ASTM E135-22

Standard Terminology Relating to Analytical Chemistry for Metals, Ores, and Related Materials

SIGNIFICANCE AND USE
3.1 Definitions given in Section 4 are intended for use in all standards on analytical chemistry for metals, ores, and related materials. The definitions should be used uniformly and consistently. The purpose of this terminology is to promote clear understanding and interpretation of the standards in which definitions are used.
SCOPE
1.1 This is a compilation of terms commonly used in analytical chemistry for metals, ores, and related materials. Terms that are generally understood or defined adequately in other readily available sources are either not included or their sources are identified.  
1.2 A definition is a single sentence with additional information included in a discussion.  
1.3 Definitions identical to those published by another standards organization or ASTM committee are identified with the name of the organization or the identifying document and ASTM committee.  
1.4 Definitions specific to a particular field (such as emission spectrometry) are identified with an italicized introductory phrase.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Aug-2022
• ICS: 01.040.71 - Chemical technology (Vocabularies)
• ICS: 71.040.50 - Physicochemical methods of analysis
• Technical Committee: E01 - Analytical Chemistry for Metals, Ores, and Related Materials
• Drafting Committee: E01.23 - Terminology and Editorial

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E135 − 22
Standard Terminology Relating to
Analytical Chemistry for Metals, Ores, and Related
1
Materials
This standard is issued under the fixed designation E135; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E2438 Practice for Implementing Standard Performance
Based Test Methods for theAnalysis of Metals, Ores, and
1.1 This is a compilation of terms commonly used in
3
Related Materials (Withdrawn 2014)
analytical chemistry for metals, ores, and related materials.
4
2.2 ISO Standard:
Terms that are generally understood or defined adequately in
ISO Guide 30 Terms and Definitions Used in Connection
other readily available sources are either not included or their
with Reference Materials
sources are identified.
3. Significance and Use
1.2 A definition is a single sentence with additional infor-
mation included in a discussion.
3.1 Definitions given in Section 4 are intended for use in all
standards on analytical chemistry for metals, ores, and related
1.3 Definitions identical to those published by another
materials. The definitions should be used uniformly and
standards organization orASTM committee are identified with
consistently. The purpose of this terminology is to promote
the name of the organization or the identifying document and
clear understanding and interpretation of the standards in
ASTM committee.
which definitions are used.
1.4 Definitions specific to a particular field (such as emis-
sion spectrometry) are identified with an italicized introductory 4. Terminology Definitions
phrase.
aim total intralaboratory uncertainty, n—the maximum
1.5 This international standard was developed in accor-
deviation (95 % confidence) to be allowed in the design of
dance with internationally recognized principles on standard-
the total intralaboratory uncertainty of a test method, begin-
ization established in the Decision on Principles for the
ning with the preparation of a homogeneous sample and
Development of International Standards, Guides and Recom-
ending with a final report value to the client.
mendations issued by the World Trade Organization Technical
analytical curve—see calibration curve.
Barriers to Trade (TBT) Committee.
analyte, n—in methods of chemical analysis, the constituent
2. Referenced Documents
determined by a chemical measurement process (Sept. 1,
2
2022).
2.1 ASTM Standards:
E1914 Practice for Use of Terms Relating to the Develop-
analytical gap, n—in atomic emission spectrometry,theregion
ment and Evaluation of Methods for Chemical Analysis
betweentwoelectrodesinwhichthespecimenisexcitedand
3
(Withdrawn 2016)
from which radiant energy is used for analysis (Aug. 1,
E2437 Practice for Designing and Validating Performance-
2020).
Based Test Methods for theAnalysis of Metals, Ores, and
3
analytical line, n—in atomic spectrometry, the particular
Related Materials (Withdrawn 2014)
wavelengthofelectromagneticradiationusedindetermining
the presence or concentration of an element.
1
This terminology is under the jurisdiction of ASTM Committee E01 on
arc, condensed—see discharge, triggered capacitor.
Analytical Chemistry for Metals, Ores, and Related Materials and is the direct
responsibility of Subcommittee E01.23 on Terminology and Editorial.
noncapacitive ac arc, n—in atomic emission spectrometry,a
Current edition approved Sept. 1, 2022. Published December 2022. Originally
series of separate electrical discharges, individually self-
approved in 1958. Last previous edition approved in 2021 as E135 – 21a. DOI:
initiating or initiated separately by another means, in which
10.1520/E0135-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
each current pulse has a polarity that is reversed from the
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
previous one.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
4
The last approved version of this historical standard is referenced on Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
www.astm.org. 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E135 − 22
arc line—not recommended; see atom line. given measurement procedure, that can be distinguished
from the background signal at a specified confidence level.
atom line, n—in atomic emission spectrometry, a spectral line
E1914
resulting from radiation emitted during electron transition as
D
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: E135 − 21a E135 − 22
Standard Terminology Relating to
Analytical Chemistry for Metals, Ores, and Related
1
Materials
This standard is issued under the fixed designation E135; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This is a compilation of terms commonly used in analytical chemistry for metals, ores, and related materials. Terms that are
generally understood or defined adequately in other readily available sources are either not included or their sources are identified.
1.2 A definition is a single sentence with additional information included in a discussion.
1.3 Definitions identical to those published by another standards organization or ASTM committee are identified with the name
of the organization or the identifying document and ASTM committee.
1.4 Definitions specific to a particular field (such as emission spectrometry) are identified with an italicized introductory phrase.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E1914 Practice for Use of Terms Relating to the Development and Evaluation of Methods for Chemical Analysis (Withdrawn
3
2016)
E2437 Practice for Designing and Validating Performance-Based Test Methods for the Analysis of Metals, Ores, and Related
3
Materials (Withdrawn 2014)
E2438 Practice for Implementing Standard Performance Based Test Methods for the Analysis of Metals, Ores, and Related
3
Materials (Withdrawn 2014)
4
2.2 ISO Standard:
ISO Guide 30 Terms and Definitions Used in Connection with Reference Materials
3. Significance and Use
3.1 Definitions given in Section 4 are intended for use in all standards on analytical chemistry for metals, ores, and related
1
This terminology is under the jurisdiction of ASTM Committee E01 on Analytical Chemistry for Metals, Ores, and Related Materials and is the direct responsibility of
Subcommittee E01.23 on Terminology and Editorial.
Current edition approved June 1, 2021Sept. 1, 2022. Published July 2021December 2022. Originally approved in 1958. Last previous edition approved in 2021 as
E135 – 21.E135 – 21a. DOI: 10.1520/E0135-21A.10.1520/E0135-22.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
E135 − 22
materials. The definitions should be used uniformly and consistently. The purpose of this terminology is to promote clear
understanding and interpretation of the standards in which definitions are used.
4. Terminology Definitions
aim total intralaboratory uncertainty, n—the maximum deviation (95 % confidence) to be allowed in the design of the total
intralaboratory uncertainty of a test method, beginning with the preparation of a homogeneous sample and ending with a final
report value to the client.
analytical curve—see calibration curve.
analyte, n—in methods of chemical analysis, the constituent determined by a chemical measurement process.process (Sept. 1,
2022). E1914
analytical gap, n—in atomic emission spectrometry, the region between two electrodes in which the specimen is excited and
from which radiant energy is used for analysis (Aug. 1, 2020).
analytical line, n—in atomic spectrometry, the particular wavelength of electromagnetic radiation used in determining the
presence or concentration of an element.
arc, condensed—see discharge, triggered capacitor.
noncapacitive ac arc,n—in atomic emission spectrometry, a series of separate electrical discharges, individually self-initiating
or initiated separately by another means, in which ea
...