ASTM B710-04

Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe

ABSTRACT
This specification covers UNS N08330 and N08332 high-temperature alloy welded pipes for heat-resisting applications and general corrosive service. The pipes should be made from the flat-rolled alloys by an automatic welding process without any filler metal additions. After welding, the materials should be cold worked, either in weld and base metal or in weld metal only, then annealed. Each end of one pipe per lot will be subjected to a flattening test.
SCOPE
1.1 This specification covers alloys UNS N08330 and UNS N08332 in the form of welded pipe intended for heat-resisting applications and general-corrosive service.
1.2 The pipe covered is nominal pipe sizes up to and including size 12, with the nominal wall thicknesses given as Schedules 5S, 10S, 40S, and 80S. of Specification B 775 is based on Table A1 of ANSI B36.19 and gives the nominal dimension of these sizes. Table 3 of Specification B 775 lists the dimensional requirements of these sizes. Pipe having other dimensions may be furnished provided such pipe complies with all other requirements of this specification.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-Jan-2004
• Technical Committee: B02 - Nonferrous Metals and Alloys
• Drafting Committee: B02.07 - Refined Nickel and Cobalt and Their Alloys

Relations

• Replaces: ASTM B710-99 - Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe
• Effective Date: 01-Feb-2004
• Replaced By: ASTM B710-04(2009) - Standard Specification for Nickel-Iron-Chromium-Silicon Alloy Welded Pipe
• Effective Date: 01-Oct-2009
• Referred By: ASTM B366/B366M-23 - Standard Specification for Factory-Made Wrought Nickel and Nickel Alloy Fittings
• Effective Date: 01-Feb-2004

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: B 710 – 04
Standard Specification for
1
Nickel-Iron-Chromium-Silicon Alloy Welded Pipe
This standard is issued under the fixed designation B 710; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
TABLE 1 Chemical Requirements
1. Scope
2
Element Composition Limits, %
1.1 Thisspecification coversalloysUNSN08330andUNS
A
C .
N08332 in the form of welded pipe intended for heat-resisting
Mn 2.00 max
applications and general-corrosive service.
P 0.03 max
1.2 The pipe covered is nominal pipe sizes up to and
S 0.03 max
Si 0.75–1.50
including size 12, with the nominal wall thicknesses given as
Cr 17.0–20.0
Schedules 5S, 10S, 40S, and 80S. Table 2 of Specification
Ni 34.0–37.0
B 775 is based on Table A1 of ANSI B36.19 and gives the
Cu 1.00 max
Pb 0.005 max
nominal dimension of these sizes. Table 3 of Specification
Sn 0.025 max
B 775 lists the dimensional requirements of these sizes. Pipe
B
Fe remainder
having other dimensions may be furnished provided such pipe
A
Alloy UNS N08330: 0.08 max. Alloy UNS N08332: 0.05–0.10.
complies with all other requirements of this specification. B
lement shall be determined arithmetically by difference.
1.3 The values stated in inch-pound units are to be regarded
as the standard. The values given in parentheses are for
4
2.2 ANSI Standard:
information only.
ANSI B36.19 Stainless Steel Pipe
1.4 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
3. Terminology
responsibility of the user of this standard to become familiar
3.1 Definitions:
with all hazards including those identified in the appropriate
3.1.1 Definitions for terms defined in Terminology B 899
Material Safety Data Sheet for this product/material as pro-
shallapplyunlessotherwisedefinedbytherequirementsofthis
vided by the manufacturer, to establish appropriate safety and
document.
health practices, and determine the applicability of regulatory
limitations prior to use.
4. General Requirement
4.1 Material furnished in accordance with this specification
2. Referenced Documents
3 shall conform to the applicable requirements of the current
2.1 ASTM Standards:
edition of Specification B 775 unless otherwise provided
B 536 Specification for Nickel-Iron-Chromium-Silicon Al-
herein.
loy (UNS N08330 and N08332) Plate, Sheet, and Strip
B 775 Specification for General Requirements for Nickel
5. Ordering Information
and Nickel Alloy Welded Pipe
5.1 It is the responsibility of the purchaser to specify all
B 899 Terminology Relating to Non-ferrous Metals and
requirements that are necessary for material ordered under this
Alloys
specification. Examples of such requirements include, but are
not limited to, the following:
1
This specification is under the jurisdiction of ASTM Committee B02 on
5.1.1 Quantity (feet or number of lengths),
Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee
5.1.2 UNS number,
B02.07 on Refined Nickel and Cobalt and Their Alloys.
5.1.3 Size (nominal pipe size and schedule),
Current edition approved Feb. 1, 2004. Published February 2004. Originally
approved in 1982. Last previous edition approved in 1999 as B 710 – 99. 5.1.4 Length (random or specific),
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
5.1.5 ASTM designation,
cation SB710 in Section 11 of that code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute, 11 West 42nd St., 13th
the ASTM website. Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B710–04
TABLE 2 Mechanical Properties
Tensile Strength, min, Yield Strength, 0.2 % Elongation in 2 in. or
A
Alloy Condition Hardness
psi (MPa) offset, min, psi (MPa) 50 mm, or 4D, min,%
UNS N08330 annealed 70 000 (483) 30 000 (207) 30 70 to 90 HRB
UNS N08332 annealed 67 000 (462) 27 000 (186) 30 65 to 88 HRB
A
Hardness values are informative only and not to be construed as the basis for acceptance.
5.1.6 Product Analysis— State if required. 8. Mechanical Properties and Other Requirements
5.1.7 Certification— State if a certification or report of test
8.1 Mechanical Properties—The material shall conform to
results is required,
themechanicalpropertyrequirementsspecifiedinTable2.One
5.1.8 Purchaser Inspection—State which tes
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:B 710–99 Designation: B 710 – 04
Standard Specification for
1
Nickel-Iron-Chromium-Silicon Alloy Welded Pipe
This standard is issued under the fixed designation B 710; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
2
1.1 This specification covers alloys UNS N08330 and UNS N08332 in the form of welded pipe intended for heat-resisting
applications and general-corrosive service.
1.2 The pipe covered is nominal pipe sizes up to and including size 12, with the nominal wall thicknesses given as Schedules
5S, 10S, 40S, and 80S. Table 2 of Specification B 775B 775 is based on Table B 536 of ANSI B36.19 B 775 is based on Table
A1 of ANSI B36.19 and gives the nominal dimension of these sizes. Table 3 of Specification B 775B 775 lists the dimensional
requirements of these sizes. Pipe having other dimensions may be furnished provided such pipe complies with all other
requirements of this specification.
1.3 The values stated in inch-pound units are to be regarded as the standard.The values given in parentheses are for information
only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data
Sheet for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine
the applicability of regulatory limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
B 536 Specification for Nickel-Iron-Chromium-Silicon Alloy (UNS N08330 and N08332) Plate, Sheet, and Strip
3
B 775 Specification for General Requirements for Nickel and Nickel Alloy Welded Pipe Specification for General
Requirements for Nickel and Nickel Alloy Welded Pipe
B 899 Terminology Relating to Non-ferrous Metals and Alloys
4
2.2 ANSI Standard:
ANSI B36.19 Stainless Steel Pipe
3. Terminology
3.1 Definitions:
3.1.1 Definitions for terms defined inTerminology B 899B 899 shall apply unless otherwise defined by the requirements of this
document.
4. General Requirement
34.1 Material furnished in accordance with this specification shall conform to the applicable requirements of the current edition
of Specification B 775B 775 unless otherwise provided herein.
4.
5. Ordering Information
4.1It5.1 It is the responsibility of the purchaser to specify all requirements that are necessary for the safe and satisfactory
performance of material ordered under this specification. Examples of such requirements include, but are not limited to, the
following:
1
This specification is under the jurisdiction of ASTM Committee B-2 B02 on Nonferrous Metals and Alloys and is the direct responsibility of Subcommittee B02.07 on
Refined Nickel and Cobalt and Their Alloys.
Current edition approved May 10, 1999. Published June 1999. Originally published as B 710–82. Last previous edition B 710–94.
Current edition approved Feb. 1, 2004. Published February 2004. Originally approved in 1982. Last previous edition approved in 1999 as B 710 – 99.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specification SB710 in Section 11 of that code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
, Vol 02.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American National Standards Institute, 11 West 42nd St., 13th Floor, New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
B710–04
TABLE 1 Chemical Requirements
Element Composition Limits, %
A
C .
Mn 2.00 max
P 0.03 max
S 0.03 max
Si 0.75–1.50
Cr 17.0–20.0
Ni 34.0–37.0
Cu 1.00 max
Pb 0.005 max
Sn 0.025 max
B
Fe remainder
A
Alloy UNS N08330: 0.08 max. Alloy UNS N08332: 0.05–0.10.
B
lement shall be determined arithmetically by difference.
TABLE 2 Mechanical Properties
Tensile Strength, min, Yield Strength, 0.2 % Elongation in 2 in. or
A
Alloy Condition Hardness
psi (MPa) offset, min, psi (MPa) 50 mm, or 4D, min,%
UNS N08330 annealed 70 000 (483) 30 000 (207) 30 70 to 90 HRB
UNS N0
...