ASTM C1618-05(2013)
(Test Method)Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure
Standard Test Method for Concrete Sanitary Sewer Pipe by Negative (Vacuum) or Positive Air Pressure
SIGNIFICANCE AND USE
5.1 This is a quality control test performed at the manufacturing plant to establish that the finished, shippable pipe meets the leakage limits stated in the specifications.
SCOPE
1.1 This test method covers procedures for testing of precast concrete pipe sections, prior to delivery, where maximum field leakage rates are specified.
1.2 Tests described in this standard are intended to be used at the point of manufacture of the concrete pipe and are not intended for testing installed pipe (for field tests see Practices C924, C969, and C1214). The user of this specification is advised that individual or multiple pipe sections may be tested for the purpose of testing the pipe barrel and additionally the joints in straight alignment when multiple pipe sections are tested.
1.3 The two leakage rates shown, which were used in calculating the test times, were chosen based on two generally accepted field air and vacuum test criteria. Test times are based on leakage rates and therefore are proportional only to the pipe diameter and are constant for any length of test pipe or pipeline.
1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard. Note 1—The availability of this test procedure for concrete pipe varies from location to location. Check with local supplier(s) for availability and recommendations.
1.5 This standard does not purport to address all the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish the appropriate safety and health practices and to determine the applicability of regulatory limitations prior to its use. See Section 6 for specific safety precautions.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C1618 − 05(Reapproved 2013)
Standard Test Method for
Concrete Sanitary Sewer Pipe by Negative (Vacuum) or
1
Positive Air Pressure
This standard is issued under the fixed designation C1618; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 Thistestmethodcoversproceduresfortestingofprecast 2.1 ASTM Standards:
concrete pipe sections, prior to delivery, where maximum field C822 Terminology Relating to Concrete Pipe and Related
leakage rates are specified. Products
C924 Practice for Testing Concrete Pipe Sewer Lines by
1.2 Tests described in this standard are intended to be used
Low-Pressure Air Test Method
at the point of manufacture of the concrete pipe and are not
C969 Practice for Infiltration and Exfiltration Acceptance
intended for testing installed pipe (for field tests see Practices
Testing of Installed Precast Concrete Pipe Sewer Lines
C924, C969, and C1214). The user of this specification is
C1214 Test Method for Concrete Pipe Sewerlines by Nega-
advised that individual or multiple pipe sections may be tested
tive Air Pressure (Vacuum) Test Method
for the purpose of testing the pipe barrel and additionally the
joints in straight alignment when multiple pipe sections are
3. Terminology
tested.
3.1 Definitions—For definitions of terms related to precast
1.3 The two leakage rates shown, which were used in
concrete pipe, see Terminology C822.
calculating the test times, were chosen based on two generally
4. Summary of Test Method
accepted field air and vacuum test criteria. Test times are based
on leakage rates and therefore are proportional only to the pipe
4.1 The pipe to be tested shall be sealed at the outer ends
diameter and are constant for any length of test pipe or
withsuitableairtightbulkheads.Themanufacturershallchoose
pipeline.
to use either low-pressure air or negative pressure air (vacuum)
test methods to evaluate the condition of the pipe before
1.4 The values stated in inch-pound units are to be regarded
delivery. The change in the internal pressure during a specified
as standard. No other units of measurement are included in this
time is used to determine the acceptability of the pipe.
standard.
NOTE 1—The availability of this test procedure for concrete pipe varies 5. Significance and Use
from location to location. Check with local supplier(s) for availability and
5.1 This is a quality control test performed at the manufac-
recommendations.
turing plant to establish that the finished, shippable pipe meets
1.5 This standard does not purport to address all the safety
the leakage limits stated in the specifications.
concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish the appropriate safety
6. Safety Precautions
and health practices and to determine the applicability of
6.1 Theuserofthisspecificationisadvisedofthefollowing:
regulatory limitations prior to its use.SeeSection6forspecific
6.1.1 This test may be dangerous if a pipe is not prepared
safety precautions.
properly and proper procedures are not followed.
6.1.2 No one should be allowed near the ends of the pipe or
test bulkheads during the test.
1
This test method is under the jurisdiction of ASTM Committee C13 on
Concrete Pipe and is the direct responsibility of Subcommittee C13.09 on Methods
2
of Test. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Feb. 1, 2013. Published February 2013. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2005. Last previous edition approved in 2005 as C1618 – 05. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1618-05R13. the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1618 − 05 (2013)
TABLE 1 Test Times For Negative Pressure Air Test, Seconds
7. Apparatus
NOTE 1—A pressure increase of 0.1083 in. Hg was chosen because it
7.1 For positive air pressure test, one bulkhead shall include
l
corresponds to a change in water column height of approximately l ⁄2 in.
a remote controlled valve that will release the internal test
(1.4725 in. exactly) and a change in manometer oil column height
pressure.
l
(specific gravity 2.945) of ⁄2 in. Test times shall be increased proportion-
ally if larger changes in the height of the manometer column are required.
7.2 For the low-pressure air test, tie rods or an external test
frame that is de
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.