ASTM F2281-03

Standard Specification for Stainless Steel and Nickel Alloy Bolts, Hex Cap Screws, and Studs, for Heat Resistance and High Temperature Applications

SCOPE
1.1 This specification covers the chemical and mechanical requirements for stainless steel and nickel alloy bolts, hex cap screws, and studs, 1/4 in. diameter and larger, intended for use at temperatures up to 1800°F (982°C), and in applications where resistance to heat and the effects of high temperature are to be considered. See Appendix X1 for Service Application. A wide variety of materials are covered in this specification which can be used at high temperatures as a function of the specific alloy properties, as well as environmental requirements including corrosive environments.
1.2 The values stated in inch-pound units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

General Information

• Status: Historical
• Publication Date: 09-Jun-2003
• ICS: 21.060.10 - Bolts, screws, studs
• Technical Committee: F16 - Fasteners
• Drafting Committee: F16.04 - Nonferrous Fasteners

Relations

• Replaced By: ASTM F2281-04 - Standard Specification for Stainless Steel and Nickel Alloy Bolts, Hex Cap Screws, and Studs, for Heat Resistance and High Temperature Applications
• Effective Date: 01-Nov-2004

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F 2281 – 03
Standard Specification for
Stainless Steel and Nickel Alloy Bolts, Hex Cap Screws, and
Studs, for Heat Resistance and High Temperature
1
Applications
This standard is issued under the fixed designation F 2281; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope A 582/A 582M Specification for Free-Machining Stainless
2
Steel Bars
1.1 This specification covers the chemical and mechanical
A 751 Test Methods, Practices, and Terminology for
requirements for stainless steel and nickel alloy bolts, hex cap
2
Chemical Analysis of Steel Products
1
screws, and studs, ⁄4 in. diameter and larger, intended for use
B 637 Specification for Precipitation-Hardening Nickel Al-
at temperatures up to 1800°F (982°C), and in applications
loy Bars, Forgings, and Forging Stock for High-
where resistance to heat and the effects of high temperature are
4
Temperature Service
to be considered. SeeAppendix X1 for ServiceApplication.A
B 880 Specification for General Requirements for Chemical
wide variety of materials are covered in this specification
Check Analysis Limits for Nickel, Nickel Alloys, and
which can be used at high temperatures as a function of the
4
Cobalt Alloys
specific alloy properties, as well as environmental require-
5
D 3951 Practice for Commercial Packaging
ments including corrosive environments.
E 21 Test Methods for Elevated Temperature Tension Tests
1.2 The values stated in inch-pound units are to be regarded
6
of Metallic Materials
as the standard.
E 29 Practice for Using Significant Digits in Test Data to
1.3 This standard does not purport to address all of the
7
Determine Conformance with Specifications
safety concerns, if any, associated with its use. It is the
E 76 Test Methods for ChemicalAnalysis of Nickel-Copper
responsibility of the user of this standard to establish appro-
8
Alloys
priate safety and health practices and determine the applica-
E 139 Test Methods for Conducting Creep, Creep-Rupture,
bility of regulatory requirements prior to use.
6
and Stress-Rupture Tests of Metallic Materials
2. Referenced Documents
E 292 Test Methods for Conducting Time-for-Rupture
6
Notch Tension Tests of Materials
2.1 ASTM Standards:
E 353 Test Methods for Chemical Analysis of Stainless,
A 262 Practices for Detecting Susceptibility to Intergranu-
2
Heat-Resisting, Maraging, and Other Similar Chromium-
lar Attack in Austenitic Stainless Steels
8
2
Nickel-Iron Alloys
A 276 Specification for Stainless Steel Bars and Shapes
E 354 Test Methods for Chemical Analysis of High-
A 342/A 342M Test Methods for Permeability of Feebly
3
Temperature, Electrical, Magnetic, and Other Similar Iron,
Magnetic Materials
8
Nickel, and Cobalt Alloys
A 380 Practice for Cleaning, Descaling, and Passivation of
2
F 606 Test Methods for Determining the Mechanical Prop-
Stainless Steel Parts, Equipment, and Systems
erties of Externally and Internally Threaded Fasteners,
A 484/A 484M Specification for General Requirements for
9
2
Washers, and Rivets
Stainless Steel Bars, Billets, and Forgings
F 788/F 788M Specification for Surface Discontinuities of
A 493 Specification for Stainless Steel Wire and Wire Rods
9
2
Bolts, Screws, and Studs, Inch and Metric Series
for Cold Heading and Cold Forging
F 1470 GuideforFastenerSamplingforSpecifiedMechani-
A 564/A 564M Specification for Hot-Rolled and Cold-
9
2
cal Properties and Performance Inspection
Finished Age-Hardening Stainless Steel Bars and Shapes
1 4
This specification is under the jurisdiction of ASTM Committee F16 on Annual Book of ASTM Standards, Vol 02.04.
5
Fasteners and is the direct responsibility of Subcommittee F16.04 on Nonferrous Annual Book of ASTM Standards, Vol 15.09.
6
Fasteners. Annual Book of ASTM Standards, Vol 03.01.
7
Current edition approved June 10, 2003. Published July 2003. Annual Book of ASTM Standards, Vol 14.02.
2 8
Annual Book of ASTM Standards, Vol 01.03. Annual Book of ASTM Standards, Vol 03.05.
3 9
Annual Book of ASTM Standards, Vol 03.04. Annual Book of ASTM Standards, Vol 01.08.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F2281–03
2.2 ASME Standards: 4.1.3.3 Class C—Precipitation Hardened alloy:
10
B1.1 Unified Inch Screw Threads
Alloy Grade UNS Designation
10
718 N07718
B18.2.1 Square and Hex Bolts and Screws, (Inch Series)
3. Terminology
5. Ordering Information
3.1 Definitions:
5.1 Orders for bolts, hex cap screws, and studs under this
3.1.1 heat resistance—the extent to which a material retains
specification shal
...