ASTM C5-18

Standard Specification for Quicklime for Structural Purposes

ABSTRACT
This specification covers all classes of quicklime such as crushed lime, granular lime, ground lime, lump lime, pebble lime, and pulverized lime, used for structural purposes. The quicklime shall conform to the chemical composition requirements specified. Quicklime shall be slaked and aged in accordance with printed directions of the manufacturer. The resulting lime putty shall be stored until cool. Test methods shall be performed for the chemical requirements, plasticity and residue requirements.
SCOPE
1.1 This specification covers all classes of quicklime such as crushed lime, granular lime, ground lime, lump lime, pebble lime, and pulverized lime, used for structural purposes.  
1.2 The values stated in inch-pound units are to be regarded as standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 30-Sep-2018
• ICS: 91.100.10 - Cement. Gypsum. Lime. Mortar
• Technical Committee: C07 - Lime and Limestone
• Drafting Committee: C07.02 - Specifications and Guidelines

Relations

• Refers: ASTM C110-14 - Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
• Effective Date: 01-Dec-2014
• Refers: ASTM C110-14e1 - Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
• Effective Date: 01-Dec-2014
• Refers: ASTM C110-15 - Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
• Effective Date: 01-Jun-2015
• Refers: ASTM C110-15e1 - Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
• Effective Date: 01-Jun-2015
• Refers: ASTM C110-16 - Standard Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
• Effective Date: 01-Dec-2016
• Refers: ASTM C50/C50M-13(2019) - Standard Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products
• Effective Date: 01-Dec-2019
• Refers: ASTM C51-18 - Standard Terminology Relating to Lime and Limestone (as used by the Industry)
• Effective Date: 01-Dec-2018

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C5 − 18
Standard Specification for
1
Quicklime for Structural Purposes
This standard is issued under the fixed designation C5; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 3. Terminology
3.1 Definitions—Unless otherwise specified, for definitions
1.1 This specification covers all classes of quicklime such as
crushed lime, granular lime, ground lime, lump lime, pebble of terms used in this standard, refer to Terminology C51.
lime, and pulverized lime, used for structural purposes.
4. Chemical Composition
1.2 The values stated in inch-pound units are to be regarded
as standard.
4.1 The quicklime shall conform to the following require-
ments as to chemical composition, calculated on a nonvolatile
1.3 This standard does not purport to address all of the
basis:
safety concerns, if any, associated with its use. It is the
Calcium Magnesium
responsibility of the user of this standard to establish appro-
Lime Lime
priate safety, health, and environmental practices and deter-
Calcium oxide, min, % 75
mine the applicability of regulatory limitations prior to use.
Magnesium oxide, min, % 20
Calcium and magnesium oxide, min, % 95 95
1.4 This international standard was developed in accor-
Silica, alumina, and oxide of iron, max, % 5 5
dance with internationally recognized principles on standard-
Carbon dioxide, max, %:
ization established in the Decision on Principles for the
If sample is taken at place of manufacture 3 3
If sample is taken at any other place 10 10
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
5. Residue
Barriers to Trade (TBT) Committee.
5.1 The quicklime shall contain no more than 15 weight %
2. Referenced Documents
of residue as determined by the Test Methods C110 Slaking
2
Rate of Quicklime test procedure.
2.1 ASTM Standards:
C25 Test Methods for Chemical Analysis of Limestone,
6. General Requirements
Quicklime, and Hydrated Lime
C50/C50M Practice for Sampling, Sample Preparation,
6.1 Quicklime shall be slaked and aged in accordance with
Packaging, and Marking of Lime and Limestone Products
the printed directions of the manufacturer. The resulting lime
C51 Terminology Relating to Lime and Limestone (as Used
putty shall be stored until cool.
by the Industry)
6.2 Lime putty prepared in accordance with Appendix
C110 Test Methods for Physical Testing of Quicklime,
X1.4.2 must conform to the requirements of Specification
Hydrated Lime, and Limestone
C1489.
C1489 Specification for Lime Putty for Structural Purposes
E11 Specification for Woven Wire Test Sieve Cloth and Test
7. Sampling, Inspection, and So Forth
Sieves
7.1 The sampling, inspection, rejection, retesting,
packaging, and marking shall be conducted in accordance with
1
This specification is under the jurisdiction of ASTM Committee C07 on Lime Methods C50/C50M.
and Limestone and is the direct responsibility of Subcommittee C07.02 on
Specifications and Guidelines.
8. Test Methods
Current edition approved Oct. 1, 2018. Published November 2018. Originally
approved in 1913. Last previous edition approved in 2010 as C5 – 10. DOI:
8.1 Conformance to chemical requirements shall be deter-
10.1520/C0005-18.
2 mined in accordance with Test Methods C25.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
8.2 Conformance to residue requirements shall be deter-
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. mined in accordance with Test Methods C110.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C5 − 18
9. Keywords
9.1 building (structural); calcium oxide; dolomitic lime;
high calcium lime; lime putty; magnesium oxide; plasticity;
quicklime; residue; slaking
APPENDIX
(Nonmandatory Information)
X1. SLAKING AND PREPARATION OF LIME PUTTY
X1.1 Introduction available for immediate use—a hose throwing a good stream,
if possible. Watch the lime constantly. At the slightest appear-
X1.1.1 Quicklime can never be used as such for structural
ance of escaping steam, mix thoroughly and quickly, and add
purposes; it must always be slaked first. Since the method of
enough
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C5 − 10 C5 − 18
Standard Specification for
1
Quicklime for Structural Purposes
This standard is issued under the fixed designation C5; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers all classes of quicklime such as crushed lime, granular lime, ground lime, lump lime, pebble lime,
and pulverized lime, used for structural purposes.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C25 Test Methods for Chemical Analysis of Limestone, Quicklime, and Hydrated Lime
C50C50/C50M Practice for Sampling, Sample Preparation, Packaging, and Marking of Lime and Limestone Products
C51 Terminology Relating to Lime and Limestone (as used by the Industry)
C110 Test Methods for Physical Testing of Quicklime, Hydrated Lime, and Limestone
C1489 Specification for Lime Putty for Structural Purposes
E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves
3. Terminology
3.1 Definitions—Unless otherwise specified, for definitions of terms used in this standard, refer to Terminology C51.
4. Chemical Composition
4.1 The quicklime shall conform to the following requirements as to chemical composition, calculated on a nonvolatile basis:
Calcium Lime Magnesium Lime
Calcium oxide, min, % 75
Magnesium oxide, min, % 20
Calcium and magnesium oxide, 95 95
min, %
Silica, alumina, and oxide of iron, 5 5
max, %
Carbon dioxide, max, %:
If sample is taken at place of 3 3
manufacture
If sample is taken at any other 10 10
place
1
This specification is under the jurisdiction of ASTM Committee C07 on Lime and Limestone and is the direct responsibility of Subcommittee C07.02 on Specifications
and Guidelines.
Current edition approved June 1, 2010Oct. 1, 2018. Published July 2010November 2018. Originally approved in 1913. Last previous edition approved in 20092010 as
C5–03(2009).C5 – 10. DOI: 10.1520/C0005-10.10.1520/C0005-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
C5 − 18
Calcium Magnesium
Lime Lime
Calcium oxide, min, % 75
Magnesium oxide, min, % 20
Calcium and magnesium oxide, min, % 95 95
Silica, alumina, and oxide of iron, max, % 5 5
Carbon dioxide, max, %:
If sample is taken at place of manufacture 3 3
If sample is taken at any other place 10 10
5. Residue
5.1 The quicklime shall contain no more than 15 weight % of residue.residue as determined by the Test Methods C110 Slaking
Rate of Quicklime test procedure.
6. General Requirements
6.1 Quicklime shall be slaked and aged in accordance with the printed directions of the manufacturer. The resulting lime putty
shall be stored until cool.
6.2 Lime putty prepared in accordance with Appendix X1.4.2 must conform to the requirements of Specification C1489.
7. Sampling, Inspection, etc. and So Forth
7.1 The sampling, inspection, rejection, retesting, packaging, and marking shall be conducted in accordance with Methods
C50C50/C50M.
8. Test Methods
8.1 Conformance to chemical requirements shall be determined in accordance with Test Methods C25.
8.2 Conformance to residue requirements shall be determined i
...