ASTM E3202-19e1
(Practice)Standard Practice for Specimen Preparation and Mounting of Plastic Composites for Use as Deck Boards, Stair Treads, Guards or Handrails to Assess Surface Burning Characteristics
Standard Practice for Specimen Preparation and Mounting of Plastic Composites for Use as Deck Boards, Stair Treads, Guards or Handrails to Assess Surface Burning Characteristics
SIGNIFICANCE AND USE
5.1 Plastic composite materials for use as deck boards, stair treads, guards or handrails are evaluated in accordance with Test Method E84 to comply with building or residential code requirements. This Practice describes specimen mounting procedures for such materials.
5.2 The material to be tested shall be representative of the materials used in actual field installations.
Note 2: Test Method E84 assesses the comparative burning behavior of building materials. Thus, this practice addresses specimen preparation and mounting of materials at use thickness, with full width tunnel coverage.
5.3 The limitations for this procedure are those associated with Test Method E84.
SCOPE
1.1 This practice describes a procedure for specimen preparation and mounting when testing plastic composite materials for use as deck boards, stair treads, guards or handrails to assess flame spread index as a surface burning characteristic using Test Method E84.
1.2 This practice applies to plastic composite materials, including plastic lumber and wood-plastic composites. The test specimens shall be self-supporting or held in place by added supports along the test surface, in accordance with Annex A4 of Test Method E84.
1.3 This practice does not provide pass/fail criteria that can be used as a regulatory tool.
1.4 This practice is applicable to (a) materials that are self-supporting and (b) materials that are not self-supporting but where the test specimen is held in place by added supports throughout the test duration without such severe sagging that it interferes with the effect of the gas flame on the test specimen.
Note 1: Paragraph 1.4 reflects requirements contained in plastic lumber specifications.
1.5 Use the values stated in inch-pound units as the standard in referee decisions. The values in the SI system of units are given in parentheses, for information only; see IEEE/ASTM SI-10 for further details.
1.6 This fire standard cannot be used to provide quantitative measures.
1.7 Fire testing of products and materials is inherently hazardous and adequate safeguards for personnel and property shall be employed in conducting these tests. Fire testing involves hazardous materials, operations and equipment.
1.8 This practice gives instructions on specimen preparation and mounting but the fire-test-response method shall be conducted in accordance with Test Method E84. See also Section 8 for information on operator safety.
1.9 The text of this practice references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered requirements of the standard.
1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
´1
Designation: E3202 − 19 An American National Standard
Standard Practice for
Specimen Preparation and Mounting of Plastic Composites
for Use as Deck Boards, Stair Treads, Guards or Handrails
1
to Assess Surface Burning Characteristics
This standard is issued under the fixed designation E3202; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
ε NOTE—The terms flame spread index and smoke developed index were moved editorially from under the heading Defi-
nitions of Terms Specific to this Standard to Definitions, 3.1, in July 2020.
1. Scope 1.8 This practice gives instructions on specimen preparation
and mounting but the fire-test-response method shall be con-
1.1 This practice describes a procedure for specimen prepa-
ducted in accordance with Test Method E84. See also Section
ration and mounting when testing plastic composite materials
8 for information on operator safety.
for use as deck boards, stair treads, guards or handrails to
assess flame spread index as a surface burning characteristic 1.9 The text of this practice references notes and footnotes
using Test Method E84. which provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered
1.2 This practice applies to plastic composite materials,
requirements of the standard.
including plastic lumber and wood-plastic composites.The test
1.10 This standard does not purport to address all of the
specimens shall be self-supporting or held in place by added
safety concerns, if any, associated with its use. It is the
supports along the test surface, in accordance with Annex A4
responsibility of the user of this standard to establish appro-
of Test Method E84.
priate safety, health, and environmental practices and deter-
1.3 This practice does not provide pass/fail criteria that can
mine the applicability of regulatory limitations prior to use.
be used as a regulatory tool.
1.11 This international standard was developed in accor-
1.4 This practice is applicable to (a) materials that are
dance with internationally recognized principles on standard-
self-supporting and (b) materials that are not self-supporting
ization established in the Decision on Principles for the
but where the test specimen is held in place by added supports
Development of International Standards, Guides and Recom-
throughout the test duration without such severe sagging that it
mendations issued by the World Trade Organization Technical
interferes with the effect of the gas flame on the test specimen.
Barriers to Trade (TBT) Committee.
NOTE 1—Paragraph 1.4 reflects requirements contained in plastic
2. Referenced Documents
lumber specifications.
2
2.1 ASTM Standards:
1.5 Use the values stated in inch-pound units as the standard
D883 Terminology Relating to Plastics
in referee decisions. The values in the SI system of units are
E84 Test Method for Surface Burning Characteristics of
given in parentheses, for information only; see IEEE/ASTM
Building Materials
SI-10 for further details.
E176 Terminology of Fire Standards
1.6 This fire standard cannot be used to provide quantitative
E2579 Practice for Specimen Preparation and Mounting of
measures.
Wood Products to Assess Surface Burning Characteristics
1.7 Fire testing of products and materials is inherently IEEE/ASTM SI-10 International System of Units (SI) The
hazardous and adequate safeguards for personnel and property Modernized Metric System
shall be employed in conducting these tests. Fire testing
3. Terminology
involves hazardous materials, operations and equipment.
3.1 Definitions: For definitions of terms used in this practice
and associated with fire issues refer to Terminology E176. For
1
This practice is under the jurisdiction of ASTM Committee E05 on Fire
2
Standards and is the direct responsibility of Subcommittee E05.22 on Surface For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Burning. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved Sept. 1, 2019. Published September 2019. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/E3202-19E01. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´1
E3202 − 19
of building materials. Thus, this practice addresses specimen prepar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.