iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2275-03

(Practice)

Standard Practice for Treestand Manufacturer Quality Assurance Program

Standard Practice for Treestand Manufacturer Quality Assurance Program

SIGNIFICANCE AND USE
The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality assurance program for treestands and elevated hunting equipment.
SCOPE
1.1 This practice provides minimum requirements for a quality assurance program.
1.2 The values stated are in inch-pound units and are to be regarded as standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-May-2003
ICS
65.145 - Hunting
Technical Committee
F08 - Sports Equipment, Playing Surfaces, and Facilities
Drafting Committee
F08.16 - Archery Products
Current Stage
Ref Project

Relations

Replaced By
ASTM F2275-08 - Standard Practice for Treestand Manufacturer Quality Assurance Program
Effective Date
01-Apr-2008
Referred By
ASTM F3249-20 - Standard Specification for Treestands, Climbing Sticks, and Tripod or Tower Stands
Effective Date
10-May-2003

Buy Standard

ASTM F2275-03 - Standard Practice for Treestand Manufacturer Quality Assurance ProgramASTM F2275-03 - Standard Practice for Treestand Manufacturer Quality Assurance Program
PreviousNext
Standard
ASTM F2275-03 - Standard Practice for Treestand Manufacturer Quality Assurance Program
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation:F2275–03
Standard Practice for
1
Treestand Manufacturer Quality Assurance Program
This standard is issued under the fixed designation F 2275; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope lated documents are utilized for each project. These drawings
and documents must be retained as long as the product remains
1.1 This practice provides minimum requirements for a
in production or distribution and for a period of five (5) years
quality assurance program.
after distribution ends.
1.2 The values stated are in inch-pound units and are to be
regarded as standard.
5. Material Control Procedures
1.3 This standard does not purport to address all of the
5.1 Aprocedureshallbeineffecttoensurethatallmaterials,
safety concerns, if any, associated with its use. It is the
processes and components, including raw materials, are in
responsibility of the user of this standard to establish appro-
accordance with the engineering specifications.
priate safety and health practices and determine the applica-
5.1.1 This procedure shall provide purchasing personnel
bility of regulatory limitations prior to use.
with all the information required to order appropriate material.
2. Referenced Documents 5.1.2 A receiving procedure shall be in effect so that
2
incoming material is checked against purchasing specifica-
2.1 ASTM Standards:
tions.
F 2120 Practice for Testing Treestand Load Capacity
5.1.3 Aprocedure shall be in effect so that material in stock
F 2121 Practice for Treestand Labels
can be properly identified for future use.
F 2122 Practice for Treestand Safety Devices
5.1.4 Documentation on any material, process, or compo-
F 2123 Practice for Treestand Instructions
nents certified shall be filed for reference.
F 2124 Practice for Testing Ladder Treestand, Tripod Tree-
stand and Climbing Stick Load Capacity
6. Inspection
F 2125 Test Method for Treestand Static Stability
6.1 A procedure shall be in effect so that appropriate
F 2126 Test Method for Treestand Static Load Capacity
inspections are made on manufactured parts and subassemblies
F 2127 Test Method for Treestand Adherence
to ensure conformance with engineering specifications.
F 2128 Test Method for Treestand Repetitive Load Capa-
6.2 A procedure shall be in effect so that appropriate
bility
inspections are made on purchased components.
3. Significance and Use 6.3 A procedure shall be in effect so completed units are
inspected prior to delivery.
3.1 The purpose of this practice is to provide the minimum
6.4 Nonconforming components shall be identified and
requirements necessary for the establishment of a written
evaluated for disposition as follows:
quality assurance program for treestands and elevated hunting
6.4.1 Reworked components shall be re-inspected in accor-
equipment.
dance with 5.1, 5.1.2,or 5.1.3 of this practice prior to use.
4. Drawing Control Procedure
6.4.2 A component not suitable for use shall be altered or
disposed of to avoid accidental use.
4.1 A procedure shall be in effect so that appropriate
6.4.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2337-22(Test Method)
Standard Test Method for Treestand Fall Arrest System

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F3544-21(Test Method)
Standard Test Method for Hunting Saddle Static Load Capacity

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of hunting saddles and bridge in terms of a factor of safety relative to the manufacturer’s rated capacity.  
1.2 The values shared are in inch-pound units and are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2275-21(Practice)
Standard Practice for Treestand Manufacturer Quality Assurance Program

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality assurance program for treestands and elevated hunting equipment.
SCOPE
1.1 This practice provides minimum requirements for a quality assurance program.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3412-20(Terminology)
Standard Terminology Relating to Treestands

SCOPE
1.1 This terminology covers terms related to treestands, climbing sticks, tripods or tower stands.  
1.2 This terminology is appropriate for use by treestand development professionals, owners and institutions, testing firms, users and other practitioners in matters concerning treestand test methods, practices and specifications which fall under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2337-22(Test Method)
Standard Test Method for Treestand Fall Arrest System

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F3544-21(Test Method)
Standard Test Method for Hunting Saddle Static Load Capacity

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of hunting saddles and bridge in terms of a factor of safety relative to the manufacturer’s rated capacity.  
1.2 The values shared are in inch-pound units and are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2275-21(Practice)
Standard Practice for Treestand Manufacturer Quality Assurance Program

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality assurance program for treestands and elevated hunting equipment.
SCOPE
1.1 This practice provides minimum requirements for a quality assurance program.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3412-20(Terminology)
Standard Terminology Relating to Treestands

SCOPE
1.1 This terminology covers terms related to treestands, climbing sticks, tripods or tower stands.  
1.2 This terminology is appropriate for use by treestand development professionals, owners and institutions, testing firms, users and other practitioners in matters concerning treestand test methods, practices and specifications which fall under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1210-23(Guide)
Standard Guide for Ecological Considerations for the Use of Oil Spill Dispersants in Freshwater and Other Inland Environments, Lakes and Large Water Bodies

SIGNIFICANCE AND USE
3.1 This guide is meant to aid response teams who may use it during spill response planning and spill events.  
3.2 This guide should be adapted to site specific circumstance.
SCOPE
1.1 This guide covers the use of oil spill dispersants to assist in the control of oil spills. The guide is written with the goal of minimizing the environmental impacts of oil spills; this goal is the basis on which the recommendations are made. Aesthetic and socioeconomic factors are not considered, although these and other factors are often important in spill response.  
1.2 Spill responders have available several means to control or clean up spilled oil. Chemical dispersants should be given equal consideration with other spill countermeasures.  
1.3 This is a general guide only. Oil, as used in this guide, includes crude oils and refined petroleum products. Differences between individual dispersants or between different oil products are not considered. The dispersibility of the oil with the chosen dispersant should be evaluated.  
1.4 The guide is organized by habitat type, for example, small ponds and lakes, rivers and streams, and land. It considers the use of dispersants primarily to protect habitats from impact (or to minimize impacts).  
1.5 This guide applies only to freshwater and other inland environments. It does not consider the direct application of dispersants to subsurface waters.  
1.6 In making dispersant use decisions, appropriate government authorities should be consulted as required by law.  
1.7 This guide does not address getting regulatory approval.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off