ASTM D3462/D3462M-10
(Specification)Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
ABSTRACT
This specification deals with the standards for asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surface on the weather side with minerals. Physical requirements of the shingles such as behavior on melting, tear strength, wind resistance, fire resistance, softening point, and pliability shall be measured immediately after packaging or at a reasonable time. Physical and performance requirements after application and during in-service use are however beyond the scope of this specification.
SCOPE
1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical and performance requirements after application and during in-service use of the products described herein are beyond the scope of this material specification.
1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm (2 in.).
1.3 The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during installation of the shingles.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D3462/D3462M – 10
Standard Specification for
Asphalt Shingles Made from Glass Felt and Surfaced with
1
Mineral Granules
This standard is issued under the fixed designation D3462/D3462M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope 2. Referenced Documents
2
1.1 This specification covers asphalt roofing in shingle 2.1 ASTM Standards:
form, composed of glass felt or felts impregnated and coated D5 Test Method for Penetration of Bituminous Materials
on both sides with asphalt, and surfaced on the weather side D36 Test Method for Softening Point of Bitumen (Ring-
with mineral granules. This specification is designed for the and-Ball Apparatus)
evaluation of products as manufactured. The test methods, D228 Test Methods for Sampling, Testing, and Analysis of
physical requirements, and minimum masses are to be mea- Asphalt Roll Roofing, Cap Sheets, and Shingles Used in
sured immediately after packaging or at a reasonable time, as Roofing and Waterproofing
agreed upon between buyer and seller, after manufacture and D1079 Terminology Relating to Roofing andWaterproofing
before installation. Physical and performance requirements D1922 Test Method for Propagation Tear Resistance of
after application and during in-service use of the products Plastic Film and Thin Sheeting by Pendulum Method
described herein are beyond the scope of this material speci- D3161 Test Method for Wind-Resistance of Asphalt
fication. Shingles (Fan-Induced Method)
1.2 Shingles meeting this specification are intended to be D4977 Test Method for Granule Adhesion to Mineral Sur-
applied with a headlap of not less than 51 mm (2 in.). faced Roofing by Abrasion
1.3 The shingles shall be supplied with a factory-applied E108 Test Methods for Fire Tests of Roof Coverings
self-sealing adhesive or be designed to be locked together
3. Terminology
during installation of the shingles.
1.4 The values stated in either SI units or inch-pound units 3.1 Definitions:
3.1.1 For definitions of terms, see Terminology D1079.
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each 3.1.2 For testing purposes, under Test Methods D228, glass
felt shall be considered as felt.
system shall be used independently of the other. Combining
values from the two systems may result in non-conformance
4. Materials and Manufacture
with the standard.
4.1 The glass felt shall be a thin porous sheet composed
1.5 The following safety hazards caveat pertains only to the
predominately of fine glass fibers uniformly deposited in a
test method described in this specification: This standard does
nonwoven pattern. It is permitted to reinforce the glass felt
not purport to address all of the safety concerns, if any,
withrandomorparallel-orientedglassyarns,orboth,whichare
associated with its use. It is the responsibility of the user of this
permitted to be gathered or twisted, bonded or unbonded. The
standard to establish appropriate safety and health practices
felt shall contain a substantially water-insoluble binding agent.
and determine the applicability of regulatory limitations prior
4.2 In the process of manufacture, one or more thicknesses
to use.
of glass felt shall be impregnated with an asphaltic material.
When more than one thickness of felt is used, the mats shall be
1
This specification is under the jurisdiction of ASTM Committee D08 on
Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02
2
on Steep Roofing Products and Assemblies. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved June 15, 2010. Published July 2010. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1983. Last previous edition approved in 2009 as D3462 – 09a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D3462_D3462M-09A. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D3462/D3462M – 10
adhered to each other with a continuous layer of asphaltic 6.2 The shingles shall not vary in length or width by more
1
material between adjacent felts. The nature of the asphaltic than 3.2 mm (6 ⁄8 in.) from nominal dimensions established
material and the thickness of the adhering layers shall ensure a for each size, except that the length (long dimension) of
firm bon
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D3462/D3462M–09a Designation: D3462/D3462M – 10
Standard Specification for
Asphalt Shingles Made from Glass Felt and Surfaced with
1
Mineral Granules
This standard is issued under the fixed designation D3462/D3462M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope
1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both
sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of
products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after
packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical
and performance requirements after application and during in-service use of the products described herein are beyond the scope
of this material specification.
1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm (2 in.).
1.3 The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during
installation of the shingles.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not
purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to
establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D5 Test Method for Penetration of Bituminous Materials
D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)
D228 Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing
and Waterproofing
D1079 Terminology Relating to Roofing and Waterproofing
D1922 Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
D3161 Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)
D4977 Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion
E108 Test Methods for Fire Tests of Roof Coverings
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms, see Terminology D1079.
3.1.2 For testing purposes, under Test Methods D228, glass felt shall be considered as felt.
4. Materials and Manufacture
4.1 The glass felt shall be a thin porous sheet composed predominately of fine glass fibers uniformly deposited in a nonwoven
1
This specification is under the jurisdiction ofASTM Committee D08 on Roofing and Waterproofing and is the direct responsibility of Subcommittee D08.02 on Prepared
Roofings, Shingles and Siding Materials.
Current edition approved July 1, 2009. Published August 2009. Originally approved in 1983. Last previous edition approved in 2009 as D3462–09. DOI:
10.1520/D3462_D3462M-09A.on Steep Roofing Products and Assemblies.
Current edition approved June 15, 2010. Published July 2010. Originally approved in 1983. Last previous edition approved in 2009 as D3462 – 09a. DOI:
10.1520/D3462_D3462M-09A.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D3462/D3462M – 10
pattern. It is permitted to reinforce the glass felt with random or parallel-oriented glass yarns, or both, which are permitted to be
gathered or twisted, bonded or unbonded. The felt shall contain a substantially water-insoluble binding agent.
4.2 In the process of ma
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.