ASTM F912-11(2017)
(Specification)Standard Specification for Alloy Steel Socket Set Screws
Standard Specification for Alloy Steel Socket Set Screws
ABSTRACT
This specification covers the requirements and corresponding test methods for quenched and tempered alloy steel socket set screws (SSS) having sizes of M1.6 through M24, hardnesses of 45 to 53 HRC, and belonging to ISO 898/5 property class 45H. These set screws are intended for compression applications only and are not customarily subjected to embrittlement tests. The screws shall be fabricated to a fine grain practice in standard surface finishes, and optional protective coating as specified in the purchase order. Sampled specimens shall undergo heat and product analysis for measurements of the chemical content for carbon, phosphorus, and sulfur. Appropriate tests shall also be performed to analyze the conformance of the screws to mechanical and other property requirements such as torque and torsional strength, microhardness, decarburization, and surface discontinuities.
SCOPE
1.1 This specification covers the requirements for quenched and tempered alloy steel socket-set screws (SSS) in nominal diameters 0.060 through 2 in. having hardnesses 45 to 53 HRC.
1.2 These set screws are intended for compression applications only and are not customarily subjected to embrittlement tests. For tensile applications, consult with the manufacturer for proper alloy and hardness.
1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: A complete metric companion to Specification F912 has been developed—F912M; therefore, no metric equivalents are shown in this Specification.
1.4 The hazard statement pertains only to the test method section, Section 11 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F912 −11 (Reapproved 2017)
Standard Specification for
1
Alloy Steel Socket Set Screws
ThisstandardisissuedunderthefixeddesignationF912;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* E3 Guide for Preparation of Metallographic Specimens
E112 Test Methods for Determining Average Grain Size
1.1 This specification covers the requirements for quenched
E384 Test Method for Microindentation Hardness of Mate-
and tempered alloy steel socket-set screws (SSS) in nominal
rials
diameters0.060through2in.havinghardnesses45to53HRC.
F606/F606M Test Methods for Determining the Mechanical
1.2 These set screws are intended for compression applica-
Properties of Externally and Internally Threaded
tions only and are not customarily subjected to embrittlement
Fasteners, Washers, Direct Tension Indicators, and Rivets
tests. For tensile applications, consult with the manufacturer
F788 Specification for Surface Discontinuities of Bolts,
for proper alloy and hardness.
Screws, and Studs, Inch and Metric Series
F1470 Practice for Fastener Sampling for Specified Me-
1.3 The values stated in inch-pound units are to be regarded
as standard. No other units of measurement are included in this chanical Properties and Performance Inspection
F2328 Test Method for Determining Decarburization and
standard.
Carburization in Hardened and Tempered Threaded Steel
NOTE 1—Acomplete metric companion to Specification F912 has been
Bolts, Screws, Studs, and Nuts
developed—F912M; therefore, no metric equivalents are shown in this
3
2.2 ASME Standards:
Specification.
4
B18.3 Socket Cap, Shoulder and Set Screw, Inch Series
1.4 The hazard statement pertains only to the test method
B18.24 Part Identifying Number (PIN) Code System Stan-
section, Section 11 of this specification.Thisstandarddoesnot
dard for B18 Fastener Products
purport to address all of the safety concerns, if any, associated
with its use. It is the responsibility of the user of this standard
3. Ordering Information
to establish appropriate safety and health practices and
3.1 Orders for material under this specification shall include
determine the applicability of regulatory limitations prior to
the following information:
use.
3.1.1 Quantity (number of screws).
1.5 This international standard was developed in accor-
3.1.2 Dimensions, including nominal thread designation,
dance with internationally recognized principles on standard-
threads per inch, nominal screw length (inches) and point
ization established in the Decision on Principles for the
configuration. A standard part number may be used for this
Development of International Standards, Guides and Recom-
definition.
mendations issued by the World Trade Organization Technical
3.1.3 Name of the screw (SSS).
Barriers to Trade (TBT) Committee.
3.1.4 Coating, if required. See 4.4.
3.1.5 Certification, if required. See 14.1.
2. Referenced Documents
3.1.6 ASTM designation and year of issue.
2
2.1 ASTM Standards:
3.1.7 Any special or supplemental requirements.
A751 Test Methods, Practices, and Terminology for Chemi-
3.1.8 For establishment of a part identifying system, see
cal Analysis of Steel Products
ASME B18.24.
4. Materials and Manufacture
1
This specification is under the jurisdiction of ASTM Committee F16 on
Fasteners and is the direct responsibility of Subcommittee F16.02 on Steel Bolts,
4.1 The screws shall be fabricated from alloy steel made to
Nuts, Rivets and Washers.
fine grain practice. In the event of controversy over grain size,
Current edition approved June 1, 2017. Published June 2017. Originally
approved in 1986. Last previous edition approved in 2011 as F912 – 11. DOI:
3
10.1520/F0912-11R17. Available from American Society of Mechanical Engineers (ASME), ASME
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM www.asme.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.