ASTM F1347-91(2018)

Standard Specification for Manually Operated Fueling Hose Reels

ABSTRACT
This specification covers manually operated fueling hose reels for use with collapsible and noncollapsible hose. Fueling hose reels shall be of one of the following types as specified: type 1, type 2, type 3, and type 4. The hose reel shall be of a durable, rigid construction, as light in weight and compact as practicable. The reel drum may have either smoothly formed flat sides or suitable spoke ribs, so formed as not to damage the hose. Reels shall be provided with a holding brake to lock the reel in any position. The reel shall be fitted with a device for clamping the hose nozzle securely to the reel to prevent unwinding of the hose and damage to the nozzle. The reel hub discharge shall be angled to provide a smooth tangential contact of the hose with the reel drum. The reel shall have an aromatic fuels tight rotating joint between reel inlet connection and the rotating hub on the reel drum. The reel inlet connection shall be flanged, the flange being part of the rotating swivel joint. Hydrostatic tset and operating test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers manually operated fueling hose reels for use with collapsible and noncollapsible hose.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the test methods portion, Section 12 of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 30-Sep-2018
• ICS: 23.040.70 - Hoses and hose assemblies
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.07 - General Requirements

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1347 − 91 (Reapproved 2018) An American National Standard
Standard Specification for
1
Manually Operated Fueling Hose Reels
This standard is issued under the fixed designation F1347; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope MIL-T-16366 Terminals, Electric Lug and Conductor
Splices, Crimp Style
1.1 This specification covers manually operated fueling
MIL-H-17902 Hose, End Fittings and Hose Assemblies,
hose reels for use with collapsible and noncollapsible hose.
Synthetic Rubber, Aircraft Fuels
1.2 The values stated in inch-pound units are to be regarded
MIL-F-20042 Flanges, Pipe and Bulkhead, Bronze (Silver
as standard. The values given in parentheses are mathematical
Brazing)
conversions to SI units that are provided for information only
MIL-P-24441 Epoxy-Polyamide Primer
and are not considered standard. 3
2.3 Military Standard:
1.3 The following precautionary caveat pertains only to the MIL-STD-130 Identification Marking of U.S. Military Prop-
test methods portion, Section 12 of this specification: This
erty
standard does not purport to address all of the safety concerns,
3. Classification
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety, health, and
3.1 Fueling hose reels shall be of one of the following types
environmental practices and determine the applicability of
as specified:
1
regulatory limitations prior to use.
3.1.1 Type 1—For 150 ft (46 m) of collapsible 2 ⁄2-in.
1.4 This international standard was developed in accor-
(65-mm) hose.
1
dance with internationally recognized principles on standard-
3.1.2 Type 2—For 150 ft (46 m) of noncollapsible 1 ⁄2-in.
ization established in the Decision on Principles for the
(38-mm) hose or 100 ft (30 m) of noncollapsible 2-in. (50-mm)
Development of International Standards, Guides and Recom-
hose.
1
mendations issued by the World Trade Organization Technical
3.1.3 Type 3—For 150 ft (46 m) of noncollapsible 1 ⁄2-in.
1
Barriers to Trade (TBT) Committee.
(38-mm) hose or for 150 ft (46 m) of collapsible 2 ⁄2-in.
(65-mm) hose.
2. Referenced Documents
3.1.4 Type 4—Capacity as specified by purchaser.
2
2.1 ASTM Standards:
4. Ordering Information
B148 Specification for Aluminum-Bronze Sand Castings
4.1 Orders for material under this specification shall include
D3006 Specification for Polyethylene Plastic Pressure-
the following information:
Sensitive Electrical Insulating Tape
4.1.1 Title, number, and year of issue of this specification,
D3951 Practice for Commercial Packaging
3 4.1.2 Type of hose reel including hose size and type (see
2.2 Military Specifications:
3.1), (length of hose for Type 4),
MIL-S-901 Shock Test, H.I. (High-Impact); Shipboard
4.1.3 Whether right- or left-hand reels are required (see 6.5),
Machinery, Equipment and Systems, Requirements for
4.1.4 Flange inlet thickness and bolt hole dimensions (see
6.7),
4.1.5 Drawings required (see 9.1),
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
4.1.6 The number of samples to be inspected and tested (see
and Marine Technology and is the direct responsibility of Subcommittee F25.07 on
General Requirements. 11.2),
Current edition approved Oct. 1, 2018. Published October 2018. Originally
4.1.7 Certification, if required (see 15.1),
approved in 1991. Last previous edition approved in 2012 as F1347 – 91 (2012).
4.1.8 Test report, if required (see 15.1), and
DOI: 10.1520/F1347-91R18.
2
4.1.9 Applicability of supplementary requirements.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on 5. Materials and Manufacture
the ASTM website.
3 5.1 Except as otherwise specified herein, the hose reels shall
Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,
Philadelphia, PA 19111-5094, http://quicksearch.dla.mil. be constructed of aluminum, aluminum bronze, or other
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1347 − 91 (2018)
suitable nonsparking materials. All fittings conveying aromatic surfaces, and all such parts shall be lubricated before delivery
fuels through the hose reel shall be made of aluminum bronze with a lubricant soluble in aromatic fuels. Bearing seals shall
in acc
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1347 − 91 (Reapproved 2012) F1347 − 91 (Reapproved 2018)An American National Standard
Standard Specification for
1
Manually Operated Fueling Hose Reels
This standard is issued under the fixed designation F1347; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers manually operated fueling hose reels for use with collapsible and noncollapsible hose.
1.2 The values stated in inch-pound units are to be regarded as standard. The SI units values given in parentheses are for
information only.mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 12 of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of
regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
B148 Specification for Aluminum-Bronze Sand Castings
D3006 Specification for Polyethylene Plastic Pressure-Sensitive Electrical Insulating Tape
D3951 Practice for Commercial Packaging
3
2.2 Military Specifications:
MIL-S-901 Shock Test, H.I. (High-Impact); Shipboard Machinery, Equipment and Systems, Requirements for
MIL-T-16366 Terminals, Electric Lug and Conductor Splices, Crimp Style
MIL-H-17902 Hose, End Fittings and Hose Assemblies, Synthetic Rubber, Aircraft Fuels
MIL-F-20042 Flanges, Pipe and Bulkhead, Bronze (Silver Brazing)
MIL-P-24441 Epoxy-Polyamide Primer
3
2.3 Military Standard:
MIL-STD-130 Identification Marking of U.S. Military Property
3. Classification
3.1 Fueling hose reels shall be of one of the following types as specified:
1
3.1.1 Type 1—For 150 ft (46 m) of collapsible 2 ⁄2-in. (65-mm) hose.
1
3.1.2 Type 2—For 150 ft (46 m) of noncollapsible 1 ⁄2-in. (38-mm) hose or 100 ft (30 m) of noncollapsible 2-in. (50-mm) hose.
1 1
3.1.3 Type 3—For 150 ft (46 m) of noncollapsible 1 ⁄2-in. (38-mm) hose or for 150 ft (46 m) of collapsible 2 ⁄2-in. (65-mm) hose.
3.1.4 Type 4—Capacity as specified by purchaser.
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.07 on General
Requirements.
Current edition approved May 1, 2012Oct. 1, 2018. Published May 2012October 2018. Originally approved in 1991. Last previous edition approved in 20062012 as
F1347 – 91 (2006).(2012). DOI: 10.1520/F1347-91R12.10.1520/F1347-91R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA
19111-5098, http://dodssp.daps.dla.mil.19111-5094, http://quicksearch.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1347 − 91 (2018)
4. Ordering Information
4.1 Orders for material under this specification shall include the following information:
4.1.1 Title, number, and year of issue of this specification,
4.1.2 Type of hose reel including hose size and type (see 3.1), (length of hose for Type 4),
4.1.3 Whether right- or left-hand reels are required (see 6.5),
4.1.4 Flange inlet thickness and bolt hole dimensions (see 6.7),
4.1.5 Drawings required (see 9.1),
4.1.6 The number of samples to be inspected and tested (see 11.2),
4.1.7 Certification, if required (see 15.1),
4.1.8 Test report, if r
...