ASTM C170/C170M-17
(Test Method)Standard Test Method for Compressive Strength of Dimension Stone
Standard Test Method for Compressive Strength of Dimension Stone
SIGNIFICANCE AND USE
4.1 This test method is useful in indicating the differences in compressive strength between the various dimension stones. This test method also provides one element in comparing stones of the same type.
SCOPE
1.1 This test method covers the sampling, preparation of specimens, and determination of the compressive strength of dimension stone.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C170/C170M − 17
Standard Test Method for
1
Compressive Strength of Dimension Stone
This standard is issued under the fixed designation C170/C170M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope D7012 Test Methods for Compressive Strength and Elastic
Moduli of Intact Rock Core Specimens under Varying
1.1 This test method covers the sampling, preparation of
States of Stress and Temperatures
specimens, and determination of the compressive strength of
E4 Practices for Force Verification of Testing Machines
dimension stone.
1.2 The values stated in either SI units or inch-pound units
3. Terminology
are to be regarded separately as standard. The values stated in
3.1 Definitions—All definitions are in accordance with Ter-
each system may not be exact equivalents; therefore, each
minology C119.
system shall be used independently of the other. Combining
values from the two systems may result in non-conformance
4. Significance and Use
with the standard.
4.1 Thistestmethodisusefulinindicatingthedifferencesin
1.3 This standard does not purport to address all of the
compressive strength between the various dimension stones.
safety concerns, if any, associated with its use. It is the
This test method also provides one element in comparing
responsibility of the user of this standard to establish appro-
stones of the same type.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
5. Apparatus
1.4 This international standard was developed in accor-
5.1 The testing machine used shall conform to the require-
dance with internationally recognized principles on standard-
ments of Test Method C39, Section 5, including the calibration
ization established in the Decision on Principles for the
requirements of Practices E4.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
5.2 The testing machine used shall be capable of applying
Barriers to Trade (TBT) Committee.
the required load at a uniform rate as prescribed in Section 9
and applying load in a steady manner as to avoid sudden or
2. Referenced Documents
rapid load changes.
2
2.1 ASTM Standards:
5.3 The spherical bearing block of the testing machine shall
C39 Test Method for Compressive Strength of Cylindrical
be suspended from the upper head so that the contact plate
Concrete Specimens
remains in a central position (spherical surfaces in full contact)
C119 Terminology Relating to Dimension Stone
when not loaded. The spherical surfaces shall be well
C1799 Guide to Dimension Stone Test Specimen Sampling
lubricated, and the center of curvature shall be aligned within
and Preparation
the surface of contact with the specimen.
D4543 PracticesforPreparingRockCoreasCylindricalTest
5.4 Fig.1illustratesthecorrectalignmentofaspecimenand
Specimens and Verifying Conformance to Dimensional
the typical components of a testing machine conforming to
and Shape Tolerances
these requirements.
6. Sampling
1
This test method is under the jurisdiction of ASTM Committee C18 on
Dimension Stone and is the direct responsibility of Subcommittee C18.01 on Test
6.1 The sample shall be selected to represent a true average
Methods.
of the type or grade of stone under consideration and shall be
Current edition approved April 1, 2017. Published April 2017. Originally
of the quality supplied to the market in finished form under the
approved in 1941. Last previous edition approved in 2016 as C170/C170M–16.
DOI: 10.1520/C0170_C0170M-17.
type designation to be tested. The samples may be selected by
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
the purchaser or his authorized representative from quarried
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
stone or taken from the natural ledge and shall be of adequate
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. size to permit the preparation of the desired number of test
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C170/C170M − 17
7.2 The ratio of height (the distance between the surfaces in
contact with the testing apparatus) to the diameter or late
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C170/C170M − 16 C170/C170M − 17
Standard Test Method for
1
Compressive Strength of Dimension Stone
This standard is issued under the fixed designation C170/C170M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This test method covers the sampling, preparation of specimens, and determination of the compressive strength of
dimension stone.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C39 Test Method for Compressive Strength of Cylindrical Concrete Specimens
C119 Terminology Relating to Dimension Stone
C1799 Guide to Dimension Stone Test Specimen Sampling and Preparation
D4543 Practices for Preparing Rock Core as Cylindrical Test Specimens and Verifying Conformance to Dimensional and Shape
Tolerances
D7012 Test Methods for Compressive Strength and Elastic Moduli of Intact Rock Core Specimens under Varying States of
Stress and Temperatures
E4 Practices for Force Verification of Testing Machines
3. Terminology
3.1 Definitions—All definitions are in accordance with Terminology C119.
4. Significance and Use
4.1 This test method is useful in indicating the differences in compressive strength between the various dimension stones. This
test method also provides one element in comparing stones of the same type.
5. Apparatus
5.1 The testing machine used shall conform to the requirements of Test Method C39, Section 5, including the calibration
requirements of Practices E4.
5.2 The testing machine used shall be capable of applying the required load at a uniform rate as prescribed in Section 9 and
applying load in a steady manner as to avoid sudden or rapid load changes.
1
This test method is under the jurisdiction of ASTM Committee C18 on Dimension Stone and is the direct responsibility of Subcommittee C18.01 on Test Methods.
Current edition approved March 15, 2016April 1, 2017. Published March 2016April 2017. Originally approved in 1941. Last previous edition approved in 20152016 as
C170/C170M–15b.–16. DOI: 10.1520/C0170_C0170M-16.10.1520/C0170_C0170M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C170/C170M − 17
5.3 The spherical bearing block of the testing machine shall be suspended from the upper head so that the contact plate remains
in a central position (spherical surfaces in full contact) when not loaded. The spherical surfaces shall be well lubricated, and the
center of curvature shall be aligned within the surface of contact with the specimen.
5.4 Fig. 1 illustrates the correct alignment of a specimen and the typical components of a testing machine conforming to these
requirements.
6. Sampling
6.1 The sample shall be selected to represent a true average of the type or grade of stone under consideration and shall be of
the quality supplied to the market in finished form under the type designation to be tested. The samples may be selected by the
purchaser or his authorized representative from quarried stone or taken from the natural ledge a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.