ASTM A36/A36M-01

Standard Specification for Carbon Structural Steel

SCOPE
1.1 This specification covers carbon steel shapes, plates, and bars of structural quality for use in riveted, bolted, or welded construction of bridges and buildings, and for general structural purposes.
1.2 Supplementary requirements are provided for use where additional testing or additional restrictions are required by the purchaser. Such requirements apply only when specified in the purchase order.
1.3 When the steel is to be welded, a welding procedure suitable for the grade of steel and intended use or service is to be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.
1.4 For Group 4 and 5 wide flange shapes for use in tension, it is recommended that the purchaser consider specifying supplementary requirements, such as fine austenitic grain size and Charpy V-notch impact testing.
1.5 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system is to be used independently of the other, without combining values in any way.
1.6 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.
1.7 For plates cut from coiled product, the additional requirements, including additional testing requirements and the reporting of additional test results, of A6/A6M apply.

General Information

• Status: Historical
• Publication Date: 09-Sep-2001
• ICS: 77.140.10 - Heat-treatable steels
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.02 - Structural Steel for Bridges, Buildings, Rolling Stock and Ships

Relations

• Replaces: ASTM A36/A36M-00a - Standard Specification for Carbon Structural Steel
• Effective Date: 10-Sep-2001
• Replaced By: ASTM A36/A36M-02 - Standard Specification for Carbon Structural Steel
• Effective Date: 10-Dec-2002
• Referred By: ASTM C361M-22 - Standard Specification for Reinforced Concrete Low-Head Pressure Pipe (Metric)
• Effective Date: 10-Sep-2001
• Referred By: ASTM F1602-12(2023) - Standard Specification for Kettles, Steam-Jacketed, 20 to 200 gal (75.7 to 757 L), Floor or Wall Mounted, Direct Steam, Gas and Electric Heated
• Effective Date: 10-Sep-2001
• Referred By: ASTM D5367-16(2021) - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted
• Effective Date: 10-Sep-2001
• Referred By: ASTM D7230-06(2021) - Standard Guide for Evaluating Polymeric Lining Systems for Water Immersion in Coating Service Level III Safety-Related Applications on Metal Substrates
• Effective Date: 10-Sep-2001
• Referred By: ASTM F1965-17(2022) - Standard Test Method for Performance of Deck Ovens
• Effective Date: 10-Sep-2001
• Referred By: ASTM F3459-21 - Standard Specification for Rigid Poly Vinyl Chloride (PVC) Exterior Profiles Used for Sound Walls
• Effective Date: 10-Sep-2001
• Referred By: ASTM F1495-20 - Standard Specification for Combination Oven Electric or Gas Fired
• Effective Date: 10-Sep-2001
• Referred By: ASTM A1075-12(2022) - Standard Specification for Flanged Steel U-Channel Posts
• Effective Date: 10-Sep-2001
• Referred By: ASTM F1143-19 - Standard Specification for Manhole Cover Assembly, Bolted, Raised, Oiltight and Watertight
• Effective Date: 10-Sep-2001
• Referred By: ASTM G92-20 - Standard Practice for Characterization of Atmospheric Test Sites
• Effective Date: 10-Sep-2001
• Referred By: ASTM F670-02(2022) - Standard Specification for Tanks, 5 and 10-Gal (20 and 40-L) Lube Oil Dispensing
• Effective Date: 10-Sep-2001
• Referred By: ASTM F1385-07(2023) - Standard Practice for Platforms in Cargo Tanks
• Effective Date: 10-Sep-2001
• Referred By: ASTM F1069-19 - Standard Specification for Doors, Watertight, Gastight/Airtight and Weathertight, Individually Dogged, for Marine Use
• Effective Date: 10-Sep-2001

Standards Content (Sample)

NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: A 36/A 36M – 01
Standard Specification for
1
Carbon Structural Steel
This standard is issued under the fixed designation A 36/A 36M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope Rolled Structural Steel Bars, Plates, Shapes, and Sheet
3
2 Piling
1.1 This specification covers carbon steel shapes, plates,
A 27/A 27M Specification for Steel Castings, Carbon, for
and bars of structural quality for use in riveted, bolted, or
4
General Application
welded construction of bridges and buildings, and for general
A 307 Specification for Carbon Steel Bolts and Studs,
structural purposes.
5
60 000 psi Tensile Strength
1.2 Supplementary requirements are provided for use where
A 325 Specification for High-Strength Bolts for Structural
additional testing or additional restrictions are required by the
5
Steel Joints
purchaser. Such requirements apply only when specified in the
A 325M Specification for High-Strength Bolts for Struc-
purchase order.
5
tural Steel Joints [Metric]
1.3 When the steel is to be welded, a welding procedure
A 500 Specification for Cold-Formed Welded and Seamless
suitable for the grade of steel and intended use or service is to
6
Carbon Steel Structural Tubing in Rounds and Shapes
be utilized. See Appendix X3 of Specification A 6/A 6M for
A 501 Specification for Hot-Formed Welded and Seamless
information on weldability.
6
Carbon Steel Structural Tubing
1.4 For Group 4 and 5 wide flange shapes for use in tension,
5
A 502 Specification for Steel Structural Rivets
it is recommended that the purchaser consider specifying
5
A 563 Specification for Carbon and Alloy Steel Nuts
supplementary requirements, such as fine austenitic grain size
A 563M Specification for Carbon and Alloy Steel Nuts
and Charpy V-notch impact testing.
5
[Metric]
1.5 The values stated in either inch-pound units or SI units
A 570/A 570M Specification for Steel, Sheet and Strip,
are to be regarded separately as standard. Within the text, the
7
Carbon, Hot-Rolled, Structural Quality
SI units are shown in brackets. The values stated in each
A 668/A 668M Specification for Steel Forgings, Carbon
system are not exact equivalents; therefore, each system is to
8
and Alloy, for General Industrial Use
be used independently of the other, without combining values
F 568M Specification for Carbon and Alloy Steel Externally
in any way.
5
Threaded Metric Fasteners
1.6 The text of this specification contains notes or footnotes,
or both, that provide explanatory material. Such notes and
3. Appurtenant Materials
footnotes, excluding those in tables and figures, do not contain
3.1 When components of a steel structure are identified with
any mandatory requirements.
this ASTM designation but the product form is not listed in the
1.7 For structural products cut from coiled product, the
scope of this specification, the material shall conform to one of
additional requirements, including additional testing require-
the standards listed in Table 1 unless otherwise specified by the
ments and the reporting of additional test results, of A 6/A 6M
purchaser.
apply.
4. General Requirements for Delivery
2. Referenced Documents
4.1 Material furnished under this specification shall con-
2.1 ASTM Standards:
form to the requirements of the current edition of Specification
A 6/A 6M Specification for General Requirements for
A 6/A 6M, for the ordered material, unless a conflict exists in
which case this specification shall prevail.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
3
Stainless Steel, and Related Alloys, and is the direct responsibility of Subcommittee Annual Book of ASTM Standards, Vol 01.04.
4
A01.02 on Structural Steel for Bridges, Buildings, Rolling Stock, and Ships. Annual Book of ASTM Standards, Vol 01.02.
5
Current edition approved Sept. 10, 2001. Published September 2001. Originally Annual Book of ASTM Standards, Vol 15.08.
6
published as A 36 – 60 T. Last previous edition A 36/A 36M – 00a. Annual Book of ASTM Standards, Vol 01.01.
2 7
For ASME Boiler and Pressure Vessel Code Applications, see related Specifi- Annual Book of ASTM Standards, Vol 01.03.
8
cations SA-36 in Section II of that Code. Annual Book of ASTM Standards, Vol 01.05.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (w
...