ASTM B775/B775M-16

Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe

ABSTRACT
This general specification contains the mandatory requirements to the ASTM standards listed herein for longitudinally welded piping made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.
SCOPE
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:2    
Title of Specification  
ASTM
Designation2  
Welded UNS N08020 Alloy Pipe  
B464/B464M  
Welded Nickel-Iron-Chromium Alloy Pipe  
B514  
Welded Nickel-Chromium-Iron-Alloy (UNS N06600,
UNS N06603, UNS N06025 and UNS N06045) Pipe  
B517  
Welded Nickel and Nickel-Cobalt Alloy Pipe  
B619/B619M  
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe  
B673  
UNS N08367 Welded Pipe  
B675  
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded Pipe  
B705  
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe  
B723  
Welded Nickel (UNS N02200/UNS N02201) and Nickel
Copper Alloy (UNS N04400) Pipe  
B725  
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.  
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Apr-2016
• ICS: 77.150.40 - Nickel and chromium products
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B775-15 - Standard Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe
• Effective Date: 01-May-2016

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:B775/B775M −16
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775/B775M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* responsibility of the user of this standard to become familiar
with all hazards including those identified in the appropriate
1.1 This specification contains various requirements that,
Safety Data Sheet (SDS) for this product/material as provided
with the exception of Section 5 and Section 10, are mandatory
by the manufacturer, to establish appropriate safety and health
requirements to the following ASTM nickel and nickel alloy,
2 practices, and determine the applicability of regulatory limi-
longitudinally welded piping specifications:
tations prior to use.
ASTM
2
Title of Specification Designation
2. Referenced Documents
2
Welded UNS N08020 Alloy Pipe B464/B464M
2.1 ASTM Standards:
Welded Nickel-Iron-Chromium Alloy Pipe B514
B168 Specification for Nickel-Chromium-Iron Alloys (UNS
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
N06600, N06601, N06603, N06690, N06693, N06025,
UNS N06603, UNS N06025 and UNS N06045) Pipe
Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M
N06045, and N06696), Nickel-Chromium-Cobalt-
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673
Molybdenum Alloy (UNS N06617), and Nickel-Iron-
UNS N08367 Welded Pipe B675
Chromium-Tungsten Alloy (UNS N06674) Plate, Sheet,
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
Pipe
and Strip
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723
B464/B464M Specification for Welded UNS N08020 Alloy
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Copper Alloy (UNS N04400) Pipe Pipe
B514 SpecificationforWeldedNickel-Iron-ChromiumAlloy
1.2 One or more of the test requirements of Section 5 apply
Pipe
only if specifically stated in the product specification or in the
B517 Specification for Welded Nickel-Chromium-Iron-
purchase order.
Alloy (UNS N06600, UNS N06603, UNS N06025, and
1.3 In case of conflict between a requirement of the product
UNS N06045) Pipe
specification and a requirement of this general specification,
B619/B619M Specification for Welded Nickel and Nickel-
only the requirement of the product specification needs to be
Cobalt Alloy Pipe
satisfied.
B673 Specification for UNS N08925, UNS N08354, and
1.4 The values stated in either SI units or inch-pound units
UNS N08926 Welded Pipe
are to be regarded separately as standard. The values stated in
B675 Specification for UNS N08367 Welded Pipe
each system may not be exact equivalents; therefore, each
B705 SpecificationforNickel-Alloy(UNSN06625,N06219
system shall be used independently of the other. Combining
and N08825) Welded Pipe
values from the two systems may result in non-conformance
B723 Specification for Nickel-Chromium-Molybdenum-
with the standard.
Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333)
Welded Pipe
1.5 This standard does not purport to address all of the
B725 Specification for Welded Nickel (UNS N02200/UNS
safety concerns, if any, associated with its use. It is the
N02201) and Nickel Copper Alloy (UNS N04400) Pipe
B880 Specification for General Requirements for Chemical
1
This specification is under the jurisdiction of ASTM Committee B02 on
Check Analysis Limits for Nickel, Nickel Alloys and
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
Cobalt Alloys
B02.07 on Refined Nickel and Cobalt and Their Alloys.
B899 Terminology Relating to Non-ferrous Metals and Al-
Current edition approved May 1, 2016. Published June 2016. Originally
loys
approved in 1987. Last previous edition approved in 2015 as B775 – 15. DOI:
10.1520/B0775_B0775M-16.
E8 Test Methods for Tension Testing of Metallic Materials
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
E18 Test Methods for Rockwell Hardness of Metallic Ma-
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
terials
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. E29 Practice for Using Significant Digits in Test Data to
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B775/B775M−16
Determine Conformance with Specifications 4.2 The ladle analysis of the material shall conform to the
E39 Methods for Chemical Analysis of Nickel (Withdrawn chemical requirements prescribed by the individual
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: B775 − 15 B775/B775M − 16
Standard Specification for
General Requirements for Nickel and Nickel Alloy Welded
1
Pipe
This standard is issued under the fixed designation B775;B775/B775M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification contains various requirements that, with the exception of Section 5 and Section 10, are mandatory
2
requirements to the following ASTM nickel and nickel alloy, longitudinally welded piping specifications:
ASTM
2
Title of Specification Designation
Welded UNS N08020, N08024, and N08026 Alloy Pipe B464/B464M
Welded UNS N08020 Alloy Pipe B464/B464M
Welded Nickel-Iron-Chromium Alloy Pipe B514
Welded Nickel-Chromium-Iron-Alloy (UNS N06600, B517
UNS N06603, UNS N06025 and UNS N06045) Pipe
Welded Nickel and Nickel-Cobalt Alloy Pipe B619/B619M
UNS N08904, UNS N08925, and UNS N08926 Welded Pipe B673
UNS N08367 Welded Pipe B675
Nickel-Alloy (UNS N06625, N06219, and N08825) Welded B705
Pipe
Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Welded Pipe B723
Welded Nickel (UNS N02200/UNS N02201) and Nickel B725
Copper Alloy (UNS N04400) Pipe
1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the
purchase order.
1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only
the requirement of the product specification needs to be satisfied.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values given in
parentheses are mathematical conversions to SI units that are provided for information only and are not considered stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet
(SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and
determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
B168 Specification for Nickel-Chromium-Iron Alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045,
and N06696), Nickel-Chromium-Cobalt-Molybdenum Alloy (UNS N06617), and Nickel-Iron-Chromium-Tungsten Alloy
(UNS N06674) Plate, Sheet, and Strip
B464/B464M Specification for Welded UNS N08020 Alloy Pipe
B514 Specification for Welded Nickel-Iron-Chromium Alloy Pipe
1
This specification is under the jurisdiction of ASTM Committee B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on Refined
Nickel and Cobalt and Their Alloys.
Current edition approved Oct. 1, 2015May 1, 2016. Published December 2015June 2016. Originally approved in 1987. Last previous edition approved in 20132015 as
B775 – 13.B775 – 15. DOI: 10.1520/B0775-15.10.1520/B0775_B0775M-16.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
B775/B775M − 16
B517 Specification for Welded Nickel-Chromium-Iron-Alloy (UNS N06600, UNS N06603, UNS N06025, and UNS N06045)
Pipe
B619/B619M Specification for Welded Nickel and Nickel-Cobalt Alloy Pipe
B673 Specification for UNS N08925, UNS N08354, and UNS N08926 Welded Pipe
B675 Specification for UNS N08367 Welded Pipe
B705 Specification for Nickel-Alloy (UNS N06625, N06219 and N08825) Welded Pipe
B723 Specification for Nickel-Chromium-Molybdenum-Cobalt-Tungsten-Iron-Silicon Alloy (UNS N06333) Welded Pipe
B725 Specification for Welded Nickel (UNS N02200/UNS N02201) and Nickel Copper Alloy (UNS N04400) Pipe
B880 Specification for Genera
...