iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM E929-83(2009)

(Test Method)

Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment (Withdrawn 2014)

Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment (Withdrawn 2014)

SIGNIFICANCE AND USE
This method is used to document the ability of solid waste resource recovery separators to concentrate or classify a particular component (or components) present in solid waste.
The purity determined in this way is used to calculate the recovery achieved by a separator as another measure of its performance, according to Test Method E1108.
SCOPE
1.1 This test method covers the determination of the composition of a materials stream in a solid waste resource recovery processing facility. The composition is determined with respect to one or more defined components. The results are used for determining the purity resulting from the operation of one or more separators, and in conjunction with Test Method E1108 used to measure the efficiency of a materials separation device.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For hazard statements, see Section 7.
WITHDRAWN RATIONALE
This test method covered the determination of the energy and power requirements of processing equipment using an electrical metering system.
Formerly under the jurisdiction of Committee D34 on Waste Management, this test method was withdrawn in May 2014. This standard is being withdrawn without replacement due to its limited use by industry.

General Information

Status
Withdrawn
Publication Date
31-Aug-2009
Withdrawal Date
20-May-2014
ICS
03.100.50 - Production. Production management
Technical Committee
D34 - Waste Management
Drafting Committee
D34.03 - Treatment, Recovery and Reuse
Current Stage
Ref Project

Relations

Replaces
ASTM E929-83(2005) - Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment
Effective Date
01-Sep-2009
Referred By
ASTM D5681-22e1 - Standard Terminology for Waste and Waste Management
Effective Date
01-Sep-2009
Referred By
ASTM E959-83(2018) - Standard Test Method for Characterizing the Performance of Refuse Size-Reduction Equipment
Effective Date
01-Sep-2009

Buy Standard

ASTM E929-83(2009) - Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment (Withdrawn 2014)ASTM E929-83(2009) - Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment (Withdrawn 2014)
PreviousNext
Standard
ASTM E929-83(2009) - Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment (Withdrawn 2014)
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E929 − 83(Reapproved 2009)
Standard Test Method for
Measuring Electrical Energy Requirements of Processing
1
Equipment
This standard is issued under the fixed designation E929; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.4 gross energy— energy usage of a piece of equipment
operating under loaded conditions as measured using an
1.1 This test method covers the determination of the energy
electrical metering system.
and power requirements of processing equipment using an
electrical metering system. 2.5 gross power— power requirement of a piece of equip-
ment under loaded conditions.
1.2 This test method can be used to measure energy and
power requirements of processing equipment driven by an 2.6 loaded condition— equipment doing processing work
electrical motor operating on alternating current. on solids, liquids, or gases, or all of these, (for example,
moving material, changing its characteristics, or separating it
1.3 This test method includes instructions for installation
into different streams).
and checkout of the energy metering system, procedures for
measuring and recording energy usage, and methods for 2.7 net power—the difference between gross power and
calculating the average gross power, average freewheeling freewheeling power; net power is the power required for
power, and average net power requirements of processing processing.
equipment.
2.8 specific energy— energy consumption expressed on the
1.4 The values stated in SI units are to be regarded as basis of unit mass of throughput.
standard. No other units of measurement are included in this
2.9 unloaded condition—equipment not doing processing
standard.
work (for example, moving, changing the characteristics of, or
1.5 This standard does not purport to address all of the
separating materials), but operating in a freewheeling, or
safety concerns, if any, associated with its use. It is the
idling, condition.
responsibility of the user of this standard to establish appro-
3. Summary of Test Method
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. For hazard 3.1 An electrical metering system is installed and checked.
statements, see Section 6.
3.2 Themeteringinstrumentationandprocessingequipment
is allowed to warmup.
2. Terminology Definitions
3.3 Usingtheelectricalmeteringsystem,theenergyusedby
2.1 electrical metering system—a system composed of cur-
the processing equipment under no-load and loaded conditions
rent and potential transformers and a wattmeter electrically
is measured and recorded.
connected in such a manner so as to measure the energy usage
3.4 The average gross power, average freewheeling power,
of a piece of equipment driven by an electric motor.
andaveragenetpowerrequiredbytheequipmentiscalculated.
2.2 freewheeling condition—a piece of equipment under an
4. Significance and Use
unloaded condition wherein the electrical energy is dissipated
due to friction and windage.
4.1 Energy usage and power requirements of processing
equipment are important from the standpoint of determining if
2.3 freewheeling power—power requirement of a piece of
equipment is operating within specification and meeting per-
equipment under unloaded, or freewheeling, conditions.
formance criteria.
4.2 Havingdeterminedtheenergyusageandpowerrequire-
1
ments of the processing equipment using this method, specific
This test method is under the jurisdiction ofASTM Committee D34 on Waste
ManagementandisthedirectresponsibilityofSubcommitteeD34.03onTreatment,
energy may be calculated, with the use of system throughput,
Recovery and Reuse.
and used as one criterion to compare the performance of
Current edition approved Sept. 1, 2009. Published November 2009. Originally
similar pieces of equipment operating under similar operating
approved in 1983. Last previous edition approved in 2005 as E929-83(2005). DOI:
10.1520/E0929-83R09. conditions.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E929 − 83 (2009)
4.3 Measurements of energy usage can be used for the 8. Procedure
purposeofidentifyinginefficientelectricalmotorsandprocess-
8.1 Meter Installation:
ing equipment.
8.1.1 For the piece of equipment to be tested, determine the
type of electrical service (for example, single-phase two-wire,
5. Apparatus
three-phase three-wire), voltage requirements, full load power,
5.1 Calibrated Watthour Meter.
and current rating of the motor from the motor nameplate or
5.2
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM E1107-15(2023)(Test Method)
Standard Test Method for Measuring the Throughput of Resource-Recovery Unit Operations

SIGNIFICANCE AND USE
5.1 This test method is used to document the mass flow rate of a resource recovery unit operation in a plant and as a means of relating operation to design objectives.  
5.2 This test method is also used in conjunction with measurements of the performance of materials separators (particularly recovery and purity). As such, throughput should not generally be measured by sampling the feed since this may change its performance. Processing equipment that does not perform separations can be sampled at either the feed or product streams.
SCOPE
1.1 This test method is for measuring the throughput, or mass flow rate, of a resource-recovery unit operation, or series of unit operations.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exception—Paragraph 9.1.2 indicates the equivalent weight in pounds for samples with particle size greater than 90 mm.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1107-15(Test Method)
Standard Test Method for Measuring the Throughput of Resource-Recovery Unit Operations

SIGNIFICANCE AND USE
5.1 This test method is used to document the mass flowrate of a resource recovery unit operation in a plant and as a means of relating operation to design objectives.  
5.2 This test method is also used in conjunction with measurements of the performance of materials separators (particularly recovery and purity). As such, throughput should not generally be measured by sampling the feed since this may change its performance. Processing equipment that does not perform separations can be sampled at either the feed or product streams.
SCOPE
1.1 This test method is for measuring the throughput, or mass flowrate, of a resource-recovery unit operation, or series of unit operations.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exception—Section 9.1.2 indicates the equivalent weight in pounds for samples with particle size greater than 90 mm.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in Section 7.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1107-10(Test Method)
Standard Test Method for Measuring the Throughput of Resource-Recovery Unit Operations

SIGNIFICANCE AND USE
This test method is used to document the mass flowrate of a resource recovery unit operation in a plant and as a means of relating operation to design objectives.
This test method is also used in conjunction with measurements of the performance of materials separators (particularly recovery and purity). As such, throughput should not generally be measured by sampling the feed since this may change its performance. Processing equipment that does not perform separations can be sampled at either the feed or product streams.
SCOPE
1.1 This test method is for measuring the throughput, or mass flowrate, of a resource-recovery unit operation, or series of unit operations.
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.2.1 Exception—Section 9.1.2 indicates the equivalent weight in pounds for samples with particle size greater than 90 mm.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in Section 7.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E929-83(2005)(Test Method)
Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment

SCOPE
1.1 This test method covers the determination of the energy and power requirements of processing equipment using an electrical metering system.
1.2 This test method can be used to measure energy and power requirements of processing equipment driven by an electrical motor operating on alternating current.
1.3 This test method includes instructions for installation and checkout of the energy metering system, procedures for measuring and recording energy usage, and methods for calculating the average gross power, average freewheeling power, and average net power requirements of processing equipment.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For hazard statements, see Section .

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E929-83(1999)(Test Method)
Standard Test Method for Measuring Electrical Energy Requirements of Processing Equipment

SCOPE
1.1 This test method covers the determination of the energy and power requirements of processing equipment using an electrical metering system.  
1.2 This test method can be used to measure energy and power requirements of processing equipment driven by an electrical motor operating on alternating current.  
1.3 This test method includes instructions for installation and checkout of the energy metering system, procedures for measuring and recording energy usage, and methods for calculating the average gross power, average freewheeling power, and average net power requirements of processing equipment.  
1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For hazard statements, see Section 6.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM E1107-86(1996)e1(Test Method)
Standard Test Method for Measuring the Throughput of Resource-Recovery Unit Operations

SCOPE
1.1 This method is for measuring the throughput, or mass flowrate, of a resource-recovery unit operation, or series of unit operations.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in Section 7.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1107-86(2004)(Test Method)
Standard Test Method for Measuring the Throughput of Resource-Recovery Unit Operations

SIGNIFICANCE AND USE
This test method is used to document the mass flowrate of resource recovery unit operations as a means of documenting the operating of a plant (or portions of a plant) and as a means of relating operation to design objectives.
This test method is also used in conjunction with measurements of the performance of materials separators (particularly recovery and purity). As such, throughput should not generally be measured by sampling the feed since this may change its performance. Processing equipment that does not perform separations can be sampled at either the feed or product streams.
SCOPE
1.1 This test method is for measuring the throughput, or mass flowrate, of a resource-recovery unit operation, or series of unit operations.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in Section .

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM E1107-15(2023)(Test Method)
Standard Test Method for Measuring the Throughput of Resource-Recovery Unit Operations

SIGNIFICANCE AND USE
5.1 This test method is used to document the mass flow rate of a resource recovery unit operation in a plant and as a means of relating operation to design objectives.  
5.2 This test method is also used in conjunction with measurements of the performance of materials separators (particularly recovery and purity). As such, throughput should not generally be measured by sampling the feed since this may change its performance. Processing equipment that does not perform separations can be sampled at either the feed or product streams.
SCOPE
1.1 This test method is for measuring the throughput, or mass flow rate, of a resource-recovery unit operation, or series of unit operations.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.2.1 Exception—Paragraph 9.1.2 indicates the equivalent weight in pounds for samples with particle size greater than 90 mm.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in Section 7.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM E1765-16(2023)(Practice)
Standard Practice for Applying Analytical Hierarchy Process (AHP) to Multiattribute Decision Analysis of Investments Related to Projects, Products, and Processes

SIGNIFICANCE AND USE
5.1 The AHP method allows you to generate a single measure of desirability for project/product/process alternatives with respect to multiple attributes (qualitative and quantitative). By contrast, life-cycle cost (Practice E917), net savings (Practice E1074), savings-to-investment ratio (Practice E964), internal rate-of-return (Practice E1057), and payback (Practice E1121) methods all require you to put a monetary value on benefits and costs in order to include them in a measure of project/product/process worth.  
5.2 Use AHP to evaluate a finite and generally small set of discrete and predetermined options or alternatives. Specific AHP applications are ranking and choosing among alternatives. For example, rank alternative building locations with AHP to see how they measure up to one another, or use AHP to choose among building materials to see which is best for your application.  
5.3 Use AHP if no single alternative exhibits the most preferred available value or performance for all attributes. This is often the result of an underlying trade-off relationship among attributes. An example is the trade-off between low desired energy costs and large glass window areas (which may raise heating and cooling costs while lowering lighting costs).  
5.4 Use AHP to evaluate alternatives whose attributes are not all measurable in the same units. Also use AHP when performance relative to some or all of the attributes is impractical, impossible, or too costly to measure. For example, while life-cycle costs are directly measured in monetary units, the number and size of offices are measured in other units, and the public image of a building may not be practically measurable in any unit. To help you choose among candidate buildings with these diverse attributes, use AHP to evaluate your alternatives.  
5.5 The AHP method is well-suited for application to a variety of sustainability-related topics. Guide E2432 states when applying the concept of sustainability, it is necessary ...
SCOPE
1.1 This practice presents a procedure for calculating and interpreting AHP scores of a project’s/product’s/process’ total overall desirability when making capital investment decisions.3 Projects include design, construction, operation, and disposal of commercial and residential buildings and other engineered structures.4 Products include materials, components, systems, and equipment.5 Processes include procurement, materials management, work flow, fabrication and assembly, quality control, and services.  
1.2 In addition to monetary benefits and costs, the procedure allows for the consideration of characteristics or attributes which decision makers regard as important, but which are not readily expressed in monetary terms. Examples of such attributes that pertain to the selection among project/product/process alternatives are: a construction projects’s building alternatives whose nonmonetary attributes are location/accessibility, site security, maintainability, quality of the sound and visual environment, and image to the public and occupants; building products based on their economic and environmental performance; and sustainability-related issues for key construction processes that address environmental needs, while considering project safety, cost, and schedule.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    20 pages
    English language
    sale 15% off
ASTM
ASTM F1675-13(2022)(Practice)
Standard Practice for Life-Cycle Cost Analysis of Plastic Pipe Used for Culverts, Storm Sewers, and Other Buried Conduits

SIGNIFICANCE AND USE
5.1 LCC analysis is an economic method to evaluate alternatives that are characterized by differing cash flows over the designated project design life. The method entails calculating the LCC of each alternative capable of satisfying the functional requirements of the project and comparing them to determine which have the lowest estimated LCC over the project design life.  
5.2 The LCC method is particularly suitable for determining whether the higher initial cost of an alternative is economically justified by reductions in future costs (for example, operating maintenance, rehabilitation, or replacement) when compared to an alternative with lower initial costs but higher future costs. If a design alternative has both a lower initial cost and lower future costs than other alternatives, an LCC analysis is not necessary to show the former is the economically preferable choice.
SCOPE
1.1 This practice establishes a procedure for using life cycle cost (LCC) analysis techniques to evaluate alternative drainage system designs, using plastic pipe that satisfy the same functional requirements.  
1.2 The LCC technique measures the present value of all relevant costs to install, operate, and maintain alternative drainage systems such as engineering, construction, maintenance, rehabilitation, or replacement over a specified period of time. The practice also accommodates any remaining residual or salvage value.  
1.3 The decision maker, using the results of the LCC analysis, can then identify the alternative(s) with the lowest estimated total cost based on the present value of all costs.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off