ASTM C1697-18

Standard Specification for Blended Supplementary Cementitious Materials

SCOPE
1.1 This specification covers blended supplementary cementitious materials that result from the blending or intergrinding of two or three ASTM compliant supplementary cementitious materials, for use in concrete or mortar where hydraulic or pozzolanic action, or both, is desired. The supplementary cementitious materials include slag cement conforming to Specification C989/C989M, natural pozzolans and coal fly ash conforming to Specification C618 and silica fume conforming to Specification C1240.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: The incorporation of supplementary cementitious materials as separate additions or as a manufactured blend may significantly alter the properties of fresh and hardened concrete. The user should be aware of these changes and is referred to the ACI Manual of Concrete Practice2 for information and guidelines. Specific reference is made to:    
ACI 232.1R  
Use of Natural Pozzolans in Concrete  
ACI 232.2R  
Use of Fly Ash in Concrete  
ACI 233R  
Slag Cement in Concrete and Mortar  
ACI 234R  
Guide for the Use of Silica Fume in Concrete  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 30-Nov-2018
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: C09 - Concrete and Concrete Aggregates
• Drafting Committee: C09.24 - Supplementary Cementitious Materials

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C1697 −18
Standard Specification for
1
Blended Supplementary Cementitious Materials
This standard is issued under the fixed designation C1697; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
3
1.1 This specification covers blended supplementary ce- 2.1 ASTM Standards:
mentitiousmaterialsthatresultfromtheblendingorintergrind- C114 Test Methods for Chemical Analysis of Hydraulic
ing of two or three ASTM compliant supplementary cementi- Cement
tious materials, for use in concrete or mortar where hydraulic C125 Terminology Relating to Concrete and Concrete Ag-
or pozzolanic action, or both, is desired. The supplementary gregates
cementitious materials include slag cement conforming to C150/C150M Specification for Portland Cement
Specification C989/C989M, natural pozzolans and coal fly ash C151/C151M Test Method for Autoclave Expansion of Hy-
conforming to Specification C618 and silica fume conforming draulic Cement
to Specification C1240. C183/C183M Practice for Sampling and the Amount of
Testing of Hydraulic Cement
1.2 The values stated in SI units are to be regarded as
C311/C311M Test Methods for Sampling and Testing Fly
standard. No other units of measurement are included in this
Ash or Natural Pozzolans for Use in Portland-Cement
standard.
Concrete
NOTE 1—The incorporation of supplementary cementitious materials as
C618 Specification for Coal Fly Ash and Raw or Calcined
separate additions or as a manufactured blend may significantly alter the
properties of fresh and hardened concrete. The user should be aware of
Natural Pozzolan for Use in Concrete
2
these changes and is referred to the ACI Manual of Concrete Practice for
C989/C989M Specification for Slag Cement for Use in
information and guidelines. Specific reference is made to:
Concrete and Mortars
ACI 232.1R Use of Natural Pozzolans in Concrete
C1240 Specification for Silica Fume Used in Cementitious
ACI 232.2R Use of Fly Ash in Concrete
Mixtures
ACI 233R Slag Cement in Concrete and Mortar
ACI 234R Guide for the Use of Silica Fume in Concrete
1.3 This standard does not purport to address all of the 3. Terminology
safety concerns, if any, associated with its use. It is the
3.1 Definitions:
responsibility of the user of this standard to establish appro-
3.1.1 For definitions of other terms used in this
priate safety, health, and environmental practices and deter-
specification, refer to Terminology C125.
mine the applicability of regulatory limitations prior to use.
3.2 Definitions of Terms Specific to This Standard:
1.4 This international standard was developed in accor-
3.2.1 slag cement, n—granulated blast furnace slag that is
dance with internationally recognized principles on standard-
ground to cement fineness with or without additions and meets
ization established in the Decision on Principles for the
Specification C989/C989M.
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical 3.2.2 supplementary cementitious material, n—a slag ce-
ment or pozzolan that contributes to the properties of concrete
Barriers to Trade (TBT) Committee.
or mortar through hydraulic or pozzolanic activity, or both.
1
3.2.3 silica fume, n—as defined in Specification C1240.
This specification is under the jurisdiction of ASTM Committee C09 on
Concrete and ConcreteAggregates and is the direct responsibility of Subcommittee
C09.24 on Supplementary Cementitious Materials.
Current edition approved Dec. 1, 2018. Published February 2019. Originally
3
approved in 2010. Last previous edition approved in 2016 as C1697 – 16. DOI: For referenced ASTM standards, visit the ASTM website, www.astm.org, or
10.1520/C1697-18. contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
2
Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington Standards volume information, refer to the standard’s Document Summary page on
Hills, MI 48333-9094, http://www.concrete.org. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1697−18
4. Classification 5.1.2 The composition of the blend using the naming
convention in 4.2.
4.1 This specification applies to a hydraulic or pozzolanic
5.1.3 Any optional requirements as delineated in Table 2.
material composed of a blend of multiple supplementary
NOTE 3—In advance of ordering, it is important to check for market
cementitious
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1697 − 16 C1697 − 18
Standard Specification for
1
Blended Supplementary Cementitious Materials
This standard is issued under the fixed designation C1697; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers blended supplementary cementitious materials that result from the blending or intergrinding of two
or three ASTM compliant supplementary cementitious materials, for use in concrete or mortar where hydraulic or pozzolanic
action, or both, is desired. The supplementary cementitious materials include slag cement conforming to Specification
C989/C989M, natural pozzolans and coal fly ash conforming to Specification C618 and silica fume conforming to Specification
C1240.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
NOTE 1—The incorporation of supplementary cementitious materials as separate additions or as a manufactured blend may significantly alter the
2
properties of fresh and hardened concrete. The user should be aware of these changes and is referred to the ACI Manual of Concrete Practice for
information and guidelines. Specific reference is made to:
ACI 232.1R Use of Natural Pozzolans in Concrete
ACI 232.2R Use of Fly Ash in Concrete
ACI 233R Slag Cement in Concrete and Mortar
ACI 234R Guide for the Use of Silica Fume in Concrete
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
C114 Test Methods for Chemical Analysis of Hydraulic Cement
C125 Terminology Relating to Concrete and Concrete Aggregates
C150/C150M Specification for Portland Cement
C151/C151M Test Method for Autoclave Expansion of Hydraulic Cement
C183/C183M Practice for Sampling and the Amount of Testing of Hydraulic Cement
C311/C311M Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete
C618 Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
C989/C989M Specification for Slag Cement for Use in Concrete and Mortars
C1240 Specification for Silica Fume Used in Cementitious Mixtures
3. Terminology
3.1 Definitions:
3.1.1 For definitions of other terms used in this specification, refer to Terminology C125.
1
This specification is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.24 on
Supplementary Cementitious Materials.
Current edition approved Oct. 1, 2016Dec. 1, 2018. Published October 2016February 2019. Originally approved in 2010. Last previous edition approved in 20102016 as
C1697C1697 – 16.-10. DOI: 10.1520/C1697-16.10.1520/C1697-18.
2
Available from American Concrete Institute (ACI), P.O. Box 9094, Farmington Hills, MI 48333-9094, http://www.concrete.org.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C1697 − 18
3.2 Definitions of Terms Specific to This Standard:
3.2.1 slag cement, n—granulated blast furnace slag that is ground to cement fineness with o
...