ASTM C1767-13a
(Specification)Standard Specification for Stainless Steel Jacketing for Insulation
Standard Specification for Stainless Steel Jacketing for Insulation
ABSTRACT
This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems. While not intended to cover use inside the containment buildings of nuclear power plants, this specification does not preclude use of Class E material which does not have a moisture barrier in this containment building application. This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation.
SCOPE
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude use of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of stainless steel jacketing, see (1).2
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1767 −13a
StandardSpecification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
3
2.1 ASTM Standards:
1.1 This specification covers stainless steel jacketing for
A167 Specification for Stainless and Heat-Resisting
thermal, acoustical, and fire protective insulation operating at
Chromium-Nickel Steel Plate, Sheet, and Strip
either above or below ambient temperatures and in both indoor
A240/A240M Specification for Chromium and Chromium-
and outdoor locations. It does not cover insulation jacketing
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
made from other materials such as mastics, fiber reinforced
Vessels and for General Applications
plastic, PVC, aluminum, or coated carbon steel (for example,
A480/A480M Specification for General Requirements for
aluminum-zinc, galvanized steel, or aluminized steel) nor does
Flat-Rolled Stainless and Heat-Resisting Steel Plate,
it cover the details of thermal, acoustical, or fire protective
Sheet, and Strip
insulation systems.
C168 Terminology Relating to Thermal Insulation
C450 Practice for Fabrication of Thermal Insulating Fitting
1.2 While not intended to cover use inside the containment
Covers for NPS Piping, and Vessel Lagging
buildings of nuclear power plants, this standard does not
C585 Practice for Inner and Outer Diameters of Thermal
preclude use of Class E material which does not have a
Insulation for Nominal Sizes of Pipe and Tubing
moisture barrier in this containment building application.
C835 Test Method for Total Hemispherical Emittance of
1.3 This specification provides physical requirements for
Surfaces up to 1400°C
stainless steel jacketing for thermal and acoustical insulation. C1371 Test Method for Determination of Emittance of
Guide C1423 provides guidance in selecting jacketing materi- Materials Near Room Temperature Using Portable Emis-
someters
als and their safe use.
C1423 Guide for Selecting Jacketing Materials for Thermal
1.4 This is a material specification and does not imply any
Insulation
performance of the installed system using the materials speci-
C1729 Specification for Aluminum Jacketing for Insulation
fied herein. For information about installation of stainless steel
E84 Test Method for Surface Burning Characteristics of
2
jacketing, see (1).
Building Materials
F1249 Test Method for Water Vapor Transmission Rate
1.5 The values stated in inch-pound units are to be regarded
Through Plastic Film and Sheeting Using a Modulated
as standard. The values given in parentheses are mathematical
Infrared Sensor
conversions to SI units that are provided for information only
and are not considered standard.
3. Terminology
1.6 This standard does not purport to address all of the
3.1 Definitions—Definitions in Terminology C168 apply to
safety concerns, if any, associated with its use. It is the
terms used in this specification.
responsibility of the user of this standard to establish appro-
3.2 Definitions of Terms Specific to This Standard:
priate safety and health practices and determine the applica-
3.2.1 box rib—stainless steel sheet formed to have alternat-
bility of regulatory limitations prior to use.
ing parallel grooves and ridges with a cross section approxi-
mating a square wave.
3.2.2 cladding (as related to insulation jacketing)—
1
ThistestmethodisunderthejurisdictionofASTMCommitteeC16onThermal
synonymous with jacketing.
Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation
Systems.
Current edition approved Sept. 1, 2013. Published October 2013. Originally
3
approved in 2012. Last previous edition approved in 2013 as C1767–13. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/C1767-13A. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
2
The boldface numbers in parentheses refer to the list of references at the end of Standards volume information, refer to the standard’s Document Summary page on
this standard. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1767−13a
3.2.2.1 Discussion—The three terms “jacketing”, “lagging”, 3.2.13.1 Discussion—the fold is typically made toward the
and “cladding” are considered synonymous in most applica- underside of the jacketing so that the original edge is hidden
tions and geographies. However, in some cases in the pow
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1767 − 13 C1767 − 13a
Standard Specification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either
above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from
other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc,
galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude
use of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide
C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified
2
herein. For information about installation of stainless steel jacketing, see (1).
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
C168 Terminology Relating to Thermal Insulation
C450 Practice for Fabrication of Thermal Insulating Fitting Covers for NPS Piping, and Vessel Lagging
C585 Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
C835 Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C
C1371 Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
C1423 Guide for Selecting Jacketing Materials for Thermal Insulation
C1729 Specification for Aluminum Jacketing for Insulation
E84 Test Method for Surface Burning Characteristics of Building Materials
F1249 Test Method for Water Vapor Transmission Rate Through Plastic Film and Sheeting Using a Modulated Infrared Sensor
3. Terminology
3.1 Definitions—Definitions in Terminology C168 apply to terms used in this specification.
3.2 Definitions of Terms Specific to This Standard:
1
This test method is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation Systems.
Current edition approved May 1, 2013Sept. 1, 2013. Published June 2013October 2013. Originally approved in 2012. Last previous edition approved in 20122013 as
C1767–12.–13. DOI: 10.1520/C1767-13.10.1520/C1767-13A.
2
The boldface numbers in parentheses refer to the list of references at the end of this standard.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1767 − 13a
3.2.1 box rib—stainless steel sheet formed to have alternating parallel grooves and ridges with a cross section approximating
a square wave.
3.2.2 cladding (as related to insulat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.