ASTM F1069-19

Standard Specification for Doors, Watertight, Gastight/Airtight and Weathertight, Individually Dogged, for Marine Use

ABSTRACT
This specification covers the principal shapes and dimensions, and mechanical requirements for the manufacture of two types of individually dogged watertight, gastight/airtight, and weathertight doors of steel, aluminum, and glass-reinforced plastic construction. These doors, which shall be complete with frames, are built for access through bulkheads by marine personnel, and are intended to maintain the structural and tightness integrity of the bulkheads. The doors shall be classified into groups according to their area of application, as follow: Group A—watertight doors in the bridge front bulkhead and the unprotected bulkhead of deckhouses/superstructures, and deckhouses that enclose machinery openings; Group B—watertight doors in the deckhouse bulkheads partially protected or in the bulkhead of deckhouses/superstructures, and not around machinery openings, watertight and airtight doors below weather deck; Group C—airtight /gastight doors in the aft end bulkhead of the bridge, forecastle, and deckhouses at the weather deck level; and Group D—weathertight doors in the deckhouse above the weather deck level. All doors shall be certified for applicable tightness integrity prior to delivery.
SCOPE
1.1 This specification, to be used in conjunction with Specification F1073, covers the principal dimensions and the mechanical requirements for manufacturing steel, aluminum, and glass-reinforced plastic, individually dogged, watertight, gastight/airtight, and weathertight doors, for personnel access through bulkheads, complete with frames, for marine use intended to maintain the structural and tightness integrity of bulkheads.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following safety hazards caveat pertains to the test method portion, Section 8, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Published
• Publication Date: 28-Feb-2019
• ICS: 47.020.10 - Hulls and their structure elements
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Relations

• Refers: ASTM F1073-19 - Standard Specification for Door Fittings, for Watertight /Gastight /Airtight, Weathertight, and Non-Tight Doors, for Marine Use
• Effective Date: 01-Mar-2019
• Refers: ASTM A131/A131M-14 - Standard Specification for Structural Steel for Ships
• Effective Date: 01-Oct-2014

Standards Content (Sample)

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F1069 −19 An American National Standard
Standard Specification for
Doors, Watertight, Gastight/Airtight and Weathertight,
1
Individually Dogged, for Marine Use
This standard is issued under the fixed designation F1069; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F1073 Specification for Door Fittings, for Watertight
/Gastight /Airtight, Weathertight, and Non-Tight Doors,
1.1 This specification, to be used in conjunction with
for Marine Use
Specification F1073, covers the principal dimensions and the
3
mechanical requirements for manufacturing steel, aluminum, 2.2 ABS Standard:
and glass-reinforced plastic, individually dogged, watertight, Rules for Building and Classing Steel Vessels
gastight/airtight, and weathertight doors, for personnel access 4
2.3 Military Standards:
through bulkheads, complete with frames, for marine use
MIL-R-900 Rubber Gasket Material (45 Durometer Hard-
intended to maintain the structural and tightness integrity of
ness)
bulkheads.
MIL-P-17549 Plastic Laminates, Fibrous Glass Reinforced
1.2 The values stated in inch-pound units are to be regarded MIL-G-17927 Gaskets, Glass-Metallic Cover, Silicone Core
as the standard. The values given in parentheses are for MIL-R-21607 Resins, Polyester Low-Pressure Laminating
information only. Fire Retardant
MIL-P-24441 Epoxy-Polyamide Paint
1.3 The following safety hazards caveat pertains to the test
MIL-PRF-24635 Silicone-Alkyd Enamel Paint Weather-
method portion, Section 8, of this specification: This standard
Resistant, Exterior Use
does not purport to address all of the safety concerns, if any,
MIL-C-81706 Coating, Aluminum and Aluminum Alloys
associatedwithitsuse.Itistheresponsibilityoftheuserofthis
NAVSEA SI 009-32 Cleaning and Painting Requirements;
standard to establish appropriate safety, health, and environ-
accomplish
mental practices and determine the applicability of regulatory
limitations prior to use.
3. Classification
1.4 This international standard was developed in accor-
dance with internationally recognized principles on standard-
3.1 The doors shall be classified into groups as given in
ization established in the Decision on Principles for the
Table 1, according to their application; in addition, the length
Development of International Standards, Guides and Recom-
“L” shall be in accordance with the ABS Rules for Building
mendations issued by the World Trade Organization Technical
and Classing Steel Vessels.
Barriers to Trade (TBT) Committee.
3.2 The doors shall be of two types. Type I doors shall
conform to all dimensions, scantlings, and details of this
2. Referenced Documents
specification. Type II doors shall be to special openings
2
2.1 ASTM Standards:
conforming to the test methods of this specification and
A36/A36M Specification for Carbon Structural Steel
scantlings indicated in Figs. 1-4. Special built doors with more
A131/A131M Specification for Structural Steel for Ships
than 9 psi (62 kPa) shall be indicated in the ordering informa-
B209 Specification for Aluminum and Aluminum-Alloy
tion (see Supplementary Requirements).
Sheet and Plate
1
3.2.1 Tolerances of all doors shall be 6 ⁄8 in. (3 mm).
3.3 Where structural fire protection requirements are
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
applicable, the doors shall meet the same requirements as
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
required for the bulkheads in which fitted.
Outfitting and Deck Machinery.
Current edition approved March 1, 2019. Published March 2019. Originally
approved in 1987. Last previous edition approved in 2012 as F1069 – 87 (2012).
DOI: 10.1520/F1069-19.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Bureau of Shipping (ABS), ABS Plaza, 16855
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Northchase Dr., Houston, TX 77060, http://www.eagle.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,
the ASTM website. Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1069−19
TABLE 1 Door Groups
Group Application
A
A (WT) Doors in the bridge
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1069 − 87 (Reapproved 2012) F1069 − 19 An American National Standard
Standard Specification for
Doors, Watertight, Gastight/Airtight and Weathertight,
1
Individually Dogged, for Marine Use
This standard is issued under the fixed designation F1069; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification, to be used in conjunction with Specification F1073, covers the principal dimensions and the mechanical
requirements for manufacturing steel, aluminum, and glass-reinforced plastic, individually dogged, watertight, gastight/airtight,
and weathertight doors, for personnel access through bulkheads, complete with frames, for marine use intended to maintain the
structural and tightness integrity of bulkheads.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.3 The following safety hazards caveat pertains to the test method portion, Section 8, of this specification: This standard does
not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard
to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability of regulatory
limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A131/A131M Specification for Structural Steel for Ships
B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate
F1073 Specification for Door Fittings, for Watertight /Gastight /Airtight, Weathertight, and Non-Tight Doors, for Marine Use
3
2.2 ABS Standard:
Rules for Building and Classing Steel Vessels
4
2.3 Military Standards:
MIL-R-900 Rubber Gasket Material (45 Durometer Hardness)
MIL-R-21607 Resins, Polyester Low-Pressure Laminating Fire Retardant
MIL-P-17549 Plastic Laminates, Fibrous Glass Reinforced
MIL-G-17927 Gaskets, Glass-Metallic Cover, Silicone Core
MIL-R-21607 Resins, Polyester Low-Pressure Laminating Fire Retardant
MIL-P-24441 Epoxy-Polyamide Paint
MIL-PRF-24635 Silicone-Alkyd Enamel Paint Weather-Resistant, Exterior Use
MIL-C-81706 Coating, Aluminum and Aluminum Alloys
MIL-P-24441 Epoxy-Polyamide Paint
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
Current edition approved April 1, 2012March 1, 2019. Published November 2012March 2019. Originally approved in 1987. Last previous edition approved in 20042012
as F1069 – 87 (2004).(2012). DOI: 10.1520/F1069-87R12.10.1520/F1069-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Bureau of Shipping (ABS), ABS Plaza, 16855 Northchase Dr., Houston, TX 77060, http://www.eagle.org.
4
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA
19111-5098, http://dodssp.daps.dla.mil.19111-5094, http://quicksearch.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1069 − 19
DoD-STD-2138NAVSEA SI 009-32 Metal Sprayed Coating Systems for Corrosion ProtectionCleaning and Painting Require-
ments; accomplish
TT-E-490 Enamel Silicone Alkyd Copolymer, Semi-gloss Exterior
3. Classification
3.1 The doors shall be classified into groups as given in Table 1, according to their application; in addition, the length “L” shall
be in accordance with the ABS Rules for Building and Classing Steel Vessels.
3.2 The doors shall be of two types. Type I doors shall conform to all dimensions, scantlings, and details of
...