ASTM F3080-17a
(Practice)Standard Practice for Laser Technologies for Measurement of Cross-Sectional Shape of Pipeline and Conduit by Non-Rotating Laser Projector and CCTV Camera System
Standard Practice for Laser Technologies for Measurement of Cross-Sectional Shape of Pipeline and Conduit by Non-Rotating Laser Projector and CCTV Camera System
SIGNIFICANCE AND USE
4.1 Laser profiling assessment is a quality control tool for identifying and quantifying deformation, physical damage, and other pipe anomalies after installation, providing means and methods for determining the quality of workmanship and compliance with project specifications. Laser profiling can be used for:
4.1.1 Measurement of the structural shape, cross sectional area and defects;
4.1.2 Collection of data needed for pipe rehabilitation or replacement design; and
4.1.3 Post rehabilitation, replacement or new construction workmanship verification.
4.2 A laser profile pre-acceptance and condition assessment survey provides significant information in a clear and concise manner, including but not limited to graphs and still frame digital images of pipe condition prior to acceptance, thereby providing objective data on the installed quality and percentage ovality, deformation, deflection or deviation, that is often not possible from an inspection by either a mandrel or CCTV only survey.
SCOPE
1.1 Laser profiling is a non-contact inspection method used to create a pipe wall profile and internal measurement using a standard CCTV pipe inspection system, 360 degree laser light projector, and special geometrical profiling software. This practice covers the procedure for the measurement to determine any deviation of the internal surface of installed pipe compared to the design. The measurements may be used to verify that the installation has met design requirements for acceptance or to collect data that will facilitate an assessment of the condition of pipe or conduit due to structural deviations or deterioration. This standard practice provides minimum requirements on means and methods for laser profiling to meet the needs of engineers, contractors, owners, regulatory agencies, and financing institutions.
1.2 This practice applies to all types of pipe material, all types of construction, and pipe shapes.
1.3 This practice applies to depressurized and gravity flow storm sewers, drains, sanitary sewers, and combined sewers with diameters from 6 to 72 in. (150 and 1800 mm).
1.4 This standard does not include all aspects of pipe inspection, such as joint gaps, soil/water infiltration in joints, cracks, holes, surface damage, repairs, corrosion, and structural problems associated with these conditions.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 The profiling process may require physical access to lines, entry manholes, and operations along roadways that may include safety hazards.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. There are no safety hazards specifically, however, associated with the use of the laser ring profiler specified (listed and labeled as specified in 1.3).
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F3080 − 17a
Standard Practice for
Laser Technologies for Measurement of Cross-Sectional
Shape of Pipeline and Conduit by Non-Rotating Laser
1
Projector and CCTV Camera System
This standard is issued under the fixed designation F3080; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.7 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 Laser profiling is a non-contact inspection method used
responsibility of the user of this standard to establish appro-
to create a pipe wall profile and internal measurement using a
priate safety, health, and environmental practices and deter-
standard CCTV pipe inspection system, 360 degree laser light
mine the applicability of regulatory limitations prior to use.
projector, and special geometrical profiling software. This
There are no safety hazards specifically, however, associated
practice covers the procedure for the measurement to deter-
with the use of the laser ring profiler specified (listed and
mine any deviation of the internal surface of installed pipe
labeled as specified in 1.3).
compared to the design. The measurements may be used to
1.8 This international standard was developed in accor-
verify that the installation has met design requirements for
dance with internationally recognized principles on standard-
acceptance or to collect data that will facilitate an assessment
ization established in the Decision on Principles for the
of the condition of pipe or conduit due to structural deviations
Development of International Standards, Guides and Recom-
or deterioration. This standard practice provides minimum
mendations issued by the World Trade Organization Technical
requirements on means and methods for laser profiling to meet
Barriers to Trade (TBT) Committee.
the needs of engineers, contractors, owners, regulatory
agencies, and financing institutions.
2. Referenced Documents
1.2 This practice applies to all types of pipe material, all
2
2.1 ASTM Standards:
types of construction, and pipe shapes.
E177 Practice for Use of the Terms Precision and Bias in
1.3 This practice applies to depressurized and gravity flow
ASTM Test Methods
storm sewers, drains, sanitary sewers, and combined sewers
E691 Practice for Conducting an Interlaboratory Study to
with diameters from 6 to 72 in. (150 and 1800 mm).
Determine the Precision of a Test Method
F1216 Practice for Rehabilitation of Existing Pipelines and
1.4 This standard does not include all aspects of pipe
Conduits by the Inversion and Curing of a Resin-
inspection, such as joint gaps, soil/water infiltration in joints,
Impregnated Tube
cracks,holes,surfacedamage,repairs,corrosion,andstructural
2.2 Other Standards:
problems associated with these conditions.
IEC 60825-1 Safety of Laser Products – Part 1: Equipment
1.5 The values stated in inch-pound units are to be regarded
3
Classification and Requirements, Jan 2011.
as standard. The values given in parentheses are mathematical
CDRH Regulations CFR 21, Section I, Subchapter J, Parts
conversions to SI units that are provided for information only
4
1002 to 1040.11
and are not considered standard.
1.6 The profiling process may require physical access to
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
lines, entry manholes, and operations along roadways that may
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
include safety hazards.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
1 3
This practice is under the jurisdiction ofASTM Committee F36 on Technology Available from International Electrotechnical Commission (IEC), 3, rue de
and Underground Utilities and is the direct responsibility of Subcommittee F36.20 Varembé, 1st Floor, P.O. Box 131, CH-1211 Geneva 20, Switzerland, http://
on Inspection and Renewal of Water and Wastewater Infrastructure. www.iec.ch.
4
Current edition approved Dec. 1, 2017. Published December 2017. Originally Available from Center for Devices and Radiological Health (CDRH), Food and
approved in 2014. Last previous edition approved in 2017 as F3080-17. DOI: Drug Administration, 10903 New Hampshire Avenue, WO66-4621, Silver Spring,
10.1520/F3080-17A. MD 20993, http://www.fda.gov.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F3080 − 17a
3. Terminology 3.1.15 survey calibrator
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F3080 − 17 F3080 − 17a
Standard Practice for
Laser Technologies for Measurement of Cross-Sectional
Shape of Pipeline and Conduit by Non-Rotating Laser
1
Projector and CCTV Camera System
This standard is issued under the fixed designation F3080; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 Laser profiling is a non-contact inspection method used to create a pipe wall profile and internal measurement using a
standard CCTV pipe inspection system, 360 degree laser light projector, and special geometrical profiling software. This practice
covers the procedure for the measurement to determine any deviation of the internal surface of installed pipe compared to the
design. The measurements may be used to verify that the installation has met design requirements for acceptance or to collect data
that will facilitate an assessment of the condition of pipe or conduit due to structural deviations or deterioration. This standard
practice provides minimum requirements on means and methods for laser profiling to meet the needs of engineers, contractors,
owners, regulatory agencies, and financing institutions.
1.2 This practice applies to all types of pipe material, all types of construction, and pipe shapes.
1.3 This practice applies to depressurized and gravity flow storm sewers, drains, sanitary sewers, and combined sewers with
diameters from 6 to 72 in. (150 and 1800 mm).
1.4 This standard does not include all aspects of pipe inspection, such as joint gaps, soil/water infiltration in joints, cracks, holes,
surface damage, repairs, corrosion, and structural problems associated with these conditions.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.6 The profiling process may require physical access to lines, entry manholes, and operations along roadways that may include
safety hazards.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use. There are no safety hazards specifically, however, associated with the use of
the laser ring profiler specified (listed and labeled as specified in 1.3).
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods
E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
F1216 Practice for Rehabilitation of Existing Pipelines and Conduits by the Inversion and Curing of a Resin-Impregnated Tube
2.2 Other Standards:
3
IEC 60825-1 Safety of Laser Products – Part 1: Equipment Classification and Requirements, Jan 2011.
1
This practice is under the jurisdiction of ASTM Committee F36 on Technology and Underground Utilities and is the direct responsibility of Subcommittee F36.20 on
Inspection and Renewal of Water and Wastewater Infrastructure.
Current edition approved April 1, 2017Dec. 1, 2017. Published May 2017December 2017. Originally approved in 2014. Last previous edition approved in 20142017 as
F3080-14.-17. DOI: 10.1520/F3080-17.10.1520/F3080-17A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from International Electrotechnical Commission (IEC), 3, rue de Varembé, 1st Floor, P.O. Box 131, CH-1211 Geneva 20, Switzerland, http://www.iec.ch.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
-------------------
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.