products. The tests are intended to measure degree
Trichloroethylene
of modification not performance characteristics. This is not
D4957 Test Method forApparentViscosity ofAsphalt Emul-
intended to be a performance–based specification.
sion Residues and Non-Newtonian Bitumens by Vacuum
1.2 Chemically modified asphalt cements are normally pro-
Capillary Viscometer
duced by addition of a chemical stabilizer. However, any
3. Materials and Manufacture
asphalt modifier may be used that will give the required test
results when blended with the desired asphalt.
3.1 The asphalt cement used to prepare the chemically
modified asphalt cement shall be prepared by the refining of
1.3 The values stated in SI units are to be regarded as
crude petroleum by suitable methods.
standard. No other units of measurement are included in this
standard.
4. Physical Properties
1.4 The following precautionary statement pertains to the
4.1 The chemically modified asphalt cement shall be
test method portion only, Section 5, of this specification: This
homogeneous,freefromwater,andshallnotfoamwhenheated
standard does not purport to address all of the safety concerns,
to 180°C.
if any, associated with its use. It is the responsibility of the user
4.2 The chemically modified asphalt cement shall conform
of this standard to establish appropriate safety and health
to the requirements of Table 1.
practices and determine the applicability of regulatory limita-
tions prior to use.
5. Methods of Sampling and Testing
5.1 Sample and test the chemically modified asphalt cement
2. Referenced Documents
in accordance with the following methods:
2
2.1 ASTM Standards:
5.1.1 Sampling—See Practice D140.
D5 Test Method for Penetration of Bituminous Materials
5.1.2 Penetration—See Test Method D5.
D36 Test Method for Softening Point of Bitumen (Ring-and-
5.1.3 Viscosity at 60°C—See Test Method D4957.
Ball Apparatus)
5.1.4 Viscosity at 135°C—See Test Method D4957.
5.1.5 Flash Point, Cleveland Open Cup—See Test Method
D92.
1
This specification is under the jurisdiction of ASTM Committee D04 on Road
5.1.6 Solubility in Trichloroethylene—See Test Method
and Paving Materials and is the direct responsibility of Subcommittee D04.40 on
D2042.
Asphalt Specifications.
5.1.7 Softening Point—See Test Method D36.
Current edition
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D6154–04 Designation: D 6154 – 09
Standard Specification for
Chemically Modified Asphalt Cement for Use in Pavement
1
Construction
This standard is issued under the fixed designation D 6154; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers asphalt cements that have been modified by the addition of a chemical gellant. It was developed
to provide a reference for specifying chemically modified asphalt cement and reflects the properties of currently available
commercial products. The tests are intended to measure degree of modification not performance characteristics. This is not
intended to be a performance–based specification.
1.2 Chemically modified asphalt cements are normally produced by addition of a chemical stabilizer. However, any asphalt
modifier may be used that will give the required test results when blended with the desired asphalt.
1.3The values stated in SI units are to be regarded as the standard.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 The following precautionary statement pertains to the test method portion only, Section 5, of this specification: This
standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D5 Test Method for Penetration of Bituminous Materials
D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester
D 140 Practice for Sampling Bituminous Materials
D 1754 Test Method for Effects of Heat and Air on Asphaltic Materials (Thin-Film Oven Test)
D 2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene
D 4957 Test Method forApparentViscosity ofAsphalt Emulsion Residues and Non-Newtonian Bitumens byVacuum Capillary
Viscometer
3. Materials and Manufacture
3.1 The asphalt cement used to prepare the chemically modified asphalt cement shall be prepared by the refining of crude
petroleum by suitable methods.
4. Physical Properties
4.1 The chemically modified asphalt cement shall be homogeneous, free from water, and shall not foam when heated to 180°C.
4.2 The chemically modified asphalt cement shall conform to the requirements of Table 1.
5. Methods of Sampling and Testing
5.1 Sample and test the chemically modified asphalt cement in accordance with the following methods:
5.1.1 Sampling—See Practice D 140.
5.1.2 Penetration— See Test Method D 5.
5.1.3 Viscosity at 60°C—See Test Method D 4957.
1
This specification is under the jurisdiction ofASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.40 onAsphalt
Specifications.
Current edition approved June 1, 2004.2009. Published June 2004.2009. Originally approved in 1997. L
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.