ASTM A313/A313M-17

Standard Specification for Stainless Steel Spring Wire

ABSTRACT
This guide covers standard specification for austenitic and age-hardenable stainless steel round spring wire intended especially for the manufacture of springs. The steel shall conform to the required chemical composition for carbon, manganese, phosphorus, sulfur, silicon, chromium, nickel, molybdenum, nitrogen, and other elements. The material shall conform to the required tensile strengths following the prescribed heat treatment. Tensile strength requirements for hardened wires and stress-relieved materials shall be given. Mechanical tests such as wrap test, uniformity (coil test), and bend test hall be performed on the steel material.
SCOPE
1.1 This specification covers austenitic, austenitic-ferritic, and age-hardenable stainless steel round spring wire intended especially for the manufacture of springs.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Oct-2017
• ICS: 77.140.25 - Spring steels
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.17 - Flat-Rolled and Wrought Stainless Steel

Relations

• Replaces: ASTM A313/A313M-13 - Standard Specification for Stainless Steel Spring Wire
• Effective Date: 01-Nov-2017
• Replaced By: ASTM A313/A313M-18 - Standard Specification for Stainless Steel Spring Wire
• Effective Date: 01-Sep-2018
• Referred By: ASTM F1370-92(2019)e1 - Standard Specification for Pressure-Reducing Valves for Water Systems, Shipboard
• Effective Date: 01-Nov-2017
• Referred By: ASTM A555/A555M-23 - Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods
• Effective Date: 01-Nov-2017
• Referred By: ASTM F1546-23 - Standard Specification for Fire Hose Nozzles
• Effective Date: 01-Nov-2017
• Referred By: ASTM F2332-06(2022) - Standard Specification for Annular Ball Bearings for Instruments and Precision Rotating Components
• Effective Date: 01-Nov-2017
• Referred By: ASTM F1511-18(2023) - Standard Specification for Mechanical Seals for Shipboard Pump Applications
• Effective Date: 01-Nov-2017
• Referred By: ASTM F1508-96(2021) - Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
• Effective Date: 01-Nov-2017
• Referred By: ASTM F899-20 - Standard Specification for Wrought Stainless Steels for Surgical Instruments
• Effective Date: 01-Nov-2017

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A313/A313M −17
Standard Specification for
1
Stainless Steel Spring Wire
This standard is issued under the fixed designationA313/A313M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 3. Ordering Information
1.1 This specification covers austenitic, austenitic-ferritic, 3.1 It is the responsibility of the purchaser to specify all
and age-hardenable stainless steel round spring wire intended requirements that are necessary for material ordered under this
especially for the manufacture of springs. specification. Such requirements may include, but are not
limited to the following:
1.2 The values stated in either SI units or inch-pound units
3.1.1 Quantity (weight),
are to be regarded separately as standard. The values stated in
3.1.2 Name of material (stainless steel spring wire),
each system may not be exact equivalents; therefore, each
3.1.3 Finish (see 8.1),
system shall be used independently of the other. Combining
3.1.4 Dimension (diameter),
values from the two systems may result in non-conformance
3.1.5 Type designation (Table 1),
with the standard.
3.1.6 ASTM designation and date of issue,
1.3 Unless the order specifies an “M” designation, the
3.1.7 Tensile strength level, when applicable (Table 11 and
material shall be furnished to inch-pound units.
Table 12),
1.4 This international standard was developed in accor- 3.1.8 Supplementary requirements for government
dance with internationally recognized principles on standard-
procurement, and
ization established in the Decision on Principles for the 3.1.9 Special requirements.
Development of International Standards, Guides and Recom-
NOTE 1—A typical ordering description is as follows:
mendations issued by the World Trade Organization Technical
2000 lb (1000 kg) Stainless Steel Spring Wire, cold-drawn Class 1,
Barriers to Trade (TBT) Committee.
bright finish, 0.032-in. (0.82 mm) diameter, in 100-lb (50 kg) 16-in. (0.4
m) coils, Type 302 to ASTM A313, dated ____.
2. Referenced Documents
4. General Requirements for Delivery
2
2.1 ASTM Standards:
4.1 In addition to the requirements of this specification, all
A555/A555M Specification for General Requirements for
requirements of the current edition of Specification A555/
Stainless Steel Wire and Wire Rods
A555M shall apply. Failure to comply with the general
A751 Test Methods, Practices, and Terminology for Chemi-
requirements of Specification A555/A555M constitutes non-
cal Analysis of Steel Products
conformance with this specification.
E527 Practice for Numbering Metals and Alloys in the
Unified Numbering System (UNS)
5. Manufacture
3
2.2 Society of Automotive Engineers Standard:
5.1 Types 302 Class 1, 304, 305, 316, 321, 347, UNS
J 1086 Numbering Metals and Alloys
S20230, and Grades S20430 and XM-28 shall be cold drawn to
produce the required mechanical properties.
5.2 Type 631, Type 302 Class 2, and Grade XM-16 shall be
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
furnished in the cold-drawn condition ready for fabrication.
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
A01.17 on Flat-Rolled and Wrought Stainless Steel.
Following fabricationType 631 and Grade XM-16 shall be age
Current edition approved Nov. 1, 2017. Published November 2017. Originally
or precipitation hardened to produce their maximum strength
approved in 1947. Last previous edition approved in 2013 as A313/A313M – 13.
properties. The tensile strengths to be obtained following the
DOI: 10.1520/A0313_A0313M-17.
2
prescribed heat treatment are shown in Table 2 and Table 3 for
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
hardened wire. Type 302 Class 2 shall be stress relieved
Standards volume information, refer to the standard’s Document Summary page on
following fabrication and meet the requirements shown in
the ASTM website.
3
Table 4. The nominal as-drawn tensile strengths are provided
Available from Society of Automotive Engineers (SAE), 400 Commonwealth
Dr., Warrendale, PA 15096-0001, http://www.sae.org. as a guide for the spring manufacturer.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A313/A313M−17
TABLE 1 Chemical Requirements
B
Composition, %
UNS
Type
A
Designation
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A313/A313M − 13 A313/A313M − 17
Standard Specification for
1
Stainless Steel Spring Wire
This standard is issued under the fixed designation A313/A313M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This specification covers austenitic, austenitic-ferritic, and age-hardenable stainless steel round spring wire intended
especially for the manufacture of springs.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 Unless the order specifies an “M” designation, the material shall be furnished to inch-pound units.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A555/A555M Specification for General Requirements for Stainless Steel Wire and Wire Rods
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
3
2.2 Society of Automotive Engineers Standard:
J 1086 Numbering Metals and Alloys
3. Ordering Information
3.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this
specification. Such requirements may include, but are not limited to the following:
3.1.1 Quantity (weight),
3.1.2 Name of material (stainless steel spring wire),
3.1.3 Finish (see 8.1),
3.1.4 Dimension (diameter),
3.1.5 Type designation (Table 1),
3.1.6 ASTM designation and date of issue,
3.1.7 Tensile strength level, when applicable (Table 11 and Table 12),
3.1.8 Supplementary requirements for government procurement, and
3.1.9 Special requirements.
NOTE 1—A typical ordering description is as follows:
2000 lb (1000 kg) Stainless Steel Spring Wire, cold-drawn Class 1, bright finish, 0.032-in. (0.82 mm) diameter, in 100-lb (50 kg) 16-in. (0.4 m) coils,
Type 302 to ASTM A313, dated ____.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Oct. 1, 2013Nov. 1, 2017. Published October 2013November 2017. Originally approved in 1947. Last previous edition approved in 20102013
ε1
as A313/A313M – 10A313/A313M – 13. . DOI: 10.1520/A0313_A0313M-13.10.1520/A0313_A0313M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A313/A313M − 17
TABLE 1 Chemical Requirements
B
Composition, %
UNS
Type
A
Designation
Carbon Manganese Phosphorus Sulfur Silicon Chromium Nickel Molybdenum Nitrogen Other Elements
Austenitic Grades
S 20230 . . . 0.02–0.06 2.0–6.0 0.045 0.030 1.00 17.0–19.0 2.0–4.5 1.0 0.13–0.25 Cu 2.0–4.0
S 20430 . . . 0.15 6.5–9.0 0.060 0.030 1.00 15.5–17.5 1.5–3.5 . . . 0.05–0.25 Cu 2.0–4.0
S 24100 XM-28 0.15 11.0–14.0 0.060 0.030 1.00 16.5–19.0 0.50–2.50 0.20–0.45
S 24100 XM-28 0.15 11.0–14.0 0.060 0.030 1.00 16.5–19.0 0.50–2.50 . . . 0.20–0.45 . . .
S 30151 . . . 0.07–0.09 1.50–2.00 0.025 0.010 1.20–1.80 16.0–18.0 7.0–9.0 0.50–1.00 0.07–0.11 Cu 0.40
S 30200 302 0.12 2.00 0.045 0.030 1.00 17.0–19.0 8.0–10.0 . . . 0.10 . . .
S 30400 304 0.08 2.00 0.045 0.030 1.00 18.0–20.0 8.0–1
...