Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

SCOPE
1.1 This specification covers solvent cement for joining acrylonitrile-butadiene styrene (ABS) plastic pipe and fittings for pressure and nonpressure systems.  
1.2 Recommendation for using solvent cement for joining acrylonitrile-butadiene-styrene (ABS) plastic pipe and fittings is given in Appendix X1. Satisfactory joining of pipe and fittings cannot be made in the presence of water, as water destroys the bonding ability of solvent cement; therefore, all materials must be dry for satisfactory joining.  
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-Oct-2021
Technical Committee
Drafting Committee
Current Stage
Ref Project

Buy Standard

Technical specification
ASTM D2235-21 - Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D2235-21 - Standard Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings
English language
6 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2235 −21 An American National Standard
Standard Specification for
Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS)
1
Plastic Pipe and Fittings
This standard is issued under the fixed designation D2235; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers solvent cement for joining
D329 Specification for Acetone
acrylonitrile-butadiene styrene (ABS) plastic pipe and fittings
D618 Practice for Conditioning Plastics for Testing
for pressure and nonpressure systems.
D740 Specification for Methyl Ethyl Ketone
1.2 Recommendation for using solvent cement for joining
D883 Terminology Relating to Plastics
acrylonitrile-butadiene-styrene (ABS) plastic pipe and fittings
D1084 Test Methods for Viscosity of Adhesives
is given in Appendix X1. Satisfactory joining of pipe and
D1527 Specification for Acrylonitrile-Butadiene-Styrene
fittings cannot be made in the presence of water, as water
(ABS) Plastic Pipe, Schedules 40 and 80 (Withdrawn
3
destroys the bonding ability of solvent cement; therefore, all
2013)
materials must be dry for satisfactory joining.
D2282 Specification for Acrylonitrile-Butadiene-Styrene
3
(ABS) Plastic Pipe (Withdrawn 2006)
1.3 The text of this specification references notes, footnotes,
D2465 Specification for Threaded Acrylonitrile-Butadiene-
and appendixes which provide explanatory material. These
Styrene (ABS) Plastic Pipe Fittings, Schedule 80 (With-
notesandfootnotes(excludingthoseintablesandfigures)shall
3
drawn 1985)
not be considered as requirements of the specification.
D2468 Specification for Acrylonitrile-Butadiene-Styrene
1.4 The values stated in inch-pound units are to be regarded
(ABS) Plastic Pipe Fittings, Schedule 40 (Withdrawn
3
as standard. The values given in parentheses are mathematical
2003)
conversions to SI units that are provided for information only
D2469 Specification for Socket-Type Acrylonitrile-
and are not considered standard.
Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule
3
80 (Withdrawn 1985)
1.5 The following safety hazards caveat pertains only to the
D2661 Specification for Acrylonitrile-Butadiene-Styrene
test methods portion, Section 7, of this specification: This
(ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe
standarddoesnotpurporttoaddressallofthesafetyconcerns,
and Fittings
ifany,associatedwithitsuse.Itistheresponsibilityoftheuser
D2680 Specification for Acrylonitrile-Butadiene-Styrene
of this standard to establish appropriate safety, health, and
(ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer
environmental practices and determine the applicability of
Piping
regulatory limitations prior to use.
D2750 Specification for Acrylonitrile-Butadiene-Styrene
1.6 This international standard was developed in accor-
(ABS) Plastics Utilities Conduit and Fittings (Withdrawn
dance with internationally recognized principles on standard-
3
1997)
ization established in the Decision on Principles for the
D2751 Specification for Acrylonitrile-Butadiene-Styrene
Development of International Standards, Guides and Recom-
3
(ABS) Sewer Pipe and Fittings (Withdrawn 2014)
mendations issued by the World Trade Organization Technical
D1600 Terminology forAbbreviatedTerms Relating to Plas-
Barriers to Trade (TBT) Committee.
tics
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
1
This specification is under the jurisdiction ofASTM Committee F17 on Plastic contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Nov. 1, 2021. Published November 2021. Originally the ASTM website.
3
approved in 1963. Last previous edition approved 2016 as D2235 – 04(2016). DOI: The last approved version of this historical standard is referenced on
10.1520/D2235-21. www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2235−21
D3965 ClassificationSystemandBasisforSpecificationsfor 5.2 Acrylonitrile-Butadiene-Styrene (ABS) Plastic—
Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials Plastic containing polymers in which the minimum butadiene
for Pipe and Fittings content is 6 %, the minimum acrylonitrile content is 15 %, the
F402 Practice for Safe Handling of Solvent Cements, mini
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2235 − 04 (Reapproved 2016) D2235 − 21 An American National Standard
Standard Specification for
Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS)
1
Plastic Pipe and Fittings
This standard is issued under the fixed designation D2235; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers solvent cement for joining acrylonitrile-butadiene styrene (ABS) plastic pipe and fittings for pressure
and nonpressure systems.
1.2 Recommendation for using solvent cement for joining acrylonitrile-butadiene-styrene (ABS) plastic pipe and fittings is given
in Appendix X1. Satisfactory joining of pipe and fittings cannot be made in the presence of water, as water destroys the bonding
ability of solvent cement; therefore, all materials must be dry for satisfactory joining.
1.3 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and
footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D329 Specification for Acetone
D618 Practice for Conditioning Plastics for Testing
D740 Specification for Methyl Ethyl Ketone
D883 Terminology Relating to Plastics
D1084 Test Methods for Viscosity of Adhesives
3
D1527 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe, Schedules 40 and 80 (Withdrawn 2013)
1
This specification is under the jurisdiction of ASTM Committee F17 on Plastic Piping Systems and is the direct responsibility of Subcommittee F17.20 on Joining.
Current edition approved Nov. 1, 2016Nov. 1, 2021. Published November 2016November 2021. Originally approved in 1963. Last previous edition approved 20112016
as D2235 – 04(2011).(2016). DOI: 10.1520/D2235-04R16.10.1520/D2235-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2235 − 21
3
D2282 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Withdrawn 2006)
3
D2465 Specification for Threaded Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 80 (Withdrawn 1985)
3
D2468 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 40 (Withdrawn 2003)
D2469 Specification for Socket-Type Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe Fittings, Schedule 80 (Withdrawn
3
1985)
D2661 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings
D2680 Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping
3
D2750 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastics Utilities Conduit and Fittings (Withdrawn 1997)
3
D2751 Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014)
D1600 Term
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.