Standard Specification for Circular Precast Reinforced Concrete Manhole Sections

ABSTRACT
This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer and water works. Reinforced concrete shall consist of cementitious materials, mineral aggregates, and water, in which steel reinforcement has been embedded in such a manner so that the steel reinforcement and concrete act together. Aggregates shall conform to the specification , except that the requirements for gradation shall not apply. Minimum compressive strength of concrete manhole products covered must meet the requirement. The aggregates shall be sized, graded, proportioned, and mixed with such proportions of cementitious materials and water as will produce as homogeneous concrete mixture of such quality that the products will conform to the test and design requirements. Concrete products shall be subjected to either steam or water curing. Test methods such as compression and absorption testing shall be performed.
SCOPE
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of circular vertical precast reinforced concrete manholes and structures used in sewer, drainage, and water works.  
1.2 Part I, Sections 1 – 11, of this specification presents general requirements and requirements that are common to each precast concrete product covered by this specification.  
1.3 Part II of this specification presents specific requirements for each manhole product in the following sections:    
Product  
Section  
Grade Rings  
12  
Flat Slab Tops  
13  
Risers and Conical Tops  
14  
Base Sections  
15  
Steps and Ladders  
16  
Note 1: Future products will to be included in Part II in a future revision of this specification.  
1.4 This specification is the inch-pound companion to Specification C478M; therefore, no SI equivalents are presented in the specification.
Note 2: This specification is a manufacturing and purchase specification only and does not include requirements for backfill, or the relationship between field load conditions and the strength requirements of the manhole products and appurtenances. Experience has shown, however, that the successful performance of this product depends upon the proper selection of the product strength, type of foundation and backfill, and care in the field installation of the manhole products and connecting pipes. The owner of the project for which these products are specified herein is cautioned to require inspection at the construction site.

General Information

Status
Historical
Publication Date
31-Dec-2014
Technical Committee
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM C478-15 - Standard Specification for Circular Precast Reinforced Concrete Manhole Sections
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM C478-15 - Standard Specification for Circular Precast Reinforced Concrete Manhole Sections
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C478 −15
StandardSpecification for
1
Circular Precast Reinforced Concrete Manhole Sections
This standard is issued under the fixed designation C478; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
PART I—GENERAL 2. Referenced Documents
2
2.1 ASTM Standards:
1. Scope
A615/A615M SpecificationforDeformedandPlainCarbon-
1.1 This specification covers the manufacture and purchase
Steel Bars for Concrete Reinforcement
requirements of products used for the assembly and construc-
A706/A706M Specification for Deformed and Plain Low-
tion of circular vertical precast reinforced concrete manholes
Alloy Steel Bars for Concrete Reinforcement
and structures used in sewer, drainage, and water works.
A1064/A1064M Specification for Carbon-Steel Wire and
1.2 Part I, Sections1–11, of this specification presents
Welded Wire Reinforcement, Plain and Deformed, for
general requirements and requirements that are common to
Concrete
each precast concrete product covered by this specification.
C33 Specification for Concrete Aggregates
1.3 Part II of this specification presents specific require-
C39/C39M Test Method for Compressive Strength of Cylin-
ments for each manhole product in the following sections: drical Concrete Specimens
C150 Specification for Portland Cement
Product Section
Grade Rings 12
C260 Specification for Air-Entraining Admixtures for Con-
Flat Slab Tops 13
crete
Risers and Conical Tops 14
Base Sections 15
C309 Specification for Liquid Membrane-Forming Com-
Steps and Ladders 16
pounds for Curing Concrete
NOTE 1—Future products will to be included in Part II in a future C494/C494M Specification for Chemical Admixtures for
revision of this specification.
Concrete
1.4 This specification is the inch-pound companion to C497 Test Methods for Concrete Pipe, Manhole Sections, or
Specification C478M; therefore, no SI equivalents are pre- Tile
sented in the specification. C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined
NOTE 2—This specification is a manufacturing and purchase specifica-
Natural Pozzolan for Use in Concrete
tion only and does not include requirements for backfill, or the relation-
ship between field load conditions and the strength requirements of the
C822 Terminology Relating to Concrete Pipe and Related
manhole products and appurtenances. Experience has shown, however,
Products
that the successful performance of this product depends upon the proper
C989 Specification for Slag Cement for Use in Concrete and
selection of the product strength, type of foundation and backfill, and care
Mortars
in the field installation of the manhole products and connecting pipes.The
owner of the project for which these products are specified herein is
C1017/C1017M Specification for Chemical Admixtures for
cautioned to require inspection at the construction site.
Use in Producing Flowing Concrete
C1602/C1602M Specification for Mixing Water Used in the
Production of Hydraulic Cement Concrete
3
2.2 ACI Standard:
318 Building Code, Requirements for Reinforced Concrete
1 2
This specification is under the jurisdiction of ASTM Committee C13 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Concrete Pipe and is the direct responsibility of Subcommittee C13.06 on Manholes contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
and Specials. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Jan. 1, 2015. Published January 2015. Originally the ASTM website.
3
approved in 1961. Last previous edition approved in 2014 as C478 – 14. DOI: Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington
10.1520/C0478-15. Hills, MI 48333-9094, http://www.aci-int.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C478−15
3. Terminology steel reinforced concrete manholes as a non-structural manu-
facturingenhancement.Onlyfibersdesignedandmanufactured
3.1 Definitions—For definitions of terms relating to precast
specifically for use in concrete and so certified by the manu-
reinforced concrete manholes, see Terminology C822.
facturer shall be accepted.
4.1.9 Other Materials—Other materials required for a prod-
4. Materials and Manufacture
uct and not covered in Section 4 will be covered in the Part II
4.1 General material requirements for precast reinforced
section for that specific product.
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C478 − 14 C478 − 15
Standard Specification for
1
Circular Precast Reinforced Concrete Manhole Sections
This standard is issued under the fixed designation C478; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
PART I—GENERAL
1. Scope
1.1 This specification covers the manufacture and purchase requirements of products used for the assembly and construction of
circular vertical precast reinforced concrete manholes and structures used in sewer, drainage, and water works.
1.2 Part I, Sections 1 – 11, of this specification presents general requirements and requirements that are common to each precast
concrete product covered by this specification.
1.3 Part II of this specification presents specific requirements for each manhole product in the following sections:
Product Section
Grade Rings 12
Flat Slab Tops 13
Risers and Conical Tops 14
Base Sections 15
Steps and Ladders 16
NOTE 1—Future products will to be included in Part II in a future revision of this specification.
1.4 This specification is the inch-pound companion to Specification C478M; therefore, no SI equivalents are presented in the
specification.
NOTE 2—This specification is a manufacturing and purchase specification only and does not include requirements for backfill, or the relationship
between field load conditions and the strength requirements of the manhole products and appurtenances. Experience has shown, however, that the
successful performance of this product depends upon the proper selection of the product strength, type of foundation and backfill, and care in the field
installation of the manhole products and connecting pipes. The owner of the project for which these products are specified herein is cautioned to require
inspection at the construction site.
1
This specification is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.06 on Manholes and Specials.
Current edition approved Sept. 15, 2014Jan. 1, 2015. Published October 2014January 2015. Originally approved in 1961. Last previous edition approved in 20132014 as
C478 – 13.C478 – 14. DOI: 10.1520/C0478-14.10.1520/C0478-15.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C478 − 15
2. Referenced Documents
2
2.1 ASTM Standards:
A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
A706/A706M Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement
A1064/A1064M Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete
C33 Specification for Concrete Aggregates
C39/C39M Test Method for Compressive Strength of Cylindrical Concrete Specimens
C150 Specification for Portland Cement
C260 Specification for Air-Entraining Admixtures for Concrete
C309 Specification for Liquid Membrane-Forming Compounds for Curing Concrete
C494/C494M Specification for Chemical Admixtures for Concrete
C497 Test Methods for Concrete Pipe, Manhole Sections, or Tile
C595 Specification for Blended Hydraulic Cements
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C822 Terminology Relating to Concrete Pipe and Related Products
C989 Specification for Slag Cement for Use in Concrete and Mortars
C1017/C1017M Specification for Chemical Admixtures for Use in Producing Flowing Concrete
C1602/C1602M Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete
3
2.2 ACI Standard:
318 Building Code, Requirements for Reinforced Concrete
3. Terminology
3.1 Definitions—For definitions of terms relating to precast reinforced concrete manholes, see Terminology C822.
4. Materials and Manufacture
4.1 General material requirements for precast reinforced concrete manhole products are presented in 4.1.1 – 4.1.84.1.9. Other
materials or additional requirements for a product, if any, are covered in the Part II section for that specific product.
4.1.1 Reinforced Concrete—Reinforced concrete shall consist of cementitious materials, mineral aggregates, and water, in
which steel reinforcement has been embedded in such a manner so that the ste
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.