ASTM D4313-22

Standard Specification for General-Purpose, Heavy-Duty, and Extra-Heavy-Duty Crosslinked Chlorinated Polyethylene (CPE) Jackets For Wire and Cable

ABSTRACT
This specification covers crosslinked chlorinated polyethylene compounds intended for use as jacket materials (outer coverings) on electrical wires and cables for general-purpose, heavy-duty, and extra-heavy-duty service. The materials under this specification, however, are not recommended for applications with very low temperature service requirement. Physical tests shall be performed and shall conform to the physical property requirements specified such as tensile strength, tensile stress at elongation, elongation at rupture, and tension set. Per service requirement, additional tests for sunlight and weather resistance shall be performed as well, and shall conform to the tensile strength and elongation requirements specified.
SCOPE
1.1 This specification covers crosslinked chlorinated polyethylene (CPE) compounds suitable for use as outer coverings or jackets on electrical cables for general-purpose, heavy-duty, and extra-heavy-duty service.  
1.2 These jacket materials are not recommended for use on cables which are to be installed at a temperature less than –25 °C.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 30-Apr-2022
• ICS: 29.035.20 - Plastics and rubber insulating materials
• Technical Committee: D09 - Electrical and Electronic Insulating Materials
• Drafting Committee: D09.07 - Electrical Insulating Materials

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:D4313 −22
Standard Specification for
General-Purpose, Heavy-Duty, and Extra-Heavy-Duty
Crosslinked Chlorinated Polyethylene (CPE) Jackets For
1
Wire and Cable
This standard is issued under the fixed designation D4313; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Terminology
1.1 This specification covers crosslinked chlorinated poly- 3.1 Definitions:
ethylene (CPE) compounds suitable for use as outer coverings 3.1.1 For definitions of terms used in this specification refer
or jackets on electrical cables for general-purpose, heavy-duty, to Terminology D1711.
and extra-heavy-duty service. 3.1.2 aging (act of), n—exposure of material to air or oil at
a temperature and time as specified in the relevant material
1.2 These jacket materials are not recommended for use on
specification for that material.
cables which are to be installed at a temperature less
than –25 °C.
4. Physical Properties
1.3 The values stated in inch-pound units are to be regarded
4.1 Crosslinked jackets shall conform to the requirements
as standard. The values given in parentheses are mathematical
for physical properties specified in Table 1.
conversions to SI units that are provided for information only
4.2 Tensile Strength and Percent Elongation at Rupture:
and are not considered standard.
4.2.1 The test is conducted in accordance withTest Methods
1.4 This international standard was developed in accor-
D470. The requirements for tensile strength and elongation are
dance with internationally recognized principles on standard-
given in Table 1 of this Specification.
ization established in the Decision on Principles for the
4.3 Tensile Strength and Percent Elongation at Rupture
Development of International Standards, Guides and Recom-
After Oil Immersion:
mendations issued by the World Trade Organization Technical
4.3.1 Fluid as specified in the product Standard shall be
Barriers to Trade (TBT) Committee.
used.
2. Referenced Documents
4.3.2 The test is conducted in accordance withTest Methods
2
D470. The requirements for tensile strength and elongation are
2.1 ASTM Standards:
given in Table 1 of this Specification.
D470 Test Methods for Crosslinked Insulations and Jackets
for Wire and Cable
5. Sunlight and Weather Resistance Requirements
D1499 Practice for Filtered Open-Flame Carbon-Arc Expo-
sures of Plastics 5.1 Test the jacket in accordance with Test Methods D470.
D1711 Terminology Relating to Electrical Insulation
If sunlight and weather resistance are required of the cross-
G153 Practice for Operating Enclosed Carbon Arc Light linked jackets, the jackets shall conform to the requirements
Apparatus for Exposure of Nonmetallic Materials
specified in Table 2.
6. Sampling
1
This specification is under the jurisdiction of ASTM Committee D09 on
Electrical and Electronic Insulating Materials and is the direct responsibility of
6.1 Sample the jacket in accordance with Test Methods
Subcommittee D09.07 on Electrical Insulating Materials.
D470.
Current edition approved May 1, 2022. Published June 2022. Originally
approved in 1987. Last previous edition approved in 2021 as D4313 – 21. DOI:
7. Test Methods
10.1520/D4313-22.
2
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D4313 − 21 D4313 − 22
Standard Specification for
General-Purpose, Heavy-Duty, and Extra-Heavy-Duty
Crosslinked Chlorinated Polyethylene (CPE) Jackets For
1
Wire and Cable
This standard is issued under the fixed designation D4313; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers crosslinked chlorinated polyethylene (CPE) compounds suitable for use as outer coverings or jackets
on electrical cables for general-purpose, heavy-duty, and extra-heavy-duty service.
1.2 These jacket materials are not recommended for use on cables which are to be installed at a temperature less than –25 °C.
than –25 °C.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D470 Test Methods for Crosslinked Insulations and Jackets for Wire and Cable
D1499 Practice for Filtered Open-Flame Carbon-Arc Exposures of Plastics
D1711 Terminology Relating to Electrical Insulation
G153 Practice for Operating Enclosed Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
3. Terminology
3.1 Definitions:
3.1.1 For definitions of terms used in this specification refer to Terminology D1711.
3.1.2 aging (act of), n—exposure of material to air or oil at a temperature and time as specified in the relevant material
specification for that material.
1
This specification is under the jurisdiction of ASTM Committee D09 on Electrical and Electronic Insulating Materials and is the direct responsibility of Subcommittee
D09.07 on Electrical Insulating Materials.
Current edition approved July 1, 2021May 1, 2022. Published July 2021June 2022. Originally approved in 1987. Last previous edition approved in 20172021 as
D4313 – 17.D4313 – 21. DOI: 10.1520/D4313-21.10.1520/D4313-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D4313 − 22
3.2 Definitions of Terms Specific to This Standard:
3.2.1 aging (act of), n—exposure of materials to air at a temperature of 121 °C for 168 h and oil at 121 °C for 18 h.
4. Physical Properties
4.1 Crosslinked jackets shall conform to the requirements for physical properties specified in Table 1.
4.2 Tensile Strength and Percent Elongation at Rupture:
4.2.1 The test is conducted in accordance with Test Methods D470. The requirements for tensile strength and elongation are given
in Table 1 of this Specification.
4.3 Tensile Strength and Percent Elongation at Rupture After Oil Immersion:
4.3.1 Fluid as specified in the product Standard shall be used.
4.3.2 The test is conducted in accordance with Test Methods D470. The requirements for tensile strength and elongation are given
in Table 1 of this Specification.
5. Sunlight and Weather Resistance Requirements
5.1 Test the jacket in accordance with Test Methods D470. If sunlight and weather resistance are required of the crosslinked
jackets, the jackets shall conform to the requirements specified in Table 2.
6. Sampling
6.1 Sample the jacket in accordance with Test Methods D470.
7. Test Methods
7.1 Test the jacket in accordance with Test Methods D470. If the sunlight and weather resistance test is required, perform it in
accordance with Practices D1499 and G153.
TABLE 1 Physical Properties for CPE Jacket
General-purpose Heavy-duty Extra-heavy-duty
Physical Requirements (Original):
Tensile strength, min, psi (MPa) 1200 (8.3) 1800 (12.4) 2400 (16.5)
Tensile stress at 200 % elongation, min, psi (MPa) . .
...