ASTM D580/D580M-10
(Specification)Standard Specification for Greige Woven Glass Tapes and Webbings
Standard Specification for Greige Woven Glass Tapes and Webbings
ABSTRACT
This specification primarily covers greige tapes and webbings woven from "E" electrical classification glass fiber yarns. This specification can also be applied to tapes and webbings made of other glass fiber grades upon agreement between the purchaser and the supplier. Greige glass fiber tapes and webbings are produced in two types: type A - medium texture, and type B - open texture. The fabric count, yarn number, filament diameter, strand construction, twist direction, twist level, weave type, length per unit mass, thickness, breaking force, width, length, ignition loss, and visual appearance shall be tested to meet the requirements prescribed.
SCOPE
1.1 This specification primarily covers greige tapes and webbings woven from “E” electrical classification glass fiber yarns. This specification can also be applied to tapes and webbings made of other glass fiber grades upon agreement between the purchaser and the supplier.
1.2 This specification is intended to assist ultimate users by designating the types of these products that are typical in the industry. This specification permits the application of organic materials to the glass fiber yarn during manufacture that helps facilitate weaving. When used as permitted in this specification, such materials will not interfere with the intended end use requirements.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D580/D580M −10
StandardSpecification for
1
Greige Woven Glass Tapes and Webbings
This standard is issued under the fixed designation D580/D580M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D1423Test Method for Twist in Yarns by Direct-Counting
D1776Practice for Conditioning and Testing Textiles
1.1 This specification primarily covers greige tapes and
D1777Test Method for Thickness of Textile Materials
webbings woven from “E” electrical classification glass fiber
D3773Test Methods for Length of Woven Fabric
yarns. This specification can also be applied to tapes and
D3774Test Method for Width of Textile Fabric
webbings made of other glass fiber grades upon agreement
D3775TestMethodforWarp(End)andFilling(Pick)Count
between the purchaser and the supplier.
of Woven Fabrics
1.2 This specification is intended to assist ultimate users by
D4963Test Method for Ignition Loss of Glass Strands and
designating the types of these products that are typical in the
Fabrics
industry. This specification permits the application of organic
D5035Test Method for Breaking Force and Elongation of
materials to the glass fiber yarn during manufacture that helps
Textile Fabrics (Strip Method)
facilitate weaving. When used as permitted in this
D7018TerminologyRelatingtoGlassFiberandItsProducts
specification, such materials will not interfere with the in- 4
2.2 ANSI Standard:
tended end use requirements.
ANSI/ASQC Z1.4Sampling Procedures for Inspection by
1.3 The values stated in either SI units or inch-pound units Attributes
are to be regarded separately as standard. The values stated in
3. Terminology
each system may not be exact equivalents; therefore, each
3.1 Definitions of Terms Specific to This Standard:
system shall be used independently of the other. Combining
3.1.1 Fordefinitionsofglassfiberandproducttermsusedin
values from the two systems may result in nonconformance
this specification refer to Terminology D7018.
with the standard.
3.1.2 The following terms are relevant to this standard:
1.4 This standard does not purport to address all of the
continuous filament yarn, greige goods, tape, webbing.
safety concerns, if any, associated with its use. It is the
3.1.3 Fordefinitionsofothertextileterminologyusedinthis
responsibility of the user of this standard to establish appro-
specification, refer to Terminology D123.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use.
4. Classification
4.1 Greige glass fiber tapes and webbings are produced in
2. Referenced Documents
twotypesandareconstructedwithyarnsdesignatedasdirected
2
2.1 ASTM Standards:
in Specification D578. The standard types are:
D123Terminology Relating to Textiles
4.1.1 Type A—Medium texture.
D578Specification for Glass Fiber Strands
4.1.2 Type B—Open texture.
D579Specification for Greige Woven Glass Fabrics
4.2 The designation of a tape or webbing shall be by style
D1059Test Method for Yarn Number Based on Short-
3
numbers that are standard throughout the industry.
Length Specimens (Withdrawn 2010)
4.3 Two segments of characters are used to describe tapes
1 and webbings.
This specification is under the jurisdiction of ASTM Committee D13 on
TextilesandisthedirectresponsibilityofSubcommitteeD13.18onGlassFiberand 4.3.1 Thefirstsegmentofthedescriptionoftapeorwebbing
its Products.
describestheglassclassification,thetypefiberinthewarp,and
CurrenteditionapprovedJune1,2010.PublishedJuly2010.Originallyapproved
the type fiber in the filling.
in1940.Lastpreviouseditionapprovedin2004asD580–04.DOI:10.1520/D0580
4.3.1.1 The first letter in the first segment is one of the
_D0580M-10.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
following glass classification codes: “E” for electrical,“ C” for
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
chemical, “S” for high strength.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
4
The last approved version of this historical standard is referenced on Available from American National Standards Institute, 11 W. 42nd St., 13th
www.astm.org. Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D580/D580M−10
4.3.1.2 The second letter in the first segment specifies the 8. Yarn Number
fiber type in the warp direction: “C” describes continuous
8.1 For tapes and webbings, the nominal size-free yarn
filament fiber using either SI units or inch-pound
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D580–04 Designation: D580/D580M – 10
Standard Specification for
1
Greige Woven Glass Tapes and Webbings
This standard is issued under the fixed designation D580/D580M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification primarily covers greige tapes and webbings woven from “E” electrical classification glass fiber yarns.
This specification can also be applied to tapes and webbings made of other glass fiber grades upon agreement between the
purchaser and the supplier.
1.2 This specification is intended to assist ultimate users by designating the types of these products that are typical in the
industry. This specification permits the application of organic materials to the glass fiber yarn during manufacture that helps
facilitate weaving. When used as permitted in this specification, such materials will not interfere with the intended end use
requirements.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in nonconformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
D123 Terminology Relating to Textiles
D578 Specification for Glass Fiber Strands
D579 Specification for Greige Woven Glass Fabrics
D1059 Test Method for Yarn Number Based on Short-Length Specimens
D1423 Test Method for Twist in Yarns by Direct-Counting
D1776 Practice for Conditioning and Testing Textiles
D1777 Test Method for Thickness of Textile Materials
D3773 Test Methods for Length of Woven Fabric
D3774 Test Method for Width of Textile Fabric
D3775 Test Method for Warp (End) and Filling (Pick) Count of Woven Fabrics
D3776Test Methods for Mass Per Unit Area (Weight) of Fabric
D4029Specification for Finished Woven Glass Fabrics
D4963 Test Method for Ignition Loss of Glass Strands and Fabrics
D5035 Test Method for Breaking Force and Elongation of Textile Fabrics (Strip Method)
D7018 Terminology Relating to Glass Fiber and Its Products
3
2.2 ANSI Standard:ANSI/ASQC Z1.4Sampling Procedures for Inspection by Attributes
3
ANSI/ASQC Z1.9Sampling Procedures and Tables for Inspection Variables for Percent Nonconforming ANSI/ASQC
Z1.4 Sampling Procedures for Inspection by Attributes
3. Terminology
3.1
1
ThisspecificationisunderthejurisdictionofASTMCommitteeD13onTextilesandisthedirectresponsibilityofSubcommitteeD13.18onGlassFiberandItsProducts.
Current edition approved Dec. 1, 2004. Published January 2005. Originally approved in 1940. Last previous edition approved in 1999 as D580–99.on Glass Fiber and its
Products.
Current edition approved June 1, 2010. Published July 2010. Originally approved in 1940. Last previous edition approved in 2004 as D580–04. DOI:
10.1520/D0580_D0580M-10.
2
ForreferencedASTMstandards,visittheASTMwebsite,www.astm.org,orcontactASTMCustomerServiceatservice@astm.org.For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website. DOI: 10.1520/D0580-04.
3
Available from American National Standards Institute, 11 W. 42nd St., 13th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
D580/D580M – 10
3.1 Definitions of Terms Specific to This Standard:
3.1.1 For definitions of glass fiber and product terms used in this specification refer to Terminology D7018.
3.1.2For definitions of other textile terminology used in this specification, refer to Terminology
3.1.2 The following terms are relevant to this standard: continuous filament yarn, greige goods, tape, webbing.
3.1.3 For definitions of other textile terminology used in this specification, refer to Terminology D123.
4. Classification
4.1 Greige glass fiber tapes and webbings are produced in two types and are constructed with yarns designated as directed in
Spe
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.