iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM G1-03(2011)

(Practice)

Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens

Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens

SIGNIFICANCE AND USE
The procedures given are designed to remove corrosion products without significant removal of base metal. This allows an accurate determination of the mass loss of the metal or alloy that occurred during exposure to the corrosive environment.
These procedures, in some cases, may apply to metal coatings. However, possible effects from the substrate must be considered.
SCOPE
1.1 This practice covers suggested procedures for preparing bare, solid metal specimens for tests, for removing corrosion products after the test has been completed, and for evaluating the corrosion damage that has occurred. Emphasis is placed on procedures related to the evaluation of corrosion by mass loss and pitting measurements. (WarningIn many cases the corrosion product on the reactive metals titanium and zirconium is a hard and tightly bonded oxide that defies removal by chemical or ordinary mechanical means. In many such cases, corrosion rates are established by mass gain rather than mass loss.)
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 1.1 and 7.2.

General Information

Status
Historical
Publication Date
30-Nov-2011
ICS
77.060 - Corrosion of metals
Technical Committee
G01 - Corrosion of Metals
Drafting Committee
G01.05 - Laboratory Corrosion Tests
Current Stage
Ref Project

Relations

Replaces
ASTM G1-03 - Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
Effective Date
01-Dec-2011
Referred By
ASTM G67-18 - Standard Test Method for Determining the Susceptibility to Intergranular Corrosion of 5XXX Series Aluminum Alloys by Mass Loss After Exposure to Nitric Acid (NAMLT Test)
Effective Date
01-Dec-2011
Referred By
ASTM G111-21a - Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both
Effective Date
01-Dec-2011
Referred By
ASTM G170-06(2020)e1 - Standard Guide for Evaluating and Qualifying Oilfield and Refinery Corrosion Inhibitors in the Laboratory
Effective Date
01-Dec-2011
Referred By
ASTM C1187-20a - Standard Guide for Establishing Surveillance Test Program for Boron-based Neutron Absorbing Material Systems for Use in Nuclear Fuel Storage Racks in Pool Environment
Effective Date
01-Dec-2011
Referred By
ASTM G110-92(2022)e2 - Standard Practice for Evaluating Intergranular Corrosion Resistance of Heat Treatable Aluminum Alloys by Immersion in Sodium Chloride + Hydrogen Peroxide Solution
Effective Date
01-Dec-2011
Referred By
ASTM G46-21 - Standard Guide for Examination and Evaluation of Pitting Corrosion
Effective Date
01-Dec-2011
Referred By
ASTM G101-04(2020) - Standard Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
Effective Date
01-Dec-2011
Referred By
ASTM B895-16(2020)e1 - Standard Test Methods for Evaluating the Corrosion Resistance of Stainless Steel Powder Metallurgy (PM) Parts/Specimens by Immersion in a Sodium Chloride Solution
Effective Date
01-Dec-2011
Referred By
ASTM G185-06(2020)e1 - Standard Practice for Evaluating and Qualifying Oil Field and Refinery Corrosion Inhibitors Using the Rotating Cylinder Electrode
Effective Date
01-Dec-2011
Referred By
ASTM G198-17 - Standard Test Method for Determining the Relative Corrosion Performance of Driven Fasteners in Contact with Treated Wood
Effective Date
01-Dec-2011
Referred By
ASTM D2688-15e1 - Standard Test Method for Corrosivity of Water in the Absence of Heat Transfer (Weight Loss Method)
Effective Date
01-Dec-2011
Referred By
ASTM G78-20 - Standard Guide for Crevice Corrosion Testing of Iron-Base and Nickel-Base Stainless Alloys in Seawater and Other Chloride-Containing Aqueous Environments
Effective Date
01-Dec-2011
Referred By
ASTM G96-90(2018) - Standard Guide for Online Monitoring of Corrosion in Plant Equipment (Electrical and Electrochemical Methods)
Effective Date
01-Dec-2011
Referred By
ASTM G150-18 - Standard Test Method for Electrochemical Critical Pitting Temperature Testing of Stainless Steels and Related Alloys
Effective Date
01-Dec-2011

Buy Standard

ASTM G1-03(2011) - Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test SpecimensASTM G1-03(2011) - Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
PreviousNext
Standard
ASTM G1-03(2011) - Standard Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
English language
9 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: G1 − 03 (Reapproved 2011)
Standard Practice for
Preparing, Cleaning, and Evaluating Corrosion Test
1
Specimens
ThisstandardisissuedunderthefixeddesignationG1;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D2776Methods of Test for Corrosivity of Water in the
Absence of Heat Transfer (Electrical Methods) (With-
1.1 This practice covers suggested procedures for preparing
3
drawn 1991)
bare, solid metal specimens for tests, for removing corrosion
G15TerminologyRelatingtoCorrosionandCorrosionTest-
products after the test has been completed, and for evaluating
3
ing (Withdrawn 2010)
thecorrosiondamagethathasoccurred.Emphasisisplacedon
G16Guide for Applying Statistics to Analysis of Corrosion
procedures related to the evaluation of corrosion by mass loss
Data
and pitting measurements. (Warning—In many cases the
G31Guide for Laboratory Immersion Corrosion Testing of
corrosion product on the reactive metals titanium and zirco-
Metals
nium is a hard and tightly bonded oxide that defies removal by
G33Practice for Recording Data from Atmospheric Corro-
chemical or ordinary mechanical means. In many such cases,
sion Tests of Metallic-Coated Steel Specimens
corrosion rates are established by mass gain rather than mass
G46Guide for Examination and Evaluation of Pitting Cor-
loss.)
rosion
1.2 The values stated in SI units are to be regarded as
G50Practice for Conducting Atmospheric Corrosion Tests
standard. No other units of measurement are included in this
on Metals
standard.
G78Guide for Crevice Corrosion Testing of Iron-Base and
1.3 This standard does not purport to address all of the
Nickel-Base Stainless Alloys in Seawater and Other
safety concerns, if any, associated with its use. It is the Chloride-Containing Aqueous Environments
responsibility of the user of this standard to establish appro-
3. Terminology
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. For specific
3.1 See Terminology G15 for terms used in this practice.
warning statements, see 1.1 and 7.2.
4. Significance and Use
2. Referenced Documents
4.1 The procedures given are designed to remove corrosion
2
2.1 ASTM Standards: productswithoutsignificantremovalofbasemetal.Thisallows
A262Practices for Detecting Susceptibility to Intergranular anaccuratedeterminationofthemasslossofthemetaloralloy
Attack in Austenitic Stainless Steels that occurred during exposure to the corrosive environment.
D1193Specification for Reagent Water
4.2 These procedures, in some cases, may apply to metal
D1384Test Method for Corrosion Test for Engine Coolants
coatings. However, possible effects from the substrate must be
in Glassware
considered.
5. Reagents and Materials
1
This practice is under the jurisdiction ofASTM Committee G01 on Corrosion
of Metals and is the direct responsibility of Subcommittee G01.05 on Laboratory
5.1 Purity of Reagents—Reagent grade chemicals shall be
Corrosion Tests.
used in all tests. Unless otherwise indicated, it is intended that
Current edition approved Dec. 1, 2011. Published April 2012. Originally
all reagents conform to the specifications of the Committee on
approved in 1967. Last previous edition approved in 2003 as G1–2003. DOI:
10.1520/G0001-03R11. Analytical Reagents of theAmerican Chemical Society where
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on
the ASTM website. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
G1 − 03 (2011)
4
such specifications are available. Other grades may be used, 6.3 For more searching tests of either the metal or the
provided it is first ascertained that the reagent is of sufficiently environment, standard surface finishes may be preferred. A
high purity to permit its use without lessening the accuracy of suitable procedure might be:
the determination. 6.3.1 Degreaseinanorganicsolventorhotalkalinecleaner.
(See also Practice G31.)
5.2 Purity of Water—Unless otherwise indicated, references
to water shall be understood to mean reagent water as defined
NOTE1—Hotalkaliesandchlorinatedsolventsmayattacksomemetals.
NOTE 2—Ultrasonic cleaning may be beneficial in both pre-test and
by Type IV of Specification D1193.
post-test cleaning procedures.
6. Methods for Preparing Specimens for Te
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM G49-85(2023)e1(Practice)
Standard Practice for Preparation and Use of Direct Tension Stress-Corrosion Test Specimens

SIGNIFICANCE AND USE
4.1 Axially loaded tension specimens provide one of the most versatile methods of performing a stress-corrosion test because of the flexibility permitted in the choice of type and size of test specimen, stressing procedures, and range of stress levels.  
4.2 The uniaxial stress system is simple; hence, this test method is often used for studies of stress-corrosion mechanisms. This type of test is amenable to the simultaneous exposure of unstressed specimens (no applied load) with stressed specimens and subsequent tension testing to distinguish between the effects of true stress corrosion and mechanical overload (2). Additional considerations in regard to the significance of the test results and their interpretation are given in Sections 6 and 10.  
4.3 Wide variations in test results may be obtained for a given material and specimen orientation with different specimen sizes and stressing procedures. This consideration is significant especially in the standardization of a test procedure for interlaboratory comparisons or quality control.
SCOPE
1.1 This practice covers procedures for designing, preparing, and using ASTM standard tension test specimens for investigating susceptibility to stress-corrosion cracking. Axially loaded specimens may be stressed quantitatively with equipment for application of either a constant load, constant strain, or with a continuously increasing strain.  
1.2 Tension test specimens are adaptable for testing a wide variety of product forms as well as parts joined by welding, riveting, or various other methods.  
1.3 The exposure of specimens in a corrosive environment is treated only briefly because other standards are being prepared to deal with this aspect. Meanwhile, the investigator is referred to Practices G35, G36, G37, and G44, and to ASTM Special Technical Publication 425 (1).2  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM G87-02(2023)(Practice)
Standard Practice for Conducting Moist SO2 Tests

SIGNIFICANCE AND USE
3.1 Moist air containing sulfur dioxide quickly produces easily visible corrosion on many metals in a form resembling that occurring in industrial environments. It is therefore a test medium well suited to detect pores or other sources of weakness in protective coatings and deficiencies in corrosion resistance associated with unsuitable alloy composition or treatments.  
3.2 The results obtained in the test should not be regarded as a general guide to the corrosion resistance of the tested materials in all environments where these materials may be used. Performance of different materials in the test should only be taken as a general guide to the relative corrosion resistance of these materials in moist SO2 service.
SCOPE
1.1 This practice covers the apparatus and procedure to be used in conducting qualitative assessment tests in accordance with the requirements of material or product specifications by means of specimen exposure to condensed moisture containing sulfur dioxide.  
1.2 The exposure conditions may be varied to suit particular requirements and this practice includes provisions for use of different concentrations of sulfur dioxide and for tests either running continuously or in cycles of alternate exposure to the sulfur dioxide containing atmosphere and to the ambient atmosphere.  
1.3 The variant of the test to be used, the exposure period required, the type of test specimen, and the criteria of failure are not prescribed by this practice. Such details are provided in appropriate material and product purchase specifications.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For a specific warning statement, see 4.3.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM G35-23(Practice)
Standard Practice for Determining the Susceptibility of Stainless Steels and Related Nickel-Chromium-Iron Alloys to Stress-Corrosion Cracking in Polythionic Acids

SIGNIFICANCE AND USE
4.1 Polythionic acids are chemically described as H2SxO6, where x is usually 3, 4, or 5 (1)3 though can be more than 50 (2). These acid environments provide a way of evaluating the resistance of stainless steels and related alloys to intergranular stress corrosion cracking. Failure is accelerated by the presence of increasing amounts of intergranular precipitate. Results for the polythionic acid test have not been correlated exactly with those of intergranular corrosion tests (Test Methods G28). Also, this test may not be relevant to stress corrosion cracking in chlorides or caustic environments.  
4.2 The polythionic acid environment may produce areas of shallow intergranular attack in addition to the more localized and deeper cracking mode of attack. Examination of failed specimens is necessary to confirm that failure occurred by cracking rather than mechanical failure of reduced sections.
SCOPE
1.1 This practice covers procedures for preparing and conducting the polythionic acid test at room temperature, 22 °C to 25 °C (72 °F to 77 °F), to determine the relative susceptibility of stainless steels or other related materials (nickel-chromium-iron alloys) to intergranular stress corrosion cracking.  
1.2 This practice can be used to evaluate stainless steels or other materials in the “as received” condition or after being subjected to high-temperature service, 482 °C to 815 °C (900 °F to 1500 °F), for prolonged periods of time.  
1.3 This practice can be applied to wrought products, castings, and weld metal of stainless steels or other related materials to be used in environments containing sulfur or sulfides. Other materials capable of being sensitized can also be tested in accordance with this test.  
1.4 This practice may be used with a variety of stress corrosion test specimens, surface finishes, and methods of applying stress.  
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For more specific precautionary statements, see Section 7.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM G102-23(Practice)
Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements

SIGNIFICANCE AND USE
3.1 Electrochemical corrosion rate measurements often provide results in terms of electrical current. Although the conversion of these current values into mass loss rates or penetration rates is based on Faraday’s Law, the calculations can be complicated for alloys and metals with elements having multiple valence values. This practice is intended to provide guidance in calculating mass loss and penetration rates for such alloys. Some typical values of equivalent weights for a variety of metals and alloys are provided.  
3.2 Electrochemical corrosion rate measurements may provide results in terms of electrical resistance. The conversion of these results to either mass loss or penetration rates requires additional electrochemical information. Some approaches for estimating this information are given.  
3.3 Use of this practice will aid in producing more consistent corrosion rate data from electrochemical results. This will make results from different studies more comparable and minimize calculation errors that may occur in transforming electrochemical results to corrosion rate values.
SCOPE
1.1 This practice covers the providing of guidance in converting the results of electrochemical measurements to rates of uniform corrosion. Calculation methods for converting corrosion current density values to either mass loss rates or average penetration rates are given for most engineering alloys. In addition, some guidelines for converting polarization resistance values to corrosion rates are provided.  
1.2 The values stated in SI units are to be regarded as standard. Other units of measurement are included in this standard because of their usage.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM G123-00(2022)e1(Test Method)
Standard Test Method for Evaluating Stress-Corrosion Cracking of Stainless Alloys with Different Nickel Content in Boiling Acidified Sodium Chloride Solution

SIGNIFICANCE AND USE
5.1 This test method is designed to compare alloys and may be used as one method of screening materials prior to service. In general, this test method is more useful for stainless steels than the boiling magnesium chloride test of Practice G36. The boiling magnesium chloride test cracks materials with the nickel levels found in relatively resistant austenitic and duplex stainless steels, thus making comparisons and evaluations for many service environments difficult.  
5.2 This test method is intended to simulate cracking in water, especially cooling waters that contain chloride. It is not intended to simulate cracking that occurs at high temperatures (greater than 200 °C or 390 °F) with chloride or hydroxide.
Note 1: The degree of cracking resistance found in full-immersion tests may not be indicative of that for some service conditions comprising exposure to the water-line or in the vapor phase where chlorides may concentrate.  
5.3 Correlation with service experience should be obtained when possible. Different chloride environments may rank materials in a different order.  
5.4 In interlaboratory testing, this test method cracked annealed UNS S30400 and S31600 but not more resistant materials, such as annealed duplex stainless steels or higher nickel alloys, for example, UNS N08020 (for example 20Cb-33 stainless). These more resistant materials are expected to crack when exposed to Practice G36 as U-bends. Materials which withstand this sodium chloride test for a longer period than UNS S30400 or S31600 may be candidates for more severe service applications.  
5.5 The repeatability and reproducibility data from Section 12 and Appendix X1 must be considered prior to use. Interlaboratory variation in results may be expected as occurs with many corrosion tests. Acceptance criteria are not part of this test method and if needed are to be negotiated by the user and the producer.
SCOPE
1.1 This test method covers a procedure for conducting stress-corrosion cracking tests in an acidified boiling sodium chloride solution. This test method is performed in 25 % (by mass) sodium chloride acidified to pH 1.5 with phosphoric acid. This test method is concerned primarily with the test solution and glassware, although a specific style of U-bend test specimen is suggested.  
1.2 This test method is designed to provide better correlation with chemical process industry experience for stainless steels than the more severe boiling magnesium chloride test of Practice G36. Some stainless steels which have provided satisfactory service in many environments readily crack in Practice G36, but have not cracked during interlaboratory testing (see Section 12) using this sodium chloride test method.  
1.3 This boiling sodium chloride test method was used in an interlaboratory test program to evaluate wrought stainless steels, including duplex (ferrite-austenite) stainless and an alloy with up to about 33 % nickel. It may also be employed to evaluate these types of materials in the cast or welded conditions.  
1.4 This test method detects major effects of composition, heat treatment, microstructure, and stress on the susceptibility of materials to chloride stress-corrosion cracking. Small differences between samples such as heat-to-heat variations of the same grade are not likely to be detected.  
1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.  
1.7 This international standard was developed in accordance with internationally recogni...

  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM G30-22(Practice)
Standard Practice for Making and Using U-Bend Stress-Corrosion Test Specimens

SIGNIFICANCE AND USE
5.1 The U-bend specimen may be used for any metal alloy sufficiently ductile to be formed into the U-shape without mechanically cracking. The specimen is most easily made from strip or sheet but can be machined from plate, bar, castings, or weldments; wire specimens may be used also.  
5.2 Since the U-bend usually contains large amounts of elastic and plastic strain, it provides one of the most severe tests available for smooth (as opposed to notched or precracked) stress-corrosion test specimens. The stress conditions are not usually known and a wide range of stresses exist in a single stressed specimen. The specimen is therefore unsuitable for studying the effects of different applied stresses on stress-corrosion cracking or for studying variables that have only a minor effect on cracking. The advantage of the U-bend specimen is that it is simple and economical to make and use. It is most useful for detecting large differences between the stress-corrosion cracking resistance of (a) different metals in the same environment, (b) one metal in different metallurgical conditions in the same environment, or (c) one metal in several environments.
SCOPE
1.1 This practice covers procedures for making and using U-bend specimens for the evaluation of stress-corrosion cracking in metals. The U-bend specimen is generally a rectangular strip that is bent 180° around a predetermined radius and maintained in this constant strain condition during the stress-corrosion test. Bends slightly less than or greater than 180° are sometimes used. Typical U-bend configurations showing several different methods of maintaining the applied stress are shown in Fig. 1.  
FIG. 1 Typical Stressed U-bends  
1.2 U-bend specimens usually contain both elastic and plastic strain. In some cases (for example, very thin sheet or small diameter wire) it is possible to form a U-bend and produce only elastic strain. However, bent-beam (Practice G39 or direct tension (Practice G49)) specimens are normally used to study stress-corrosion cracking of strip or sheet under elastic strain only.  
1.3 This practice is concerned only with the test specimen and not the environmental aspects of stress-corrosion testing, which are discussed elsewhere (1)2 and in Practices G35, G36, G37, G41, G44, G103 and Test Method G123.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM G111-21a(Guide)
Standard Guide for Corrosion Tests in High Temperature or High Pressure Environment, or Both

SIGNIFICANCE AND USE
5.1 Autoclave tests are commonly used to evaluate the corrosion performance of metallic and non-metallic materials under simulated HP and HTHP service conditions. Examples of service environments in which HP and HTHP corrosion tests have been used include chemical processing, petroleum production and refining, food processing, pressurized cooling water, electric power systems, and aerospace propulsion.  
5.2 For the applications of corrosion testing listed in 5.1, the service environment involves handling corrosive and potentially hazardous media under conditions of high pressure or high temperature, or both. The temperature and pressure, among other parameters, usually drive the composition and properties of the aqueous phase and, hence, the severity of the corrosion process. Consequently, the laboratory evaluation of corrosion severity cannot be performed in conventional low pressure glassware without making potentially invalid assumptions as to the potential effects of high temperature and pressure on corrosion severity.  
5.3 Therefore, there is a substantial need to provide standardized methods by which corrosion testing can be performed under HP and HTHP. In many cases, however, the standards used for exposure of specimens in conventional low-pressure glassware experiments cannot be followed due to the limitations of access, volume, and visibility arising from the construction of high-pressure test cells. This guide refers to existing corrosion standards and practices, as applicable, and then goes further in areas in which specific guidelines for performing HP and HTHP corrosion testing are needed.
SCOPE
1.1 This guide covers procedures, specimens, and equipment for conducting laboratory corrosion tests on metallic materials under conditions of high pressure (HP) or the combination of high temperature and high pressure (HTHP). See 3.2 for definitions of high pressure and temperature.  
1.2 The procedures and methods in this guide are applicable for conducting mass loss corrosion, localized corrosion, and electrochemical tests as well as for use in environmentally induced cracking tests that need to be conducted under HP or HTHP conditions.  
1.3 The primary purpose for this guide is to promote consistency of corrosion test results. Furthermore, this guide will aid in the comparison of corrosion data between laboratories or testing organizations that utilize different equipment.  
1.4 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM G46-21(Guide)
Standard Guide for Examination and Evaluation of Pitting Corrosion

SIGNIFICANCE AND USE
4.1 It is important to be able to determine the extent of pitting, either in a service application in which it is necessary to predict the remaining life in a metal structure, or in laboratory test programs that are used to select the most pitting-resistant materials for service. The purpose of the study is crucial in determining the appropriate examination and evaluation steps.  
4.2 Some typical purposes of laboratory tests include, but are not limited to, evaluating performance of alloys, determining whether an alloy is resistant to the environment, evaluating how environmental conditions including corrosion inhibitor affect or prevent pitting, and evaluating whether a lot of metal is sufficiently resistant for its use in a particular application or environment.  
4.3 Some typical purposes of field studies include, but are not limited to, determining if pits are likely to grow and cause leak or release of process fluid, and assisting a determination of whether to replace or repair damage from pits (remaining life assessment).
SCOPE
1.1 This guide covers the selection of procedures that can be used in the examination and evaluation of pitted metals. These procedures include both nondestructive and destructive approaches.  
1.2 The procedures covered in this guide include those that may be used in laboratory evaluations of corroded metal specimens and field examinations and inspections.  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3.1 Exception—In X1.2.1, mils per year (MPY) are regarded as standard for the target corrosion rate.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    13 pages
    English language
    sale 15% off
  • Guide
    13 pages
    English language
    sale 15% off
ASTM
ASTM G37-98(2021)(Practice)
Standard Practice for Use of Mattsson's Solution of pH 7.2 to Evaluate the Stress-Corrosion Cracking Susceptibility of Copper-Zinc Alloys

SIGNIFICANCE AND USE
4.1 This test environment is believed to give an accelerated ranking of the relative or absolute degree of stress-corrosion cracking susceptibility for different brasses. It has been found to correlate well with the corresponding service ranking in environments that cause stress-corrosion cracking which is thought to be due to the combined presence of traces of moisture and ammonia vapor. The extent to which the accelerated ranking correlates with the ranking obtained after long-term exposure to environments containing corrodents other than ammonia is not at present known. Examples of such environments may be severe marine atmospheres (Cl−), severe industrial atmospheres (predominantly SO2), and super-heated ammonia-free steam.  
4.2 It is not possible at present to specify any particular time to failure (defined on the basis of any particular failure criteria) in pH 7.2 Mattsson’s solution that corresponds to a distinction between acceptable and unacceptable stress-corrosion behavior in brass alloys. Such particular correlations must be determined individually.  
4.3 Mattsson's solution of pH 7.2 may also cause stress independent general and intergranular corrosion of brasses to some extent. This leads to the possibility of confusing stress-corrosion failures with mechanical failures induced by corrosion-reduced net cross sections. This danger is particularly great with small cross section specimens, high applied stress levels, long exposure periods and stress-corrosion resistant alloys. Careful metallographic examination is recommended for correct diagnosis of the cause of failure. Alternatively, unstressed control specimens may be exposed to evaluate the extent to which stress independent corrosion degrades mechanical properties.
SCOPE
1.1 This practice covers the preparation and use of Mattsson’s solution of pH 7.2 as an accelerated stress-corrosion cracking test environment for brasses (copper-zinc base alloys). The variables (to the extent that these are known at present) that require control are described together with possible means for controlling and standardizing these variables.  
1.2 This practice is recommended only for brasses (copper-zinc base alloys). The use of this test environment is not recommended for other copper alloys since the results may be erroneous, providing completely misleading rankings. This is particularly true of alloys containing aluminum or nickel as deliberate alloying additions.  
1.3 This practice is intended primarily where the test objective is to determine the relative stress-corrosion cracking susceptibility of different brasses under the same or different stress conditions or to determine the absolute degree of stress corrosion cracking susceptibility, if any, of a particular brass or brass component under one or more specific stress conditions. Other legitimate test objectives for which this test solution may be used do, of course, exist. The tensile stresses present may be known or unknown, applied or residual. The practice may be applied to wrought brass products or components, brass castings, brass weldments, and so forth, and to all brasses. Strict environmental test conditions are stipulated for maximum assurance that apparent variations in stress-corrosion susceptibility are attributable to real variations in the material being tested or in the tensile stress level and not to environmental variations.  
1.4 This practice relates solely to the preparation and control of the test environment. No attempt is made to recommend surface preparation or finish, or both, as this may vary with the test objectives. Similarly, no attempt is made to recommend particular stress-corrosion test specimen configurations or methods of applying the stress. Test specimen configurations that may be used are referenced in Practice G30 and STP 425.2  
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included ...

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM G186-05(2021)(Test Method)
Standard Test Method for Determining Whether Gas-Leak-Detector Fluid Solutions Can Cause Stress Corrosion Cracking of Brass Alloys

SIGNIFICANCE AND USE
5.1 Brass components are routinely used in compressed gas service for valves, pressure regulators, connectors and many other components. Although soft brass is not susceptible to ammonia SCC, work-hardened brass is susceptible if its hardness exceeds about 54 HR 30T (55HRB) (Rockwell scale). Normal assembly of brass components should not induce sufficient work hardening to cause susceptibility to ammonia SCC. However, it is has been observed that over-tightening of the components will render them susceptible to SCC, and the problem becomes more severe in older components that have been tightened many times. In this test, the specimens are obtained in the hardened condition and are strained beyond the elastic limit to accelerate the tendency towards SCC.  
5.2 It is normal practice to use LDFs to check pressurized systems to assure that leaking is not occurring. LDFs are usually aqueous solutions containing surfactants that will form bubbles at the site of a leak. If the LDF contains ammonia or other agent that can cause SCC in brass, serious damage can occur to the system that will compromise its safety and integrity.  
5.3 It is important to test LDFs to assure that they do not cause SCC of brass and to assure that the use of these products does not compromise the integrity of the pressure containing system.  
5.4 It has been found that corrosion of brass is necessary before SCC can occur. The reason for this is that the corrosion process results in cupric and cuprous ions accumulating in the electrolyte. Therefore, adding copper metal and cuprous oxide (Cu2O) to the aqueous solution accelerates the SCC process if agents that cause SCC are present. However, adding these components to a solution that does not cause SCC will not make stressed brass crack.  
5.5 Repeated application of the solution to the specimen followed by a drying period causes the components in the solution to concentrate thereby further increasing the rate of cracking. This also simulates se...
SCOPE
1.1 This test method covers an accelerated test method for evaluating the tendency of gas leak detection fluids (LDFs) to cause stress corrosion cracking (SCC) of brass components in compressed gas service.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    10 pages
    English language
    sale 15% off