ASTM C1731-16
(Specification)Standard Specification for Concrete Floor Tile
Standard Specification for Concrete Floor Tile
ABSTRACT
This specification establishes the product criteria and minimum performance requirements for concrete floor tile (CFT) used as interior and exterior flooring. The units described by this specification are manufactured from cementitious materials, mineral aggregates (normal weight, lightweight, or both), water, and additives that are cast into various textures and shapes, often simulating natural stone, brick, terracotta, saltillo, and others. The standard addresses materials and their manufacture, physical properties, sampling, packaging and package marking, and certification.
SCOPE
1.1 This specification covers concrete floor tile (CFT) for application as interior and exterior flooring. The units described by this specification are manufactured from cementitious materials, mineral aggregates (normal weight, lightweight, or both), water, and additives that are cast into various textures and shapes, often simulating natural stone, brick, terracotta, saltillo, and others.
1.2 This specification is limited to requirements for the physical attributes for the CFT units.
1.3 The use of results from testing installed CFT units that have been removed from use for determining conformance or nonconformance to the requirements of this specification is beyond the scope of this specification.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1731 −16
Standard Specification for
1
Concrete Floor Tile
This standard is issued under the fixed designation C1731; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
The purpose of this specification is to establish the product specifications and minimum
performance requirements of concrete floor tile.
1. Scope* C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylin-
1.1 This specification covers concrete floor tile (CFT) for
drical Concrete Specimens
application as interior and exterior flooring. The units de-
C140/C140M Test Methods for Sampling and Testing Con-
scribed by this specification are manufactured from cementi-
crete Masonry Units and Related Units
tious materials, mineral aggregates (normal weight,
C150/C150M Specification for Portland Cement
lightweight, or both), water, and additives that are cast into
C157/C157M Test Method for Length Change of Hardened
various textures and shapes, often simulating natural stone,
Hydraulic-Cement Mortar and Concrete
brick, terracotta, saltillo, and others.
C172/C172M Practice for Sampling Freshly Mixed Con-
1.2 This specification is limited to requirements for the
crete
physical attributes for the CFT units.
C260/C260M Specification for Air-Entraining Admixtures
1.3 The use of results from testing installed CFT units that
for Concrete
have been removed from use for determining conformance or
C331/C331M Specification for Lightweight Aggregates for
nonconformance to the requirements of this specification is
Concrete Masonry Units
beyond the scope of this specification.
C482 Test Method for Bond Strength of Ceramic Tile to
1.4 The values stated in inch-pound units are to be regarded
Portland Cement Paste
as standard. The values given in parentheses are mathematical
C494/C494M Specification for Chemical Admixtures for
conversions to SI units that are provided for information only
Concrete
and are not considered standard.
C595/C595M Specification for Blended Hydraulic Cements
1.5 This standard does not purport to address all of the C618 Specification for Coal Fly Ash and Raw or Calcined
safety concerns, if any, associated with its use. It is the Natural Pozzolan for Use in Concrete
responsibility of the user of this standard to establish appro-
C979/C979M Specification for Pigments for Integrally Col-
priate safety and health practices and determine the applica-
ored Concrete
bility of regulatory limitations prior to use.
C989/C989M Specification for Slag Cement for Use in
Concrete and Mortars
2. Referenced Documents
C1093 Practice for Accreditation of Testing Agencies for
2
2.1 ASTM Standards:
Masonry
C31/C31M Practice for Making and Curing Concrete Test
C1116/C1116M Specification for Fiber-Reinforced Concrete
Specimens in the Field
C1157/C1157M Performance Specification for Hydraulic
Cement
1 C1232 Terminology of Masonry
This specification is under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and is the direct responsibility of Subcommittee
C1353/C1353M Test Method for Abrasion Resistance of
C15.03 on Concrete Masonry Units and Related Units.
Dimension Stone Subjected to FootTraffic Using a Rotary
CurrenteditionapprovedJune1,2016.PublishedJuly2016.Originallyapproved
Platform Abraser
in 2013. Last previous edition approved in 2015 as C1731 – 15. DOI: 10.1520/
C1731–16.
C1600/C1600M Specification for Rapid Hardening Hydrau-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
lic Cement
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
C1602/C1602M Specification for Mixing Water Used in the
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Production of Hydraulic Cement Concrete
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1731 − 16
C1645/C1645M Test Method for Freeze-thaw and De-icing 5. Physical Properties
Salt Durability of Solid Concrete Interlocking Paving
5.1 Dimensions:
Units
1
5.1.1 CFT units shall have a minimum thickness of ⁄4 in.
NOTE 1—An installation guide for concrete floor tile (CFT) is being (6.4 mm) and a maximum thickness of 1.2 in. (30 mm).
developed concurrently in Subcommittee C15.05 Masonry Assemblies.
5.1.2 CFT units shall not exceed 36 in. (914 mm) in any
face dimension.
2.2 ANSI Standards:
5.1.3 Dimensional Tolerances:
A137.1-2012 American National Standard Specification for
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1731 − 15 C1731 − 16
Standard Specification for
1
Concrete Floor Tile
This standard is issued under the fixed designation C1731; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
INTRODUCTION
The purpose of this specification is to establish the product specifications and minimum
performance requirements of concrete floor tile.
1. Scope*
1.1 This specification covers concrete floor tile (CFT) for application as interior and exterior flooring. The units described by
this specification are manufactured from cementitious materials, mineral aggregates (normal weight, lightweight, or both), water,
and additives that are cast into various textures and shapes, often simulating natural stone, brick, terracotta, saltillo, and others.
1.2 This specification is limited to requirements for the physical attributes for the CFT units.
1.3 The use of results from testing installed CFT units that have been removed from use for determining conformance or
nonconformance to the requirements of this specification is beyond the scope of this specification.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C31/C31M Practice for Making and Curing Concrete Test Specimens in the Field
C33/C33M Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C140/C140M Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
C150/C150M Specification for Portland Cement
C157/C157M Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete
C172/C172M Practice for Sampling Freshly Mixed Concrete
C260/C260M Specification for Air-Entraining Admixtures for Concrete
C331/C331M Specification for Lightweight Aggregates for Concrete Masonry Units
C482 Test Method for Bond Strength of Ceramic Tile to Portland Cement Paste
C494/C494M Specification for Chemical Admixtures for Concrete
C595/C595M Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C979/C979M Specification for Pigments for Integrally Colored Concrete
C989/C989M Specification for Slag Cement for Use in Concrete and Mortars
1
This specification is under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and is the direct responsibility of Subcommittee C15.03 on
Concrete Masonry Units and Related Units.
Current edition approved July 1, 2015June 1, 2016. Published July 2015July 2016. Originally approved in 2013. Last previous edition approved in 20132015 as C1731
– 13.15. DOI: 10.1520/C1731–15.10.1520/C1731–16.
2
The last approved version For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For of this
historicalAnnual Book of ASTM Standards standard is referenced on www.astm.org.volume information, refer to the standard’s Document Summary page on the ASTM
website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1731 − 16
C1028 Test Method for Determining the Static Coefficient of Friction of Ceramic Tile and Other Like Surfaces by the Horizontal
2
Dynamometer Pull-Meter Method (Withdrawn 2014)
C1093 Practice for Accreditation of Testing Agencies for Masonry
C1116/C1116M Specification for Fiber-Reinforced Concrete
C1157/C1157M Performance Specification for Hydraulic Cement
C1232 Terminology of Masonry
C1353/C1353M Test Method for Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform
Abraser
C1600/C1600M Specification for Rapid Hardening Hydraulic Cement
C1602/C1602M Specification for Mixing Water Used in the Production of Hydraulic Ceme
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.