ASTM A479/A479M-05

Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels

SCOPE
1.1 This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04.
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards; within the text and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each system must be used independent of the other. Combining values from the two systems may result in nonconformance with the specification.
1.3 Unless the order specifies the applicable "M" specification designation, the material shall be furnished to the inch-pound units.

General Information

• Status: Historical
• Publication Date: 28-Feb-2005
• ICS: 77.140.30 - Steels for pressure purposes
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.17 - Flat-Rolled and Wrought Stainless Steel

Relations

• Replaces: ASTM A479/A479M-04 - Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
• Effective Date: 01-Mar-2005
• Replaced By: ASTM A479/A479M-05a - Standard Specification for Stainless Steel Bars and Shapes for Use in Boilers and Other Pressure Vessels
• Effective Date: 01-Sep-2005
• Referred By: ASTM A1082/A1082M-16(2021) - Standard Specification for High Strength Precipitation Hardening and Duplex Stainless Steel Bolting for Special Purpose Applications
• Effective Date: 01-Mar-2005
• Referred By: ASTM F3184-16 - Standard Specification for Additive Manufacturing Stainless Steel Alloy (UNS S31603) with Powder Bed Fusion
• Effective Date: 01-Mar-2005
• Referred By: ASTM C1533-15(2022) - Standard Guide for General Design Considerations for Hot Cell Equipment
• Effective Date: 01-Mar-2005
• Referred By: ASTM A484/A484M-23 - Standard Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
• Effective Date: 01-Mar-2005
• Referred By: ASTM A1069/A1069M-19 - Standard Specification for Laser and Laser Hybrid Welded Stainless Steel Bars, Plates, and Shapes
• Effective Date: 01-Mar-2005
• Referred By: ASTM A580/A580M-23 - Standard Specification for Stainless Steel Wire
• Effective Date: 01-Mar-2005
• Referred By: ASTM B649-21 - Standard Specification for Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy and Cr-Ni-Fe-N <brk/>Low-Carbon Alloy Bar and Wire, Ni-Cr-Fe-Mo-N Alloy Wire, and Ni-Fe-Cr-Mo-N Alloy Bar
• Effective Date: 01-Mar-2005
• Referred By: ASTM F1376-92(2020) - Standard Guide for Metallurgical Analysis for Gas Distribution System Components (Withdrawn 2023)
• Effective Date: 01-Mar-2005
• Referred By: ASTM F1508-96(2021) - Standard Specification for Angle Style, Pressure Relief Valves for Steam, Gas, and Liquid Services
• Effective Date: 01-Mar-2005
• Referred By: ASTM F1387-23 - Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings
• Effective Date: 01-Mar-2005
• Referred By: ASTM A182/A182M-23 - Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service
• Effective Date: 01-Mar-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Used in USDOE-NE Standards
Designation: A 479/A 479M – 05
Standard Specification for
Stainless Steel Bars and Shapes for Use in Boilers and
1
Other Pressure Vessels
This standard is issued under the fixed designationA 479/A 479M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope* E112 Test Methods for Determining Average Grain Size
2 E 527 Practice for Numbering Metals and Alloys (UNS)
1.1 This specification covers hot- and cold-finished bars of
2.2 Other Document:
stainless steel, including rounds, squares, and hexagons, and
SAE J 1086 Recommended Practice for Numbering Metals
hot-rolledorextrudedshapessuchasangles,tees,andchannels
4
2
and Alloys
for use in boiler and pressure vessel construction.
NOTE 1—There are standards covering high nickel, chromium, austen- 3. Ordering Information
itic corrosion, and heat-resisting alloy materials. These standards are
3.1 It is the responsibility of the purchaser to specify all
under the jurisdiction ofASTM Subcommittee B02.07 and may be found
requirements that are necessary for material ordered under this
in Annual Book of ASTM Standards, Vol 02.04.
specification. Such requirements may include, but are not
1.2 The values stated in either inch-pound units or SI
limited to, the following:
(metric)unitsaretoberegardedseparatelyasstandards;within
3.1.1 Quantity (weight or number of pieces);
the text and tables, the SI units are shown in [brackets]. The
3.1.2 Dimensions, including diameter or thickness (and
values stated in each system are not exact equivalents; there-
width), shape or form, applicable prints or sketches, length,
fore, each system must be used independent of the other.
etc.;
Combining values from the two systems may result in noncon-
3.1.3 Type or UNS designation (Table 1);
formance with the specification.
3.1.4 ASTM designation and edition year if other than latest
1.3 Unless the order specifies the applicable “M” specifica-
edition;
tion designation, the material shall be furnished to the inch-
3.1.5 Heat treated condition (Section 4);
pound units.
3.1.6 Finish (see Manufacture section of Specification
A 484/A 484M);
2. Referenced Documents
3.1.7 Supplementary Requirements invoked for special ser-
3
2.1 ASTM Standards:
vices (described at the end of this specification);
A 262 Practices for Detecting Susceptibility to Intergranu-
3.1.8 Whether bars are to be rolled as bars or cut from strip
lar Attack in Austenitic Stainless Steels
or plate;
A 370 Test Methods and Definitions for MechanicalTesting
3.1.9 Preparation for delivery (see Preparation for Delivery
of Steel Products
section of Specification A 484/A 484M);
A 484/A 484M Specification for General Requirements for
3.1.10 Marking requirements (see Marking section of
Stainless Steel Bars, Billets, and Forgings
Specification A 484/A 484M);
A 751 Test Methods, Practices, and Terminology for
3.1.11 Surface preparation of shapes (see Manufacture sec-
Chemical Analysis of Steel Products
tion of Specification A 484/A 484M); and
3.1.12 The intended use of the material, if the purchaser
1 considers this useful information.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
NOTE 2—A typical ordering description is as follows: 5000 lb [2000
A01.17 on Flat-Rolled and Wrought Stainless Steel.
kg]; 1.000 in. [25 mm] round bar by 10 to 12 ft [3 to 4 m]; Type 304 or
Current edition approved March 1, 2005. Published March 2005. Originally
UNS S30400; to Specification A 479 [A 479M]; annealed; centerless
approved in 1962. Last previous edition approved in 2004 as A 479/A 479M – 04.
2
ground; plus any optional supplementary requirements, such as, for
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
cation SA-479/SA-479M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 479/A 479M – 05
example, special marking instructions.
4.1.4 High tensile
...

This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE Standards
Designation:A 479/A 479M–04 Designation: A 479/A 479M – 05
Standard Specification for
Stainless Steel Bars and Shapes for Use in Boilers and
1
Other Pressure Vessels
This standard is issued under the fixed designationA 479/A 479M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers hot- and cold-finished bars of stainless steel, including rounds, squares, and hexagons, and
2
hot-rolled or extruded shapes such as angles, tees, and channels for use in boiler and pressure vessel construction.
NOTE 1—There are standards covering high nickel, chromium, austenitic corrosion, and heat-resisting alloy materials. These standards are under the
jurisdiction of ASTM Subcommittee B02.07 and may be found in Annual Book of ASTM Standards, Vol 02.04.
1.2 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standards; within the text
and tables, the SI units are shown in [brackets]. The values stated in each system are not exact equivalents; therefore, each system
must be used independent of the other. Combining values from the two systems may result in nonconformance with the
specification.
1.3 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound
units.
2. Referenced Documents
3
2.1 ASTM Standards:
A 262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A 370 Test Methods and Definitions for Mechanical Testing of Steel Products
A 484/A 484M Specification for General Requirements for Stainless Steel Bars, Billets, and Forgings
A 751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
E112 Test Methods for Determining Average Grain Size
E 527 Practice for Numbering Metals and Alloys (UNS)
2.2 Other Document:
4
SAE J 1086 Recommended Practice for Numbering Metals and Alloys
3. Ordering Information
3.1 It is the responsibility of the purchaser to specify all requirements that are necessary for material ordered under this
specification. Such requirements may include, but are not limited to, the following:
3.1.1 Quantity (weight or number of pieces);
3.1.2 Dimensions, including diameter or thickness (and width), shape or form, applicable prints or sketches, length, etc.;
3.1.3 Type or UNS designation (Table 1);
3.1.4 ASTM designation and edition year if other than latest edition;
3.1.5 Heat treated condition (Section 4);
3.1.6 Finish (see Manufacture section of Specification A 484A 484/A 484M/A 484M);
3.1.7 Supplementary Requirements invoked for special services (described at the end of this specification);
3.1.8 Whether bars are to be rolled as bars or cut from strip or plate;
3.1.9 Preparation for delivery (see Preparation for Delivery section of Specification A 484A 484/A 484M/A 484M);
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Feb.March 1, 2004.2005. Published February 2004.March 2005. Originally approved in 1962. Last previous edition approved in 20032004 as
A 479/A 479M – 034.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-479/SA-479M in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at [e-mail]. For Annual Book ofASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
A 479/A 479M – 05
3.1.10 Marking requirements (see Marking section of Specification A 484A 484/A 484M/A 484M);
3.1.11 Surface preparation of shapes (see Manufacture section of Specification A 484A 484/A 484M/A 484M); and
3.1.12 The intended use of the material, if t
...