iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F3029-13

(Guide)

Standard Guide for Level I GPS Wilderness Navigator (GPS-IW) Endorsement (Withdrawn 2014)

Standard Guide for Level I GPS Wilderness Navigator (GPS-IW) Endorsement (Withdrawn 2014)

SIGNIFICANCE AND USE
3.1 This guide establishes the minimum knowledge, skills, and abilities required to navigate in the wilderness using a GPS receiver. A person trained to this guide is an endorsed Level I GPS Wilderness Navigator (GPS-IW Endorsed).  
3.1.1 Every person who is identified as an endorsed Level I GPS Wilderness Navigator shall have met the requirements of this guide.  
3.2 This guide is only the first level of training for GPS Wilderness Navigators, and only establishes the minimum knowledge, skills, and abilities required for a person to navigate with a GPS receiver in a wilderness environment. No other advanced skills are included or implied.  
3.3 In addition to meeting the requirements of this guide, an endorsed Level I GPS Wilderness Navigator shall also be adequately trained to travel and work in a wilderness environment.  
3.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may navigate in a wilderness environment.  
3.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
3.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required of an endorsed Level I GPS Wilderness Navigator. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
3.6 Though this guide establishes only minimum training, it does not imply that an endorsed Level I GPS Wilderness Navigator is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
3.7 This guide can be used to evaluate a document to determine if its content meets the necessary topics for training a Level I GPS Wilderness Navigator. Likewise, the guide can be used to evaluate an existing training program to ...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to navigate in the wilderness using a GPS receiver.  
1.1.1 The information in this guide is for navigation on land, off-road, wherever GPS signals can be received.  
1.1.2 This guide does not define the minimum knowledge, skills, and abilities necessary for navigating by GPS on roads, in urban areas, on the water, or in the air.  
1.2 A person who meets the requirements in this guide is only prepared to navigate with a GPS receiver. Further training in wilderness travel and survival is required for users to operate in a wilderness environment.  
1.3 This guide does not imply that a GPS receiver is an alternative to navigating with map and compass. Use of map and compass is strongly recommended as a backup for GPS navigation.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This guide established the minimum knowledge, skills, and abilities required to navigate in the wilderness using a GPS receiver.
Formerly under the jurisdiction of Committee F32 on Search and Rescue, this guide was withdrawn in December 2013.

General Information

Status
Withdrawn
Publication Date
30-Jun-2013
Withdrawal Date
22-Jan-2014
ICS
33.070.40 - Satellite
Technical Committee
F32 - Search and Rescue
Drafting Committee
F32.03 - Personnel, Training and Education
Current Stage
Ref Project

Relations

Referred By
ASTM F1847-14(2022) - Standard Guide for Minimum Training of Search Dog Crews or Teams
Effective Date
01-Jul-2013

Buy Standard

ASTM F3029-13 - Standard Guide for Level I GPS Wilderness Navigator (GPS-IW) Endorsement (Withdrawn 2014)ASTM F3029-13 - Standard Guide for Level I GPS Wilderness Navigator (GPS-IW) Endorsement (Withdrawn 2014)
PreviousNext
Guide
ASTM F3029-13 - Standard Guide for Level I GPS Wilderness Navigator (GPS-IW) Endorsement (Withdrawn 2014)
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F3029 − 13
StandardGuide for
Level I GPS Wilderness Navigator (GPS-IW) Endorsement
This standard is issued under the fixed designation F3029; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.1.5 track, n—a three-dimensional trail defined by loca-
tions collected by a GPS receiver at specific intervals of time.
1.1 This guide establishes the minimum knowledge, skills,
2.1.6 waypoint, n—an intermediate point on a route or line
and abilities required to navigate in the wilderness using a GPS
of travel.
receiver.
1.1.1 Theinformationinthisguideisfornavigationonland,
3. Significance and Use
off-road, wherever GPS signals can be received.
3.1 This guide establishes the minimum knowledge, skills,
1.1.2 This guide does not define the minimum knowledge,
and abilities required to navigate in the wilderness using a GPS
skills, and abilities necessary for navigating by GPS on roads,
receiver. A person trained to this guide is an endorsed Level I
in urban areas, on the water, or in the air.
GPS Wilderness Navigator (GPS-IW Endorsed).
1.2 A person who meets the requirements in this guide is
3.1.1 Every person who is identified as an endorsed Level I
only prepared to navigate with a GPS receiver. Further training
GPS Wilderness Navigator shall have met the requirements of
in wilderness travel and survival is required for users to operate
this guide.
in a wilderness environment.
3.2 This guide is only the first level of training for GPS
1.3 This guide does not imply that a GPS receiver is an
Wilderness Navigators, and only establishes the minimum
alternative to navigating with map and compass. Use of map
knowledge, skills, and abilities required for a person to
and compass is strongly recommended as a backup for GPS
navigate with a GPS receiver in a wilderness environment. No
navigation.
other advanced skills are included or implied.
1.4 This standard does not purport to address all of the
3.3 In addition to meeting the requirements of this guide, an
safety concerns, if any, associated with its use. It is the
endorsed Level I GPS Wilderness Navigator shall also be
responsibility of the user of this standard to establish appro-
adequately trained to travel and work in a wilderness environ-
priate safety and health practices and determine the applica-
ment.
bility of regulatory limitations prior to use.
3.4 Depending on the regulations or policies of the AHJ,
2. Terminology
additional knowledge, skills, or abilities may be required
before a person who meets the requirements in this guide may
2.1 Definitions of Terms Specific to This Standard:
navigate in a wilderness environment.
2.1.1 authority having jurisdiction (AHJ), n—(1) the team,
3.4.1 Nothing in this guide precludes an AHJ from adding
organization, agency, or other entity using this guide; (2) the
additional requirements for its own members.
team, organization, agency, or other entity to which a person
being trained, tested, or evaluated belongs, if the instructor,
3.5 This guide by itself is not a complete training document.
evaluator, or tester is not a member of the same organization.
It only specifies the knowledge, skills, and abilities required of
an endorsed Level I GPS Wilderness Navigator. This guide
2.1.2 GPS receiver, n—a radio receiver that uses satellite
may, however, be used in the development of, or as part of, a
signals to fix its location on or above the earth’s surface.
complete training document or program.
2.1.3 map datum, n—the set of values used to define a
3.6 Though this guide establishes only minimum training, it
particular geodetic model.
does not imply that an endorsed Level I GPS Wilderness
2.1.4 route, n—a series of waypoints which define a virtual
Navigator is a “trainee,” “probationary,” or other similar term
path from one location to one or more other locations.
member of an organization. The AHJ is responsible for
determining the requirements and qualifications for member or
1 employee ratings.
This test method is under the jurisdiction of ASTM Committee F32 on Search
and Rescue and is the direct responsibility of Subcommittee F32.03 on Personnel,
3.7 This guide can be used to evaluate a document to
Training and Education.
determine if its content meets the ne
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F3071-14(2020)(Guide)
Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) Endorsement

SIGNIFICANCE AND USE
4.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS receiver to determine a position and collect navigational data in the wilderness. A person trained to this guide shall be endorsed for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW Endorsed).  
4.1.1 Every person who is endorsed for Basic Wilderness GPS/GNSS Use shall have met the requirements of this guide.  
4.2 This guide is only the first level of training for wilderness GPS/GNSS use, and only establishes the minimum knowledge, skills, and abilities required for a person to use a GPS/GNSS receiver to determine his or her location and collect navigational data in a wilderness environment. No other skills are included or implied.  
4.3 In addition to meeting the requirements of this guide, a person endorsed for Basic Wilderness GPS/GNSS Use shall also be adequately trained to travel and work in a wilderness environment.  
4.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may use a GPS/GNSS receiver in a wilderness environment.  
4.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
4.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required for an individual to be endorsed for Basic Wilderness GPS/GNSS Use. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
4.6 Though this guide establishes only minimum training, it does not imply that a person endorsed for Basic Wilderness GPS/GNSS Use is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
4.7 This guide can be used to evaluate a document to determine if its content includes the nec...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS2 receiver to determine one’s position, and collect location data, in the wilderness.  
1.2 This guide applies to the use of a GPS/GNSS receiver on land, on and off roads, and on small bodies of water, wherever GPS/GNSS signals can be received.  
1.3 This guide applies to the use of a GPS/GNSS receiver in disaster areas where local positioning aids or references may be lost or damaged.  
1.4 This guide does not apply to the use of a GPS/GNSS receiver on large bodies of water, at sea, or in the air.  
1.5 A person who meets the requirements in this guide is only prepared to operate a GPS/GNSS receiver to determine his or her location, and collect position and movement information, in a wilderness environment.  
1.6 This guide does not imply that a GPS/GNSS receiver is a replacement for a map and compass. Use of the latter is strongly recommended as a backup for GPS/GNSS navigation.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3072-14(2020)(Guide)
Standard Guide for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW) Endorsement

SIGNIFICANCE AND USE
4.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS receiver to navigate in the wilderness. A person trained to this guide shall be endorsed for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW Endorsed).  
4.1.1 Every person who is endorsed for Intermediate Wilderness GPS/GNSS Use shall have met the requirements of this guide.  
4.2 This guide is the second level of training for wilderness GPS/GNSS use, and only establishes the minimum knowledge, skills, and abilities required for a person to navigate with a GPS/GNSS receiver in a wilderness environment. No other skills are included or implied.  
4.3 In addition to meeting the requirements of this guide, a person endorsed for Intermediate Wilderness GPS/GNSS Use shall also be adequately trained to travel and work in a wilderness environment.  
4.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may use a GPS/GNSS receiver to navigate in a wilderness environment.  
4.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
4.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required for an individual to be endorsed for Intermediate Wilderness GPS/GNSS Use. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
4.6 Though this guide establishes only minimum training, it does not imply that a person endorsed for Intermediate Wilderness GPS/GNSS Use is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
4.7 This guide can be used to evaluate a document to determine if its content includes the necessary topics for training a person to be endorsed ...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS2 receiver to navigate in the wilderness.  
1.2 This guide applies to the use of a GPS/GNSS receiver on land, on and off roads, and on small bodies of water, wherever GPS/GNSS signals can be received.  
1.3 This guide applies to the use of a GPS/GNSS receiver in disaster areas where local positioning aids or references may be lost or damaged.  
1.4 This guide does not apply to the use of a GPS/GNSS receiver on large bodies of water, at sea, or in the air.  
1.5 This guide does not imply that a GPS/GNSS receiver is a replacement for a map and compass. Use of the latter is strongly recommended as a backup for GPS/GNSS navigation.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3071-14(2020)(Guide)
Standard Guide for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW) Endorsement

SIGNIFICANCE AND USE
4.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS receiver to determine a position and collect navigational data in the wilderness. A person trained to this guide shall be endorsed for Basic Wilderness GPS/GNSS Use (GPS/GNSS-IW Endorsed).  
4.1.1 Every person who is endorsed for Basic Wilderness GPS/GNSS Use shall have met the requirements of this guide.  
4.2 This guide is only the first level of training for wilderness GPS/GNSS use, and only establishes the minimum knowledge, skills, and abilities required for a person to use a GPS/GNSS receiver to determine his or her location and collect navigational data in a wilderness environment. No other skills are included or implied.  
4.3 In addition to meeting the requirements of this guide, a person endorsed for Basic Wilderness GPS/GNSS Use shall also be adequately trained to travel and work in a wilderness environment.  
4.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may use a GPS/GNSS receiver in a wilderness environment.  
4.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
4.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required for an individual to be endorsed for Basic Wilderness GPS/GNSS Use. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
4.6 Though this guide establishes only minimum training, it does not imply that a person endorsed for Basic Wilderness GPS/GNSS Use is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
4.7 This guide can be used to evaluate a document to determine if its content includes the nec...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS2 receiver to determine one’s position, and collect location data, in the wilderness.  
1.2 This guide applies to the use of a GPS/GNSS receiver on land, on and off roads, and on small bodies of water, wherever GPS/GNSS signals can be received.  
1.3 This guide applies to the use of a GPS/GNSS receiver in disaster areas where local positioning aids or references may be lost or damaged.  
1.4 This guide does not apply to the use of a GPS/GNSS receiver on large bodies of water, at sea, or in the air.  
1.5 A person who meets the requirements in this guide is only prepared to operate a GPS/GNSS receiver to determine his or her location, and collect position and movement information, in a wilderness environment.  
1.6 This guide does not imply that a GPS/GNSS receiver is a replacement for a map and compass. Use of the latter is strongly recommended as a backup for GPS/GNSS navigation.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3072-14(2020)(Guide)
Standard Guide for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW) Endorsement

SIGNIFICANCE AND USE
4.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS receiver to navigate in the wilderness. A person trained to this guide shall be endorsed for Intermediate Wilderness GPS/GNSS Use (GPS/GNSS-IIW Endorsed).  
4.1.1 Every person who is endorsed for Intermediate Wilderness GPS/GNSS Use shall have met the requirements of this guide.  
4.2 This guide is the second level of training for wilderness GPS/GNSS use, and only establishes the minimum knowledge, skills, and abilities required for a person to navigate with a GPS/GNSS receiver in a wilderness environment. No other skills are included or implied.  
4.3 In addition to meeting the requirements of this guide, a person endorsed for Intermediate Wilderness GPS/GNSS Use shall also be adequately trained to travel and work in a wilderness environment.  
4.4 Depending on the regulations or policies of the AHJ, additional knowledge, skills, or abilities may be required before a person who meets the requirements in this guide may use a GPS/GNSS receiver to navigate in a wilderness environment.  
4.4.1 Nothing in this guide precludes an AHJ from adding additional requirements for its own members.  
4.5 This guide by itself is not a complete training document. It only specifies the knowledge, skills, and abilities required for an individual to be endorsed for Intermediate Wilderness GPS/GNSS Use. This guide may, however, be used in the development of, or as part of, a complete training document or program.  
4.6 Though this guide establishes only minimum training, it does not imply that a person endorsed for Intermediate Wilderness GPS/GNSS Use is a “trainee,” “probationary,” or other similar term member of an organization. The AHJ is responsible for determining the requirements and qualifications for member or employee ratings.  
4.7 This guide can be used to evaluate a document to determine if its content includes the necessary topics for training a person to be endorsed ...
SCOPE
1.1 This guide establishes the minimum knowledge, skills, and abilities required to use a GPS/GNSS2 receiver to navigate in the wilderness.  
1.2 This guide applies to the use of a GPS/GNSS receiver on land, on and off roads, and on small bodies of water, wherever GPS/GNSS signals can be received.  
1.3 This guide applies to the use of a GPS/GNSS receiver in disaster areas where local positioning aids or references may be lost or damaged.  
1.4 This guide does not apply to the use of a GPS/GNSS receiver on large bodies of water, at sea, or in the air.  
1.5 This guide does not imply that a GPS/GNSS receiver is a replacement for a map and compass. Use of the latter is strongly recommended as a backup for GPS/GNSS navigation.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C1178/C1178M-24(Specification)
Standard Specification for Coated Glass Mat Water-Resistant Gypsum Backing Panel

ABSTRACT
This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile. Coated glass mat water-resistant gypsum backing panel shall consist of a noncombustible water-resistant gypsum core, surfaced with glass mat, partially or completely embedded in the core, and with a water-resistant coating on one surface. The specimens shall be tested for flexural strength, humidified deflection, core hardness, end hardness, edge hardness, nail pull resistance, water resistance, and surface water absorption. Coated glass mat water-resistant gypsum backing panel shall have surfaces true and free of imperfections that render the panel unfit for its designed use.
SCOPE
1.1 This specification covers coated glass mat water-resistant gypsum backing panel designed for use on ceilings and walls in bath and shower areas as a base for the application of ceramic or plastic tile.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Within the text, the SI units are shown in brackets.  
1.3 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2170/D2170M-24(Test Method)
Standard Test Method for Kinematic Viscosity of Asphalts

SIGNIFICANCE AND USE
5.1 The kinematic viscosity characterizes flow behavior. The method is used to determine the consistency of liquid asphalt as one element in establishing the uniformity of shipments or sources of supply. The specifications are usually at temperatures of 60 and 135 °C.
Note 3: The quality of the results produced by this standard are dependent on the competence of the personnel performing the procedure and the capability, calibration, and maintenance of the equipment used. Agencies that meet the criteria of Specification D3666 are generally considered capable of competent and objective testing, sampling, inspection, etc. Users of this standard are cautioned that compliance with Specification D3666 alone does not completely ensure reliable results. Reliable results depend on many factors; following the suggestions of Specification D3666 or some similar acceptable guideline provides a means of evaluating and controlling some of those factors.
SCOPE
1.1 This test method covers procedures for the determination of kinematic viscosity of liquid asphalts, road oils, and distillation residues of liquid asphalts all at 60 °C [140 °F] and of liquid asphalt binders at 135 °C [275 °F] (see table notes, 11.1) in the range from 6 to 100 000 mm2/s [cSt].  
1.2 Results of this test method can be used to calculate viscosity when the density of the test material at the test temperature is known or can be determined. See Annex A1 for the method of calculation.  
Note 1: This test method is suitable for use at other temperatures and at lower kinematic viscosities, but the precision is based on determinations on liquid asphalts and road oils at 60 °C [140 °F] and on asphalt binders at 135 °C [275 °F] only in the viscosity range from 30 to 6000 mm2/s [cSt].
Note 2: Modified asphalt binders or asphalt binders that have been conditioned or recovered are typically non-Newtonian under the conditions of this test. The viscosity determined from this method is under the assumption that asphalt binders behave as Newtonian fluids under the conditions of this test. When the flow is non-Newtonian in a capillary tube, the shear rate determined by this method may be invalid. The presence of non-Newtonian behavior for the test conditions can be verified by measuring the viscosity with viscometers having different-sized capillary tubes. The defined precision limits in 11.1 may not be applicable to non-Newtonian asphalt binders.  
1.3 Warning—Mercury has been designated by the United States Environmental Protection Agency (EPA) and many state agencies as a hazardous material that can cause central nervous system, kidney, and liver damage. Mercury, or its vapor, may be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury-containing products. See the applicable product Material Safety Data Sheet (MSDS) or Safety Data Sheet (SDS) for details and the EPA’s website—http://www.epa.gov/mercury/faq.htm—for additional information. Users should be aware that selling mercury, mercury-containing products, or both, in your state may be prohibited by state law.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 The text of this standard references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior ...

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D6356/D6356M-98(2024)(Test Method)
Standard Test Method for Hydrogen Gas Generation of Aluminum Emulsified Asphalt Used as a Protective Coating for Roofing

SIGNIFICANCE AND USE
4.1 This procedure measures the amount of hydrogen gas generation potential of aluminized emulsion roof coating. There is the possibility of water reacting with aluminum pigment to generate hydrogen gas. This situation is to be avoided, so this test was designed to evaluate coating formulations and assess the propensity to gassing.
SCOPE
1.1 This test method covers a hydrogen gas and stability test for aluminum emulsified asphalt coatings.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D5643/D5643M-06(2024)(Specification)
Standard Specification for Coal Tar Roof Cement, Asbestos Free

ABSTRACT
This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems. The chemical composition of coal tar roof cement shall conform to the requirements prescribed. The water, non-volatile matter, insoluble matter, behaviour at 60 deg. C, adhesion to wet surfaces, and flash point shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification covers coal tar roof cement suitable for trowel application in coal tar roofing and flashing systems.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM C363/C363M-16(2024)(Test Method)
Standard Test Method for Node Tensile Strength of Honeycomb Core Materials

SIGNIFICANCE AND USE
5.1 The honeycomb tensile-node bond strength is a fundamental property than can be used in determining whether honeycomb cores can be handled during cutting, machining and forming without the nodes breaking. The tensile-node bond strength is the tensile stress that causes failure of the honeycomb by rupture of the bond between the nodes. It is usually a peeling-type failure.  
5.2 This test method provides a standard method of obtaining tensile-node bond strength data for quality control, acceptance specification testing, and research and development.
SCOPE
1.1 This test method covers the determination of the tensile-node bond strength of honeycomb core materials.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1894-24(Guide)
Standard Guide for Selecting Dosimetry Systems for Application in Pulsed X-Ray Sources

SIGNIFICANCE AND USE
4.1 Flash X-ray facilities provide intense bremsstrahlung radiation environments, usually in a single sub-microsecond pulse, which often fluctuates in amplitude, shape, and spectrum from shot to shot. Therefore, appropriate dosimetry must be fielded on every exposure to characterize the environment, see ICRU Report 34. These intense bremsstrahlung sources have a variety of applications which include the following:
(1) Studies of the effects of X-rays and gamma rays on materials.
(2) Studies of the effects of radiation on electronic devices such as transistors, diodes, and capacitors.
(3) Computer code validation studies.  
4.2 This guide is written to assist the experimenter in selecting the needed dosimetry systems for use at pulsed X-ray facilities. This guide also provides a brief summary on how to use each of the dosimetry systems. Other guides (see Section 2) provide more detailed information on selected dosimetry systems in radiation environments and should be consulted after an initial decision is made on the appropriate dosimetry system to use. There are many key parameters which describe a flash X-ray source, such as dose, dose rate, spectrum, pulse width, etc., such that typically no single dosimetry system can measure all the parameters simultaneously. However, it is frequently the case that not all key parameters must be measured in a given experiment.
SCOPE
1.1 This guide provides assistance in selecting and using dosimetry systems in flash X-ray experiments. Both dose and dose rate techniques are described.  
1.2 Operating characteristics of flash X-ray sources are given, with emphasis on the spectrum of the photon output.  
1.3 Assistance is provided to relate the measured dose to the response of a device under test (DUT). The device is assumed to be a semiconductor electronic part or system.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    19 pages
    English language
    sale 15% off
  • Guide
    19 pages
    English language
    sale 15% off