iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2275-21

(Practice)

Standard Practice for Treestand Manufacturer Quality Assurance Program

Standard Practice for Treestand Manufacturer Quality Assurance Program

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality assurance program for treestands and elevated hunting equipment.
SCOPE
1.1 This practice provides minimum requirements for a quality assurance program.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Apr-2021
ICS
65.145 - Hunting
Technical Committee
F08 - Sports Equipment, Playing Surfaces, and Facilities
Drafting Committee
F08.18 - Treestands
Current Stage
Ref Project

Relations

Refers
ASTM F3249-20 - Standard Specification for Treestands, Climbing Sticks, and Tripod or Tower Stands
Effective Date
01-Apr-2020

Buy Standard

ASTM F2275-21 - Standard Practice for Treestand Manufacturer Quality Assurance ProgramASTM F2275-21 - Standard Practice for Treestand Manufacturer Quality Assurance Program
PreviousNext
Standard
ASTM F2275-21 - Standard Practice for Treestand Manufacturer Quality Assurance Program
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM F2275-21 - Standard Practice for Treestand Manufacturer Quality Assurance ProgramREDLINE ASTM F2275-21 - Standard Practice for Treestand Manufacturer Quality Assurance Program
PreviousNext
Standard
REDLINE ASTM F2275-21 - Standard Practice for Treestand Manufacturer Quality Assurance Program
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F2275 − 21 An American National Standard
Standard Practice for
1
Treestand Manufacturer Quality Assurance Program
This standard is issued under the fixed designation F2275; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 4. Drawing Control Procedure
1.1 This practice provides minimum requirements for a 4.1 A procedure shall be in effect so that appropriate
quality assurance program. manufacturing drawings, their engineering revisions, and re-
lated documents are utilized for each project. These drawings
1.2 This standard does not purport to address all of the
and documents must be retained as long as the product remains
safety concerns, if any, associated with its use. It is the
in production or distribution and for a period of five (5) years
responsibility of the user of this standard to establish appro-
after distribution ends.
priate safety, health, and environmental practices and deter-
mine the applicability of regulatory limitations prior to use.
5. Material Control Procedures
1.3 This international standard was developed in accor-
5.1 Aprocedureshallbeineffecttoensurethatallmaterials,
dance with internationally recognized principles on standard-
processes and components, including raw materials, are in
ization established in the Decision on Principles for the
accordance with the engineering specifications.
Development of International Standards, Guides and Recom-
5.1.1 This procedure shall provide purchasing personnel
mendations issued by the World Trade Organization Technical
with all the information required to order appropriate material.
Barriers to Trade (TBT) Committee.
5.1.2 A receiving procedure shall be in effect so that
incoming material is checked against purchasing specifica-
2. Referenced Documents
tions.
2
2.1 ASTM Standards:
5.1.3 Aprocedure shall be in effect so that material in stock
F2123 Practice for Treestand Instructions
can be properly identified for future use.
F2125 Test Method for Treestand Static Stability andAdher-
5.1.4 Documentation on any material, process, or compo-
ence
nents certified shall be filed for reference.
F2126 Test Method for Treestand Static Load Capacity
5.2 A procedure will be in effect to ensure that the final
F2128 Test Method for Treestand Repetitive Loading Capa-
assembly of each product has a permanent date code indicating
bility
its date of manufacture.
F2337 Test Method for Treestand Fall Arrest System
5.2.1 A date code shall be located on each final product
F2531 Test Method for Load Capacity of Treestand Seats
assembly.
F3249 Specification for Treestands, Climbing Sticks, and
5.2.2 Thedatecodeshallincludeasaminimumthelastdigit
Tripod or Tower Stands
of the year and a code for the month or the week. (Example: for
March, 2009 – “39” or “C9” or “93” or “9C”.) Any code that
3. Significance and Use
is logical, consistent and able to be decoded by the manufac-
3.1 The purpose of this practice is to provide the minimum
turer is acceptable. Any product in production for ten years or
requirements necessary for the establishment of a written
more with no changes will be required to add a third number so
quality assurance program for treestands and elevated hunting
that the last two digits of the year are known.
equipment.
5.2.3 Date codes shall be made permanent.
6. Inspection
1
This practice is under the jurisdiction of ASTM Committee F08 on Sports
6.1 A procedure shall be in effect so that appropriate
Equipment, Playing Surfaces, and Facilities and is the direct responsibility of
inspections are made on manufactured parts and subassemblies
Subcommittee F08.18 on Treestands.
Current edition approved May 1, 2021. Published May 2021. Originally to ensure conformance with engineering specifications.
approved in 2003. Last previous edition approved in 2017 as F2275 – 17. DOI:
6.2 A procedure shall be in effect so that appropriate
10.1520/F2275-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or inspections are made on purchased components.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.3 A procedure shall be in effect so completed units are
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. inspected prior to delivery.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ------------------
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2275 − 17 F2275 − 21 An American National Standard
Standard Practice for
1
Treestand Manufacturer Quality Assurance Program
This standard is issued under the fixed designation F2275; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice provides minimum requirements for a quality assurance program.
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
3
F2120 Practice for Testing Treestand Load Capacity (Withdrawn 2019)
3
F2121 Practice for Treestand Labels (Withdrawn 2017)
3
F2122 Practice for Treestand Safety Devices (Withdrawn 2017)
F2123 Practice for Treestand Instructions
3
F2124 Practice for Testing Treestand Ladder, Tripod Stand and Climbing Stick Load Capacity (Withdrawn 2017)
F2125 Test Method for Treestand Static Stability and Adherence
F2126 Test Method for Treestand Static Load Capacity
F2128 Test Method for Treestand Repetitive Loading Capability
F2337 Test Method for Treestand Fall Arrest System
F2531 Test Method for Load Capacity of Treestand Seats
F3249 Specification for Treestands, Climbing Sticks, and Tripod or Tower Stands
3. Significance and Use
3.1 The purpose of this practice is to provide the minimum requirements necessary for the establishment of a written quality
assurance program for treestands and elevated hunting equipment.
4. Drawing Control Procedure
4.1 A procedure shall be in effect so that appropriate manufacturing drawings, their engineering revisions, and related documents
1
This practice is under the jurisdiction of ASTM Committee F08 on Sports Equipment, Playing Surfaces, and Facilities and is the direct responsibility of Subcommittee
F08.18 on Treestands.
Current edition approved Dec. 1, 2017May 1, 2021. Published January 2018May 2021. Originally approved in 2003. Last previous edition approved in 20142017 as
F2275 – 10 (2014).F2275 – 17. DOI: 10.1520/F2275-17.10.1520/F2275-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2275 − 21
are utilized for each project. These drawings and documents must be retained as long as the product remains in production or
distribution and for a period of five (5) years after distribution ends.
5. Material Control Procedures
5.1 A procedure shall be in effect to ensure that all materials, processes and components, including raw materials, are in
accordance with the engineering specifications.
5.1.1 This procedure shall provide purchasing personnel with all the information required to order appropriate material.
5.1.2 A receiving procedure shall be in effect so that incoming material is checked against purchasing specifications.
5.1.3 A procedure shall be in effect so that material in stock can be properly identified for future use.
5.1.4 Documentation on any material, process, or components certified shall be filed for reference.
5.2 A procedure will be in effect to ensure that the final assembly of each product has a permanent date code indicating its date
of manufacture.
5.2.1 A date code shall be located on each final product assembly.
5.2.2 The date code shall include as a minimum the last digit of the year and a code for the month or the week. (Example: for
March, 2009 – “39” or “C9” or “93” or “9C”.) Any code that is logical, consistent and able to be decoded by the manufacturer
is acceptable. Any product in production for ten years or more with no c
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2337-22(Test Method)
Standard Test Method for Treestand Fall Arrest System

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F3544-21(Test Method)
Standard Test Method for Hunting Saddle Static Load Capacity

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of hunting saddles and bridge in terms of a factor of safety relative to the manufacturer’s rated capacity.  
1.2 The values shared are in inch-pound units and are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3412-20(Terminology)
Standard Terminology Relating to Treestands

SCOPE
1.1 This terminology covers terms related to treestands, climbing sticks, tripods or tower stands.  
1.2 This terminology is appropriate for use by treestand development professionals, owners and institutions, testing firms, users and other practitioners in matters concerning treestand test methods, practices and specifications which fall under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2337-22(Test Method)
Standard Test Method for Treestand Fall Arrest System

SIGNIFICANCE AND USE
4.1 This test method is intended to measure the maximum arrest force and dynamic strength on treestand FAS and components or subsystems. This test is intended for program quality assurance and production quality control purposes. It is not intended to be an independent material or product acceptance test.
SCOPE
1.1 This test method covers the determination of the load capacities for treestand fall arrest systems (FAS) and components or subsystems.  
1.2 This test method addresses equipment used in hunting situations requiring personal protection against falls from heights and applies to the manufacturers, distributors, purchasers, and users of such equipment.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM F3544-21(Test Method)
Standard Test Method for Hunting Saddle Static Load Capacity

SIGNIFICANCE AND USE
5.1 This test method is intended for quality assurance and production control purposes.
SCOPE
1.1 This test method covers the determination of the static load capacity of hunting saddles and bridge in terms of a factor of safety relative to the manufacturer’s rated capacity.  
1.2 The values shared are in inch-pound units and are to be regarded as the standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3412-20(Terminology)
Standard Terminology Relating to Treestands

SCOPE
1.1 This terminology covers terms related to treestands, climbing sticks, tripods or tower stands.  
1.2 This terminology is appropriate for use by treestand development professionals, owners and institutions, testing firms, users and other practitioners in matters concerning treestand test methods, practices and specifications which fall under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM A370-23(Test Method)
Standard Test Methods and Definitions for Mechanical Testing of Steel Products

SIGNIFICANCE AND USE
4.1 The primary use of these test methods is testing to determine the specified mechanical properties of steel, stainless steel, and related alloy products for the evaluation of conformance of such products to a material specification under the jurisdiction of ASTM Committee A01 and its subcommittees as designated by a purchaser in a purchase order or contract.  
4.1.1 These test methods may be and are used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing.  
4.1.2 The material condition at the time of testing, sampling frequency, specimen location and orientation, reporting requirements, and other test parameters are contained in the pertinent material specification or in a general requirement specification for the particular product form.  
4.1.3 Some material specifications require the use of additional test methods not described herein; in such cases, the required test method is described in that material specification or by reference to another appropriate test method standard.  
4.2 These test methods are also suitable to be used for testing of steel, stainless steel and related alloy materials for other purposes, such as incoming material acceptance testing by the purchaser or evaluation of components after service exposure.  
4.2.1 As with any mechanical testing, deviations from either specification limits or expected as-manufactured properties can occur for valid reasons besides deficiency of the original as-fabricated product. These reasons include, but are not limited to: subsequent service degradation from environmental exposure (for example, temperature, corrosion); static or cyclic service stress effects, mechanically-induced damage, material inhomogeneity, anisotropic structure, natural aging of select alloys, further processing not included in the specification, sampling limitations, and measuring equipment calibration uncertainty. There is statistical variation in all aspects of mechanical testin...
SCOPE
1.1 These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.  
1.2 The following mechanical tests are described:    
Sections  
Tension  
7 to 14  
Bend  
15  
Hardness  
16  
Brinell  
17  
Rockwell  
18  
Portable  
19  
Impact  
20 to 30  
Keywords  
32  
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:    
Annex  
Bar Products  
Annex A1  
Tubular Products  
Annex A2  
Fasteners  
Annex A3  
Round Wire Products  
Annex A4  
Significance of Notched-Bar Impact Testing  
Annex A5  
Converting Percentage Elongation of Round Specimens to
Equivalents for Flat Specimens  
Annex A6    
Testing Multi-Wire Strand  
Annex A7  
Rounding of Test Data  
Annex A8  
Methods for Testing Steel Reinforcing Bars  
Annex A9  
Procedure for Use and Control of Heat-cycle Simulation  
Annex A10  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 When these test methods are referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 in. or 8 in. may be report...

  • Standard
    51 pages
    English language
    sale 15% off
  • Standard
    51 pages
    English language
    sale 15% off
ASTM
ASTM F3565-23(Practice)
Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service

SIGNIFICANCE AND USE
4.1 Using the procedures and apparatus in Sections 8 and 9 and the manufacturer's instructions, pressure-tight joints as strong as the pipe itself can be made between manufacturer-recommended combinations of pipe and fittings. See Specification F1055 for performance requirements of polyethylene electrofusion fittings.
SCOPE
1.1 This practice describes procedures for making joints suitable for pressure service with polyethylene (PE) pipe and fittings by means of electrofusion joining techniques in, but not limited to, a field environment. Other suitable electrofusion joining procedures are available from various sources including fitting manufacturers. This standard does not purport to address all possible electrofusion joining procedures, or to preclude the use of qualified procedures developed by other parties that have been proven to produce reliable electrofusion joints. (Note 1)
Note 1: Reference to the manufacturer in this practice refers to the electrofusion fitting manufacturer.  
1.2 The parameters and procedure are applicable only to joining polyethylene pipe and fittings (Note 2) which are intended for PE fuel gas pipe per Specification D2513 and PE potable water, sewer and industrial pipe manufactured per Specification F714, Specification D3035, Specification F2619, and AWWA C901 and C906.
Note 2: Commercially available materials classified with a thermoplastic pipe material designation code beginning with PE 14, PE 23, PE 24, PE 27, PE 33, PE 34, PE 36, and PE 46, and PE 47 in accordance with Specification D3350 and Terminology F412 are generally acceptable for electrofusion joining using this practice. Consult with the pipe or fitting manufacturer for specific compatibility information.  
1.3 Parts that are within the dimensional tolerances given in present ASTM specifications are required to produce sound joints between polyethylene pipe and fittings when using the joining techniques described in this practice.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 The text of this practice references notes, footnotes, and appendices which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the practice.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D5141-23(Test Method)
Standard Test Method for Determining Filtering Efficiency and Flow Rate of the Filtration Component of a Sediment Retention Device

SIGNIFICANCE AND USE
5.1 This test method is used to determine the filtering efficiency and flow rate of the filtration component of a sediment retention device, such as a silt fence, a silt barrier, or a silt curtain, for specific soil tested.  
5.2 This test method may be used for the design of the filtration component of a sediment retention device to meet requirements of regulatory agencies in filtering efficiency or flow rate for the specific soil tested.  
5.2.1 The designer can use this test method to determine the spacing between sediment retention devices.  
5.3 This test method is intended for performance evaluation, as the results will depend on the specific soil evaluated. Unless testing with the default soil is desired, it is recommended that the user or representative perform the test to pre-approve products, as sediment retention device manufacturers are not typically equipped to handle or test soil requirements.  
5.4 This test method provides a means of evaluating the filtration component of sediment retention devices with different soils under various conditions that simulate the conditions that exist in a sediment retention device installation. This test method may be used to simulate several storm events on the same sediment retention device specimen. Therefore, the number of times this test is repeated per specimen is dependent upon the user and the site conditions.
SCOPE
1.1 This test method is used to determine the filtering efficiency and the flow rate of the filtration component of a sediment retention device, such as a silt fence, silt barrier, or inlet protector.  
1.1.1 The results are shown as a percentage for filtering efficiency and cubic metres per square metre per minute (m3/m2/min) or gallons per square foot per minute (gal/ft2/min) for flow rate.  
1.1.2 The filtering efficiency indicates the percent of sediment removed from sediment-laden water.  
1.1.3 The flow rate is the average rate of passage of the sediment-laden water through the filtration component of a sediment retention device.  
1.2 This test method requires several specialized pieces of equipment, such as an integrated water sampler and an analytical balance, or a vacuum filtration system. At the client’s discretion, the test soil is either a site-specific soil or a soil that is representative of a target default gradation.  
1.3 The values stated in SI units are the standard, while the inch-pound units are provided for information. The values expressed in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values in any way.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F2647-07(2023)(Guide)
Standard Guide for Approved Methods of Installing a CVS (Central Vacuum System)

SIGNIFICANCE AND USE
4.1 The suggestions of this guide are intended to provide proper installation materials and practices to be used during the installation of a central-vacuum system.
SCOPE
1.1 This guide demonstrates proper methods for installing a central-vacuum system.  
1.2 Appendix X1 contains additional sources of information that may be helpful to the user of this guide.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off