iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6583-04(2010)

(Test Method)

Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption

Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption

SIGNIFICANCE AND USE
The porosity of a paint film is closely related to the important practical characteristics of stain resistance, abrasion resistance, durability, and the hold-out of any paint subsequently applied.
This test provides a precise means for evaluating and comparing the quality of paint films, insofar as it pertains to porosity as determined on a coating applied to a nonporous substrate. Porosity measured using this test method may not be an accurate predictor of coating porosity when the coating is applied to substrate of higher absorption characteristics.
Unlike current Test Method D3258 Porosity of Paint Films, which is effective only with light colored paints, this test method is equally effective with paints of any color, both dark and light. Also unlike Test Method D3258, its results are not influenced by the hiding characteristics of the paint film.
SCOPE
1.1 This test method is applicable to air-dry architectural coatings of any type, both solvent and water-borne, and of any color, dark as well as light. It cannot be used with films that are dissolved or excessively softened by mineral oil, but practical examples of such films will be encountered rarely, if ever.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Jan-2010
ICS
87.040 - Paints and varnishes
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.42 - Architectural Coatings
Current Stage
Ref Project

Relations

Replaces
ASTM D6583-04 - Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
Effective Date
01-Feb-2010
Replaced By
ASTM D6583-13 - Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
Effective Date
01-Nov-2013
Referred By
ASTM D5324-16(2022) - Standard Guide for Testing Water-Borne Architectural Coatings
Effective Date
01-Feb-2010

Buy Standard

ASTM D6583-04(2010) - Standard Test Method for Porosity of Paint Film by Mineral Oil AbsorptionASTM D6583-04(2010) - Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
PreviousNext
Standard
ASTM D6583-04(2010) - Standard Test Method for Porosity of Paint Film by Mineral Oil Absorption
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6583 − 04 (Reapproved 2010)
StandardTest Method for
Porosity of Paint Film by Mineral Oil Absorption
This standard is issued under the fixed designation D6583; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4.2 Mineral oil is applied to the surface of the paint film,
allowed to absorb for a fixed period of time, and the excess
1.1 This test method is applicable to air-dry architectural
removed in a specified manner. The test panel is then re-
coatings of any type, both solvent and water-borne, and of any
weighed to determine the amount of mineral oil absorbed.
color, dark as well as light. It cannot be used with films that are
dissolved or excessively softened by mineral oil, but practical 4.3 Porosity is calculated from the weight ratio of absorbed
examples of such films will be encountered rarely, if ever. oil to dry paint film and from previously determined values of
non-volatile and density for the whole paint.
1.2 The values stated in SI units are to be regarded as the
standard. The values given in parentheses are for information
5. Significance and Use
only.
5.1 The porosity of a paint film is closely related to the
1.3 This standard does not purport to address all of the
important practical characteristics of stain resistance, abrasion
safety concerns, if any, associated with its use. It is the
resistance, durability, and the hold-out of any paint subse-
responsibility of the user of this standard to establish appro-
quently applied.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. 5.2 This test provides a precise means for evaluating and
comparing the quality of paint films, insofar as it pertains to
2. Referenced Documents
porosity as determined on a coating applied to a nonporous
substrate. Porosity measured using this test method may not be
2.1 ASTM Standards:
an accurate predictor of coating porosity when the coating is
D1475 Test Method For Density of Liquid Coatings, Inks,
applied to substrate of higher absorption characteristics.
and Related Products
D2369 Test Method for Volatile Content of Coatings
5.3 Unlike current Test Method D3258 Porosity of Paint
D3258 Test Method for Porosity of White or Near White
Films,whichiseffectiveonlywithlightcoloredpaints,thistest
Paint Films by Staining
method is equally effective with paints of any color, both dark
and light. Also unlike Test Method D3258, its results are not
3. Terminology
influenced by the hiding characteristics of the paint film.
3.1 Definitions:
6. Apparatus and Materials
3.1.1 porosity, n—presence of numerous minute voids in a
cured material; that is, the fraction of air by volume in the dry
6.1 Bird Type Film Applicator, 150-mm wide with a clear-
film.
ance of 150 µm.
6.2 Bird Type Film Applicator, 150-mm wide with a clear-
4. Summary of Test Method
ance of 100 µm.
4.1 The test paint is applied to a preweighed nonporous
6.3 Vacuum Drawdown Plate.
panel, air dried, then reweighed to obtain the weight of the
film.
6.4 Test Panel.
6.5 Mineral Oil, specific gravity 0.8200 to 0.8350; viscosity
6.5 to 7.8 cSt at 40°C.
This test method is under the jurisdiction of ASTM Committee D01 on Paint
and Related Coatings, Materials, andApplications and is the direct responsibility of
6.6 Absorbent Wipers.
Subcommittee D01.42 on Architectural Coatings.
Current edition approved Feb. 1, 2010. Published February 2010. Originally
approved in 2000. Last previous edition approved in 2004 as D6583 – 04. DOI:
10.1520/D6583-04R10. Transparency film AF 4300, from 3M Visual Systems Division, Austin, TX
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 78726-4599 was used in this test method. If you are aware of alternative suppliers,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM please provide this information to ASTM International Headquarters. Your com-
Standards volume information, refer to the standard’s Document Summary page on ments will receive careful consideration at a meeting of the responsible technical
the ASTM website. committee, which you may attend.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D6583 − 04 (Reapp
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D7488-11(2024)(Test Method)
Standard Test Method for Open Time of Latex Paints

SIGNIFICANCE AND USE
5.1 Latex paints dry very quickly which often causes difficulty in final appearance of painted areas, especially paints formulated below 100g/L VOC where lower amounts of solvents are in the formulated latex paint. This method is a means of determining the time available before a test paint cannot be worked into a previously painted area.
SCOPE
1.1 This test method covers a procedure to determine the length of time a latex paint remains “wet” or “open” enough to allow for brush-in and repair.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2091-96(2024)(Test Method)
Standard Test Method for Print Resistance of Lacquers

SIGNIFICANCE AND USE
4.1 An unsatisfactory appearance can result from pressure deformation of a film inherently too soft or containing residual solvent. This test method is primarily used to evaluate the resistance of a lacquer finish to printing under the conditions of packaging, shipping, and warehousing.
SCOPE
1.1 This test method covers the resistance of dried lacquer films to imprinting.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D8090-24(Test Method)
Standard Test Method for Particle Size Distribution of Paints and Pigments Using Dynamic Imaging Methods

SIGNIFICANCE AND USE
5.1 By following this test method, the particle size, particle size distribution and particle shape of particulates in liquid paint and pigment dispersions can be measured.  
5.2 Particle size, particle size distribution and particle shape have a great effect on the color, opacity and gloss of paints. Reproducing these characteristics is critical to the quality and performance of the paint produced.  
5.3 The dynamic imaging instrument is useful during manufacturing to detect oversize particles as well as the required size distribution of particles in order to provide quality and consistency from batch to batch.
SCOPE
1.1 This test method covers the determination of particle size distribution of liquid paints and pigmented liquid coatings by Dynamic Image Analysis. This method includes the reporting of particles ≥1 µm in size and up to 300 µm in size.
Note 1: Shape is used to classify particles, droplets and bubbles and is not a reporting requirement.
Note 2: The term paint(s) as used in this document includes liquid paint and liquid pigmented coatings.  
1.1.1 Some paints may be too viscous to flow through the imaging instrument without dilution which may be used to help the paint flow as long as significant contamination is not introduced into the paint.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2369-24(Test Method)
Standard Test Method for Volatile Content of Coatings

SIGNIFICANCE AND USE
4.1 This test method is the procedure of choice for determining volatiles in coatings for the purpose of calculating the volatile organic content in coatings under specified test conditions. The weight percent solids content (nonvolatile matter) may be determined by difference. This information is useful to the paint producer and user and to environmental interests for determining the volatiles emitted by coatings.
SCOPE
1.1 This test method describes a procedure for the determination of the weight percent volatile content of solventborne and waterborne coatings. Test specimens are heated at 110 °C ± 5 °C for 60 min.  
Note 1: The coatings used in these round-robin studies represented air-dried, air-dried oxidizing, heat-cured baking systems, and also included multicomponent paint systems.  
1.2 Sixty minutes at 110 °C ± 5 °C is a general purpose test method based on the precision obtained with both solventborne and waterborne coatings (see Section 9).  
1.3 This test method is viable for coatings wherein one or more parts may, at ambient conditions, contain liquid coreactants that are volatile until a chemical reaction has occurred with another component of the multi-package system.  
Note 2: Committee D01 has run round-robin studies on volatiles of multicomponent paint systems. The only change in procedure is to premix the weighed components in the correct proportions and allow the specimens to stand at room temperature for 1 h prior to placing them into the oven.  
1.4 Test Method D5095 for Determination of the Nonvolatile Content in Silanes, Siloxanes and Silane-Siloxane Blends Used in Masonry Water Repellent Treatments is the standard method for nonvolatile content of these types of materials.  
1.5 Test Methods D5403 for Volatile Content of Radiation Curable Materials is the standard method for determining nonvolatile content of radiation curable coatings, inks and adhesives.  
1.6 Test Method D6419 for Volatile Content of Sheet-Fed and Coldset Web Offset Printing Inks is the method of choice for these types of printing inks.  
1.7 This test method may not be applicable to all types of coatings. Other procedures may be substituted with mutual agreement between the producer and the user.  
Note 3: If unusual decomposition or degradation of the specimen occurs during heating, the actual time and temperature used to cure the coating in practice may be substituted for the time and temperature specified in this test method, subject to mutual agreement between the producer and the user. The U.S. EPA Reference Method 24 specifies 110 °C ± 5 °C for 1 h for coatings.
Note 4: Practice D3960 for Determining Volatile Organic Compound (VOC) Content of Paints and Related Coatings describes procedures and calculations and provides guidance on selecting test methods to determine VOC content of solventborne and waterborne coatings.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D2064-24(Test Method)
Standard Test Method for Print Resistance of Architectural Paints

SIGNIFICANCE AND USE
5.1 The ability of a coating to resist printing is important because its appearance is adversely affected if the smoothness of the coating film is altered by contact with another surface, particularly one with a texture. Interior paint systems, particularly gloss and semigloss on window sills and other horizontal surfaces, often have objects such as flower pots placed on them that may tend to leave a permanent impression. This tendency for a paint film to “print” is a function of the hardness of the coating, the pressure, temperature, humidity, and the duration of time that the object is in contact with the painted surface.
SCOPE
1.1 This test method covers an accelerated procedure for evaluating the print resistance of architectural paints. It differs from print resistance Test Method D2091 in that the latter is concerned with lacquer finishes under packaging, shipping, and warehousing conditions, whereas this test method is concerned with decorative coatings undergoing random on-site pressure contact.  
Note 1: Printing should not be confused with blocking, which is measured in Test Method D4946. The former relates to the indentation of a surface, and the latter, the sticking together of two surfaces.  
1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4213-24(Test Method)
Standard Test Method for Scrub Resistance of Paints by Abrasion Weight Loss

SIGNIFICANCE AND USE
4.1 Interior paint films often become soiled, especially near doorways, windows, and play areas, and frequently need to be cleaned by scrubbing. This test method covers the determination of the relative resistance of paints to erosion when scrubbed.  
4.2 The precision of scrub resistance measurements in absolute physical values, such as Test Methods D2486 (cycles-to-failure or this test method, microlitres per 100 cycles), is poor due to the relatively large effect of subtle and difficult-to-control variables in test conditions. The test method described herein minimizes this problem by using a standard calibration panel as an integral part of each scrubbing operation and relating its weight loss to that of the paint film under test to establish the latter's scrub resistance.
Note 1: The numerical scrub resistance values obtained by this test method are of significance only in relation to the specific calibration panel types with which the value is obtained. Thus, for example, a scrub resistance value of 83 with a Type X calibration panel would be reported as 83X.  
4.3 Results obtained by this test method do not necessarily represent the scrub resistance that might be determined if the test film is allowed to dry before testing appreciably longer than the seven-day period specified herein.  
4.4 Results obtained by this test method do not necessarily relate to ease of soil or stain removal (also referred to as “cleanability” or “cleansability”). To test for those characteristics use Test Methods D3450 and D4828.
FIG. 1 Alignment of Panels for Scrubbing
SCOPE
1.1 This test method covers an accelerated procedure for determining the resistance of paints to erosion caused by scrubbing. (Note: The term wet abrasion is sometimes used for scrubbing, and wet abrasion resistance or scrubbability for scrub resistance.) Although scrub resistance tests are intended primarily for interior coatings, they are sometimes used with exterior coatings as an additional measure of film performance.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D3023-98(2024)(Practice)
Standard Practice for Determination of Resistance of Factory-Applied Coatings on Wood Products to Stains and Reagents

SIGNIFICANCE AND USE
3.1 When used in conjunction with Guide D333, this practice will provide a comprehensive evaluation of resistance to stains caused by chemical reagents and household chemicals.  
3.2 This practice applies only to coatings applied in sufficient quantity to form a continuous film. It is recommended that the dry film thickness of the coating under test be reported.  
3.3 Results from stain tests conducted in accordance with this practice distinguish differences between coatings.
SCOPE
1.1 This practice covers evaluation of clear factory-applied coating systems on wood substrates.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6441-05(2024)(Test Method)
Standard Test Methods for Measuring the Hiding Power of Powder Coatings

SIGNIFICANCE AND USE
5.1 Contrast ratio at a specified film thickness is a useful hiding power parameter for production control and purchasing specifications.  
5.2 The greater the hiding power, the less coating is required per unit area to obtain adequate hiding. Knowledge of hiding power is therefore important in regard to coating costs and for comparing coating value.
SCOPE
1.1 These test methods determine and report the hiding power of a powder coating with respect to two parameters:  
1.1.1 Test Method A—Contrast Ratio at a given film thickness  
1.1.2 Test Method B—Film thickness at 0.98 (98 %) contrast ratio.
Note 1: The measured parameters follow powder coating industry practice by measuring hiding power in relation to film thickness, rather than the “Spreading Rate” function employed in Test Methods D344 and D2805 and other hiding power test methods.
Note 2: Hiding power is photometrically defined as the spreading rate at 0.98 contrast ratio. See definitions of spreading rate and hiding power in Terminology D16, D2805, and the Paint and Coatings Testing Manual.
Note 3: The contrast ratio 0.98 is conventionally accepted in the coatings industry as representing “complete” hiding for reflectometric hiding power measurements. But visually, as well as photometrically, it is slightly less than complete.  
1.2 These test methods cover the determination of the hiding power of powder coatings applied by electrostatic spraying.  
1.3 These test methods determine hiding power by means of reflectometric and thickness gauge measurements. They are limited to coatings having a minimum CIE-Y reflectance of 15 %.  
1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM D4958-24(Test Method)
Standard Test Method for Comparison of the Brush Drag of Latex Paints

SIGNIFICANCE AND USE
5.1 As the brush drag of a paint increases, any natural tendency on the part of the painter to overspread the paint is reduced. When all other factors are held constant, increased brush drag will result in greater film thickness with consequent improvement in durability and hiding. Conversely, sometimes it might be preferred to have a lesser degree of brush drag for easier application (that is, the amount of time and effort in applying a paint to a specific area is reduced with a lesser degree of brush drag).  
5.2 This test method provides a standardized brushout procedure for the evaluation of brush drag as an alternative to customary informal ad hoc procedures. Its objective is to maximize the reliability and precision with which this characteristic may be determined.
Note 1: The brush drag of paints is directly related to their high-shear viscosity. There is generally good rank order agreement between results obtained by this method and Test Method D4287. The sensitivity of this brushout method has been found sufficient to distinguish between brushability corresponding to high-shear viscosity differences not lower than 0.3 poise (0.03 Pa.s). Round robin data show that rank order agreement between the brushout and viscometric methods is poor when both latex and solvent-borne paints are part of the same comparison group. This is the result of these two paint types having markedly different rheological properties that affect the relative perception of brush drag.3
SCOPE
1.1 This test method is a standardized brushout procedure for comparing the brush drag of architectural type solvent-borne paints.  
1.2 With slight modifications this test method is also applicable to solvent-borne paints.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2794-93(2024)(Test Method)
Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)

SIGNIFICANCE AND USE
5.1 Coatings attached to substrates are subjected to damaging impacts during the manufacture of articles and their use in service. In its use over many years, this test method for impact resistance has been found to be useful in predicting the performance of organic coatings for their ability to resist cracking caused by impacts.
SCOPE
1.1 This test method covers a procedure for rapidly deforming by impact a coating film and its substrate and for evaluating the effect of such deformation.  
1.2 This test method should be restricted to testing in only one laboratory when numerical values are used because of the poor reproducibility of the method. Interlaboratory agreement is improved when ranking is used in place of numerical values.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off