ASTM F2376-13
(Practice)Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems
Standard Practice for Classification, Design, Manufacture, Construction, and Operation of Water Slide Systems
SCOPE
1.1 This practice applies to the classification, design, manufacture, construction, and operation of water slide systems. Water slide systems shall be defined as rides intended for use by riders in bathing attire where the action of the ride involves possible and purposeful immersion of the rider's body either in whole or in part in water, and uses circulating water to mobilize or lubricate the rider’s transportation along a purpose built path. This includes slides used with or without vehicles as defined below. The terms water slides, waterslides, and slides shall be considered equivalent when used in this practice.
1.2 For the purposes of this practice, a water slide system includes:
1.2.1 The flume,
1.2.2 The water-circulation system,
1.2.3 The starting platform with associated means of access and egress,
1.2.4 The structural supports,
1.2.5 Vehicles or other aquatic accessories that are part of the water slide as defined by the manufacturer, and
1.2.6 Means of slide termination.
1.3 This practice shall not apply to:
1.3.1 Any water slides installed in private residences,
1.3.2 Water flume amusement rides where contact with water is merely incidental (for example, log flume rides, shoot-the-chutes),
1.3.3 Amusement rides and devices whose design criteria are specifically addressed in another ASTM standard,
1.3.4 Lazy river type attractions operating at constant elevation, constructed in the ground, and
1.4 Pre-existing designs manufactured after the effective date of publication of this practice if the design is service proven or previously compliant, as defined in Section 3.1.26 of Practice F2291, and the manufacturer provides:
1.4.1 A historical summary of the water slide, or major modification as defined in Terminology F747, and
1.4.2 A statement that the design is service proven or previously compliant. Water slides and major modifications to water slides may qualify as previously compliant for five years following the date of publication of this practice. Thereafter, water slides and major modifications to water slides must qualify as service proven or meet the requirements of this practice.
1.4.3 Service proven or previously compliant designs shall comply with Section 8.
1.5 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.Note 1—The conversion factor from inch-pound to metric units is 1 in. = 25.4 mm, and 1 lb = 4.4482 N.
1.6 This practice includes an Appendix, which provides additional information to enhance the user's understanding of and application of the criteria presented in this practice, for example, rationale, background, drawings, interpretation, or commentary. The information in the Appendix shall not be considered a mandatory part of this practice.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2376 −13
Standard Practice for
Classification, Design, Manufacture, Construction, and
1
Operation of Water Slide Systems
This standard is issued under the fixed designation F2376; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 1.4.1 A historical summary of the water slide, or major
modification as defined in Terminology F747, and
1.1 This practice applies to the classification, design,
1.4.2 A statement that the design is service proven or
manufacture, construction, and operation of water slide sys-
previously compliant. Water slides and major modifications to
tems.Water slide systems shall be defined as rides intended for
water slides may qualify as previously compliant for five years
use by riders in bathing attire where the action of the ride
following the date of publication of this practice. Thereafter,
involvespossibleandpurposefulimmersionoftherider’sbody
water slides and major modifications to water slides must
either in whole or in part in water, and uses circulating water to
qualify as service proven or meet the requirements of this
mobilize or lubricate the rider’s transportation along a purpose
practice.
built path.This includes slides used with or without vehicles as
1.4.3 Service proven or previously compliant designs shall
defined below. The terms water slides, waterslides, and slides
comply with Section 8.
shall be considered equivalent when used in this practice.
1.5 The values stated in inch-pound units are to be regarded
1.2 For the purposes of this practice, a water slide system
as standard. No other units of measurement are included in this
includes:
standard.
1.2.1 The flume,
NOTE 1—The conversion factor from inch-pound to metric units is 1
1.2.2 The water-circulation system,
in. = 25.4 mm, and 1 lb = 4.4482 N.
1.2.3 The starting platform with associated means of access
1.6 This practice includes an Appendix, which provides
and egress,
additional information to enhance the user’s understanding of
1.2.4 The structural supports,
and application of the criteria presented in this practice, for
1.2.5 Vehicles or other aquatic accessories that are part of
example, rationale, background, drawings, interpretation, or
the water slide as defined by the manufacturer, and
commentary. The information in the Appendix shall not be
1.2.6 Means of slide termination.
considered a mandatory part of this practice.
1.3 This practice shall not apply to:
1.7 This standard does not purport to address all of the
1.3.1 Any water slides installed in private residences,
safety concerns, if any, associated with its use. It is the
1.3.2 Water flume amusement rides where contact with
responsibility of the user of this standard to establish appro-
water is merely incidental (for example, log flume rides,
priate safety and health practices and determine the applica-
shoot-the-chutes),
bility of regulatory limitations prior to use.
1.3.3 Amusement rides and devices whose design criteria
are specifically addressed in another ASTM standard,
2. Referenced Documents
1.3.4 Lazy river type attractions operating at constant
2
2.1 ASTM Standards:
elevation, constructed in the ground, and
D570 Test Method for Water Absorption of Plastics
1.4 Pre-existing designs manufactured after the effective
D638 Test Method for Tensile Properties of Plastics
date of publication of this practice if the design is service
D790 Test Methods for Flexural Properties of Unreinforced
proven or previously compliant, as defined in Section 3.1.26 of
and Reinforced Plastics and Electrical Insulating Materi-
Practice F2291, and the manufacturer provides:
als
F747 Terminology Relating to Amusement Rides and De-
vices
1
This practice is under the jurisdiction ofASTM Committee F24 on Amusement
RidesandDevicesandisthedirectresponsibilityofSubcommitteeF24.70onWater
2
Related Amusement Rides and Devices. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved June 1, 2013. Published May 2014. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2006. Last previous edition approved in 2008 as F2376 – 08. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/F2376-13. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2376−13
F770 Practice for Ownership, Operation, Maintenance, and 4.1.4 serpentine slide—curved path as viewed in geometric
Inspection of Amusement Rides and Devices s
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2376 − 08 F2376 − 13
Standard Practice for
Classification, Design, Manufacture, Construction, and
1
Operation of Water Slide Systems
This standard is issued under the fixed designation F2376; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice applies to the classification, design, manufacture, construction, and operation of water slide systems. Water
slide systems shall be defined as rides intended for use by riders in bathing attire where the action of the ride involves possible
and purposeful immersion of the rider’s body either in whole or in part in water, and uses circulating water to mobilize or lubricate
the rider’s transportation along a purpose built path. This includes slides used with or without vehicles as defined below. The terms
water slides, waterslides, and slides shall be considered equivalent when used in this practice.
1.2 For the purposes of this practice, a water slide system includes:
1.2.1 The flume,
1.2.2 The water-circulation system,
1.2.3 The starting platform with associated means of access and egress,
1.2.4 The structural supports,
1.2.5 Vehicles or other aquatic accessories that are part of the water slide as defined by the manufacturer, and
1.2.6 Means of slide termination.
1.3 This practice shall not apply to:
1.3.1 Any water slides installed in private residences,
1.3.2 Water flume amusement rides where contact with water is merely incidental (for example, log flume rides, shoot-the-
chutes),
1.3.3 Amusement rides and devices whose design criteria are specifically addressed in another ASTM standard,
1.3.4 Lazy river type attractions operating at constant elevation, constructed in the ground, and
1.4 Pre-existing designs manufactured after the effective date of publication of this practice if the design is service proven or
previously compliant, as defined in Section 3.1.26 of Practice F2291, and the manufacturer provides:
1.4.1 A historical summary of the water slide, or major modification as defined in Terminology F747, and
1.4.2 A statement that the design is service proven or previously compliant. Water slides and major modifications to water slides
may qualify as previously compliant for five years following the date of publication of this practice. Thereafter, water slides and
major modifications to water slides must qualify as service proven or meet the requirements of this practice.
1.4.3 Service proven or previously compliant designs shall comply with Section 8.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are for information
only.No other units of measurement are included in this standard.
NOTE 1—The conversion factor from inch-pound to metric units is 1 in. = 25.4 mm, and 1 lb = 4.4482 N.
1.6 This practice includes an Appendix, which provides additional information to enhance the user’s understanding of and
application of the criteria presented in this practice, for example, rationale, background, drawings, interpretation, or commentary.
The information in the Appendix shall not be considered a mandatory part of this practice.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1
This practice is under the jurisdiction of ASTM Committee F24 on Amusement Rides and Devices and is the direct responsibility of Subcommittee F24.70 on Water
Related Amusement Rides and Devices.
Current edition approved March 1, 2008June 1, 2013. Published April 2008May 2014. Originally approved in 2006. Last previous edition approved in 20072008 as
F2376 – 07.F2376 – 08. DOI: 10.1520/F2376-08.10.1520/F2376-13.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F2376 − 13
2. Referenced Documents
2
2.1 ASTM Standards:
D570 Test Method for Water Absorption of Plastics
D638 Test Method for Tensile Properties of Plastics
D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials
3
F698 Specification for Physical Informat
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.