ASTM C140/C140M-16
(Test Method)Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
SIGNIFICANCE AND USE
4.1 These test methods provide general testing requirements for application to a broad range of concrete products. Those general testing requirements are included in the body of this standard.
Note 2: Consult manufacturer, supplier, product specifications, or other resources for more specific measurement or testing guidelines for those products not addressed with the annex of this standard.
4.2 These test methods provide specific testing requirements in two distinct sections, the requirements applicable to all units covered by these test methods and those applicable to the specific unit types. The requirements applicable to all units are included in the body of these test methods and those applicable to the specific unit types are included within the annexes.
SCOPE
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength, absorption, unit weight (density), moisture content, flexural load, and ballast weight. Not all methods are applicable to all unit types, however.
1.2 Specific testing and reporting procedures are included in annexes to these test methods for the following specific unit types:
Annex A1—Concrete masonry units (Specifications C90, C129)
Annex A2—Concrete and calcium silicate brick
(Specifications C55, C73, C1634)
Annex A3—Segmental retaining wall units (Specification C1372)
Annex A4—Concrete interlocking paving units
(Specification C936/C936M)
Annex A5—Concrete grid paving units (Specification C1319)
Annex A6—Concrete roof pavers (Specification C1491)
Annex A7—Dry-cast articulating concrete block
(Specification D6684)
1.3 The test procedures included in these test methods are also applicable to other types of units not referenced in these test methods, but specific testing and reporting requirements for those units are not included.
1.4 These test methods include the following sections:
Section
Scope
1
Referenced Documents
2
Terminology
3
Significance and Use
4
Sampling
5
Measurement of Dimensions
6
Compressive Strength
7
Absorption
8
Calculations
9
Report
10
Keywords
11
Annexes—Test Procedures
Concrete Masonry Units
Annex A1
Concrete and Calcium Silicate Brick
Annex A2
Segmental Retaining
Wall Units
Annex A3
Concrete Interlocking Paving Units
Annex A4
Concrete Grid Paving
Units
Annex A5
Concrete Roof Pavers
Annex A6
Dry-Cast Articulating
Concrete Block
Annex A7
Determining Plate Thickness
Requirements for
Compression Testing
Annex A8
Worksheet and Test Report for
Concrete Masonry Units
Appendix X1
Note 1: The testing laboratory performing these test methods should be evaluated in accordance with Practice C1093.
1.5 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C140/C140M − 16
Standard Test Methods for
Sampling and Testing Concrete Masonry Units and Related
1
Units
This standard is issued under the fixed designation C140/C140M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
Section
Annexes—Test Procedures
1.1 These test methods provide various testing procedures
Concrete Masonry Units Annex A1
commonly used for evaluating characteristics of concrete Concrete and Calcium Silicate Brick Annex A2
Segmental Retaining Annex A3
masonryunitsandrelatedconcreteunits.Methodsareprovided
Wall Units
for sampling, measurement of dimensions, compressive
Concrete Interlocking Paving Units Annex A4
strength, absorption, unit weight (density), moisture content, Concrete Grid Paving Annex A5
Units
flexural load, and ballast weight. Not all methods are appli-
Concrete Roof Pavers Annex A6
cable to all unit types, however.
Dry-Cast Articulating Annex A7
Concrete Block
1.2 Specifictestingandreportingproceduresareincludedin
Determining Plate Thickness Annex A8
annexes to these test methods for the following specific unit
Requirements for
Compression Testing
types:
Worksheet and Test Report for Appendix X1
Annex A1—Concrete masonry units (Specifications C90, C129)
Concrete Masonry Units
Annex A2—Concrete and calcium silicate brick
NOTE 1—The testing laboratory performing these test methods should
(Specifications C55, C73, C1634)
Annex A3—Segmental retaining wall units (Specification C1372) be evaluated in accordance with Practice C1093.
Annex A4—Concrete interlocking paving units
1.5 The text of this test method references notes and
(Specification C936/C936M)
Annex A5—Concrete grid paving units (Specification C1319)
footnotes that provide explanatory material. These notes and
Annex A6—Concrete roof pavers (Specification C1491)
footnotes (excluding those in tables and figures) shall not be
Annex A7—Dry-cast articulating concrete block
considered as requirements of the standard.
(Specification D6684)
1.6 The values stated in either SI units or inch-pound units
1.3 The test procedures included in these test methods are
also applicable to other types of units not referenced in these are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
test methods, but specific testing and reporting requirements
system shall be used independently of the other. Combining
for those units are not included.
values from the two systems may result in non-conformance
1.4 These test methods include the following sections:
with the standard.
Section
1.7 This standard does not purport to address all of the
Scope 1
Referenced Documents 2
safety concerns, if any, associated with its use. It is the
Terminology 3
responsibility of the user of this standard to establish appro-
Significance and Use 4
priate safety and health practices and determine the applica-
Sampling 5
Measurement of Dimensions 6
bility of regulatory limitations prior to use.
Compressive Strength 7
Absorption 8
2. Referenced Documents
Calculations 9
2
Report 10
2.1 ASTM Standards:
Keywords 11
C55Specification for Concrete Building Brick
C73Specification for Calcium Silicate Brick (Sand-Lime
Brick)
1
These test methods are under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and are the direct responsibility of Subcommittee
2
C15.03 on Concrete Masonry Units and Related Units. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
CurrenteditionapprovedJune1,2016.PublishedJuly2016.Originallyapproved contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
ɛ1
in 1938. Last previous edition approved in 2015 as C140–15a . DOI: 10.1520/ Standards volume information, refer to the standard’s Document Summary page on
C0140_C0140M-16. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C140/C140M − 16
C90Specification for Loadbearing Concrete Masonry Units dimensions. Specimens shall be representative of the whole lot
C129Specification for Nonloadbearing Concrete Masonry of units from which they are selected.
Units
5.2 Number of Specimens:
C143/C143MTest Method for Slump of Hydraulic-Cement
5.2.1 Unless specified otherwise in the applicable annex, a
Concrete
set of units shall consist of six full-size units.
C936/C936MSpecification for So
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´1
Designation: C140/C140M − 15a C140/C140M − 16
Standard Test Methods for
Sampling and Testing Concrete Masonry Units and Related
1
Units
This standard is issued under the fixed designation C140/C140M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Editorial corrections were made throughout the standard in February 2016.
1. Scope*
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry
units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength,
absorption, unit weight (density), moisture content, flexural load, and ballast weight. Not all methods are applicable to all unit
types, however.
1.2 Specific testing and reporting procedures are included in annexes to these test methods for the following specific unit types:
Annex A1—Concrete masonry units (Specifications C90, C129)
Annex A2—Concrete and calcium silicate brick
(Specifications C55, C73, C1634)
Annex A3—Segmental retaining wall units (Specification C1372)
Annex A4—Concrete interlocking paving units
(Specification C936/C936M)
Annex A5—Concrete grid paving units (Specification C1319)
Annex A6—Concrete roof pavers (Specification C1491)
Annex A7—Dry-cast articulating concrete block
(Specification D6684)
1.3 The test procedures included in these test methods are also applicable to other types of units not referenced in these test
methods, but specific testing and reporting requirements for those units are not included.
1.4 These test methods include the following sections:
Section
Scope 1
Referenced Documents 2
Terminology 3
Significance and Use 4
Sampling 5
Measurement of Dimensions 6
Compressive Strength 7
Absorption 8
Calculations 9
Report 10
Keywords 11
Annexes—Test Procedures
Concrete Masonry Units Annex A1
Concrete and Calcium Silicate Brick Annex A2
Segmental Retaining Annex A3
Wall Units
Concrete Interlocking Paving Units Annex A4
Concrete Grid Paving Annex A5
Units
Concrete Roof Pavers Annex A6
Dry-Cast Articulating Annex A7
Concrete Block
1
These test methods are under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and are the direct responsibility of Subcommittee C15.03 on
Concrete Masonry Units and Related Units.
Current edition approved Dec. 15, 2015June 1, 2016. Published January 2016July 2016. Originally approved in 1938. Last previous edition approved in 2015 as
ɛ1
C140 – 15.C140 – 15a . DOI: 10.1520/C0140_C0140M-15AE01.10.1520/C0140_C0140M-16.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C140/C140M − 16
Section
Determining Plate Thickness Annex A8
Requirements for
Compression Testing
Worksheet and Test Report for Appendix X1
Concrete Masonry Units
NOTE 1—The testing laboratory performing these test methods should be evaluated in accordance with Practice C1093.
1.5 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C55 Specification for Concrete Building Brick
C73 Specification for Calcium Silicate Brick (Sand-Lime Brick)
C90 Specification for Loadbearing Concrete Masonry Units
C129 Specification for Nonloadbearing Concrete Masonry Units
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C936/C936M Specification for Solid Concre
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.