ASTM F1072-94(2018)

Standard Specification for Expanded-Metal Doors

ABSTRACT
This specification covers steel expanded-metal doors suitable for installation in expanded-metal bulkheads, structural bulkheads, and structural arches. Expanded-metal doors are furnished in four types: Type I (right hand), Type II (left hand), Type III (right hand reverse) and Type IV (left hand reverse). Doors shall be furnished with the vertical support channels and top angle in place. A temporary brace shall be included at the frame bottom to prevent racking. Doors shall be fitted with rubber-tipped bumpers and a manually operated catch for holding doors in an open position. Provision shall be made for the installation of a rim latch set operated by knobs on both sides. Doors and frames shall be free from all cracks, burrs, sharp edges, and other defects.
SCOPE
1.1 This specification covers steel expanded-metal doors suitable for installation in expanded-metal bulkheads, structural bulkheads, and structural arches.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2018
• ICS: 47.020.10 - Hulls and their structure elements
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1072 − 94 (Reapproved 2018) An American National Standard
Standard Specification for
Expanded-Metal Doors
This standard is issued under the fixed designation F1072; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Classification
3.1 Expanded-metal doors are furnished in four types (see
1.1 This specification covers steel expanded-metal doors
Detail “J”) as follows:
suitable for installation in expanded-metal bulkheads, struc-
3.1.1 Type I—Right hand (RH).
tural bulkheads, and structural arches.
3.1.2 Type II—Left hand (LH).
1.2 The values stated in inch-pound units are to be regarded
3.1.3 Type III—Right hand reverse (RHR).
as standard. The values given in parentheses are mathematical
3.1.4 Type IV—Left hand reverse (LHR).
conversions to SI units that are provided for information only
and are not considered standard.
4. Ordering Information
1.3 This international standard was developed in accor-
4.1 Orders for doors under this specification shall include
dance with internationally recognized principles on standard-
this specification number and type.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
5. Materials and Manufacture
mendations issued by the World Trade Organization Technical
5.1 Materials—See Table 1.
Barriers to Trade (TBT) Committee.
5.2 Manufacture:
5.2.1 Doors shall be furnished with the vertical support
2. Referenced Documents
channels and top angle in place. A temporary brace shall be
2.1 ASTM Standards:
included at the frame bottom to prevent racking.
A36/A36M Specification for Carbon Structural Steel
5.2.2 Welding shall be in accordance with AWS D1.1
A167 Specification for Stainless and Heat-Resisting
Structural Welding Code or ABS Rules for Building and
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
Classing Steel Vessels.
drawn 2014)
D3951 Practice for Commercial Packaging
6. Installation Requirements
F783 Specification for Staple, Handgrab, Handle, and Stir-
6.1 Doors shall be fitted with rubber-tipped bumpers and a
rup Rung
manually operated catch for holding doors in an open position.
2.2 Other Documents:
These shall be furnished and installed by others.
ABS Rules for Building and Classing Steel Vessels
6.2 Provision shall be made for the installation of a rim latch
AWS D1.1 Structural Welding Code
set operated by knobs on both sides. This hardware shall be
furnished and installed by others.
6.3 Padlocks shall be furnished by others.
This specification is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
6.4 Any holes needed in the frame for installation in
Outfitting and Deck Machinery.
expanded-metal or other types of bulkheads shall be made at
Current edition approved April 1, 2018. Published May 2018. Originally
installation by others.
approved in 1987. Last previous edition approved in 2012 as F1072 – 94 (2012).
DOI: 10.1520/F1072-94R18.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
7. Dimensions and Tolerances
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
7.1 Dimensions are as indicated in Figs. 1-8 and Table 1.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
7.2 Tolerance—6 ⁄16 in. (1.5 mm).
The last approved version of this historical standard is referenced on
www.astm.org.
Available from American Bureau of Shipping (ABS), ABS Plaza, 16855 8. Workmanship, Finish, and Appearance
Northchase Dr., Houston, TX 77060, http://www.eagle.org.
5 8.1 Doors and frames shall be free from all cracks, burrs,
Availabl
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1072 − 94 (Reapproved 2012) F1072 − 94 (Reapproved 2018)An American National Standard
Standard Specification for
Expanded-Metal Doors
This standard is issued under the fixed designation F1072; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers steel expanded-metal doors suitable for installation in expanded-metal bulkheads, structural
bulkheads, and structural arches.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
D3951 Practice for Commercial Packaging
F783 Specification for Staple, Handgrab, Handle, and Stirrup Rung
2.2 Other Documents:
ABS Rules for Building and Classing Steel Vessels
AWS D1.1 Structural Welding Code
3. Classification
3.1 Expanded-metal doors are furnished in four types (see Detail “J”) as follows:
3.1.1 Type I—Right hand (RH).
3.1.2 Type II—Left hand (LH).
3.1.3 Type III—Right hand reverse (RHR).
3.1.4 Type IV—Left hand reverse (LHR).
4. Ordering Information
4.1 Orders for doors under this specification shall include this specification number and type.
5. Materials and Manufacture
5.1 Materials—See Table 1.
5.2 Manufacture:
5.2.1 Doors shall be furnished with the vertical support channels and top angle in place. A temporary brace shall be included
at the frame bottom to prevent racking.
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
Current edition approved June 1, 2012April 1, 2018. Published October 2012May 2018. Originally approved in 1987. Last previous edition approved in 20062012 as
F1072 – 94 (2006).(2012). DOI: 10.1520/F1072-94R12.10.1520/F1072-94R18.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
The last approved version of this historical standard is referenced on www.astm.org.
Available from American Bureau of Shipping (ABS), ABS Plaza, 16855 Northchase Dr., Houston, TX 77060, http://www.eagle.org.
Available from American Welding Society (AWS), 8669 NW 36 St., #130, Miami, FL 33166-6672, http://www.aws.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1072 − 94 (2018)
5.2.2 Welding shall be in accordance with AWS D1.1 Structural Welding Code or ABS Rules for Building and Classing Steel
Vessels.
6. Installation Requirements
6.1 Doors shall be fitted with rubber-tipped bumpers and a manually operated catch for holding doors in an open position. These
shall be furnished and installed by others.
6.2 Provision shall be made for the installation of a rim latch set operated by knobs on both sides. This hardware shall be
furnished and installed by others.
6.3 Padlocks shall be furnished by others.
6.4 Any holes needed in the frame for installation in expanded-metal or other types of bulkheads shall be made at installation
by others.
7. Dimensions and Tolerances
7.1 Dimensions are as indicated in Figs. 1-8 and Table 1.
7.2 Tolerance—6 ⁄16 in. (1.5 mm).
8. Workmanship, Finish, and Appearance
8.1 Doors and frames shall be free from all cracks, burrs, sharp edges, and other defects.
...