ASTM D4314-05

Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorosulfonated Polyethylene (CSM) Jackets For Wire and Cable

ABSTRACT
This specification covers the standard requirements for crosslinked chlorosulfonated polyethylene compounds intended for use as jacket materials (outer coverings) on electrical wires and cables for general-purpose, heavy-duty, and extra-heavy-duty service. The materials under this specification, however, are not recommended for applications with very low temperature service requirement. Physical tests shall be performed to assess the conformance of the jacket material with the physical property requirements such as tensile strength, tensile stress at elongation, elongation at rupture, tension set, and tear. Per service requirement, additional tests for sunlight and weather resistance shall be performed as well, and shall conform to the requirements specified.
SCOPE
1.1 This specification covers crosslinked chlorosulfonated polyethylene compounds suitable for use as outer coverings or jackets on electrical cables for general-purpose, heavy-duty, and extra-heavy-duty service.
1.2 These jacket materials are not recommended for cables installed at a temperature lower than 25C.
1.3 Whenever two sets of values are presented, in different units, the values in the first set are the standard, while those in parentheses are for information only.

General Information

• Status: Historical
• Publication Date: 28-Feb-2005
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: D09 - Electrical and Electronic Insulating Materials

Relations

• Replaces: ASTM D4314-99 - Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorosulfonated Polyethylene (CSM) Jackets For Wire and Cable
• Effective Date: 01-Mar-2005
• Replaced By: ASTM D4314-12 - Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorosulfonated Polyethylene (CSM) Jackets For Wire and Cable (Withdrawn 2017)
• Effective Date: 01-Jan-2012

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: D4314 – 05
Standard Specification for
General-Purpose, Heavy-Duty, and Extra-Heavy-Duty
Crosslinked Chlorosulfonated Polyethylene (CSM) Jackets
1
For Wire and Cable
This standard is issued under the fixed designation D4314; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 For definitions of terms used in this specification refer
to Terminology D1711.
1.1 This specification covers crosslinked chlorosulfonated
2
3.2 Definitions of Terms Specific to This Standard:
polyethylene compoundssuitableforuseasoutercoveringsor
3.2.1 aging (act of), n—exposure of materials to air at 100
jackets on electrical cables for general-purpose, heavy-duty,
°C for 168 h or oil at 121 °C for 18 h.
and extra-heavy-duty service.
1.2 These jacket materials are not recommended for cables
4. Test Applicable for Sunlight and Weather– Resistant
installed at a temperature lower than −25°C.
Materials
1.3 Whenever two sets of values are presented, in different
4.1 For jackets requiring sunlight- and weather-resistance
units, the values in the first set are the standard, while those in
testing, test in accordance with “Weatherability for Colored
parentheses are for information only.
Materials” in Specification D1248. Prepare the specimens in
2. Referenced Documents accordance with Test Methods D470 for physical tests of
3
insulations and jackets.
2.1 ASTM Standards:
D470 Test Methods for Crosslinked Insulations and Jackets
5. Physical Properties
for Wire and Cable
5.1 The jacket shall conform to the requirements for physi-
D1248 Specification for Polyethylene Plastics Extrusion
cal properties prescribed in Table 1.
Materials for Wire and Cable
D1711 Terminology Relating to Electrical Insulation
6. Sampling
6.1 Sample the jacket in accordance with Test Methods
3. Terminology
D470.
3.1 Definitions:
7. Test Methods
1
This specification is under the jurisdiction of ASTM Committee D09 on
7.1 Unless otherwise instructed, test the jacket in accor-
Electrical and Electronic Insulating Materials and is the direct responsibility of
dance with Test Methods D470.
SubcommitteeD09.18onSolidInsulations,Non-MetallicShieldingsandCoverings
for Electrical and Telecommunications Wires and Cables.
8. Keywords
Current edition approved March 1, 2005. Published March 2005. Originally
approved in 1983. Last previous edition approved in 1999 as D4314–99. DOI:
8.1 crosslinked chlorosulfonated polyethylene jacket; cross-
10.1520/D4314-05
...