ASTM F2111-01a(2017)

Standard Practice for Measuring Intergranular Attack or End Grain Pitting on Metals Caused by Aircraft Chemical Processes

SIGNIFICANCE AND USE
4.1 If not properly qualified, chemicals and chemical processes can attack metals used during aircraft maintenance and production. It is important to qualify only processes and chemical formulas that do not have any deleterious effects on aircraft metallic skins, fittings, components, and structures. This test procedure is used to detect and measure intergranular attack or pitting depth caused by aircraft maintenance chemical processes, hence, this test procedure is useful in selecting a process that will not cause intergranular attack or end grain pitting on aircraft alloys.  
4.2 The purpose of this practice is to aid in the qualification or process conformance testing or production of maintenance chemicals for use on aircraft.  
4.2.1 Actual aircraft processes in the production environment shall give the most representative results; however, the test results cannot be completely evaluated with respect to ambient conditions which normally vary from day to day. Additionally, when testing chemicals requiring dilutions, water quality and composition can play a role in the corrosion rates and mechanism affecting the results.  
4.2.2 Some examples of maintenance and production chemicals include: organic solvents, paint strippers, cleaners, deoxidizers, water-based or semi-aqueous cleaners, or etching solutions and chemical milling solutions.
SCOPE
1.1 This practice covers the procedures for testing and measuring intergranular attack (IGA) and end grain pitting on aircraft metals and alloys caused by maintenance or production chemicals.  
1.2 The standard does not purport to address all qualification testing parameters, methods, critical testing, or criteria for aircraft production or maintenance chemical qualifications. Specific requirements and acceptance testing along with associated acceptance criteria shall be found where applicable in procurement specifications, materials specifications, appropriate process specifications, or previously agreed upon specifications.  
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-May-2017
• ICS: 19.040 - Environmental testing
• ICS: 49.025.01 - Materials for aerospace construction in general
• Technical Committee: F07 - Aerospace and Aircraft
• Drafting Committee: F07.07 - Qualification Testing of Aircraft Cleaning Materials

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F2111 − 01a (Reapproved 2017)
Standard Practice for
Measuring Intergranular Attack or End Grain Pitting on
1
Metals Caused by Aircraft Chemical Processes
This standard is issued under the fixed designation F2111; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope G1Practice for Preparing, Cleaning, and Evaluating Corro-
sion Test Specimens
1.1 This practice covers the procedures for testing and
G15Terminology Relating to Corrosion and CorrosionTest-
measuring intergranular attack (IGA) and end grain pitting on
3
ing (Withdrawn 2010)
aircraftmetalsandalloyscausedbymaintenanceorproduction
G46Guide for Examination and Evaluation of Pitting Cor-
chemicals.
rosion
1.2 The standard does not purport to address all qualifica-
2.2 ASME Standard:
tion testing parameters, methods, critical testing, or criteria for
B46.1Surface Texture (Surface Roughness, Waviness, and
aircraft production or maintenance chemical qualifications.
4
Lay)
Specific requirements and acceptance testing along with asso-
ciated acceptance criteria shall be found where applicable in
3. Terminology
procurement specifications, materials specifications, appropri-
3.1 Definitions of Terms Specific to This Standard:
ate process specifications, or previously agreed upon specifi-
3.1.1 longitudinal grain direction (L)—the dimension par-
cations.
allel to the rolling or extruded direction of the extrusion in the
1.3 The values stated in SI units are to be regarded as the
original shape.
standard. The values given in parentheses are for information
3.1.2 long transverse (LT)—the longest dimension perpen-
only.
dicular to the rolling or extruded direction of the extrusion in
1.4 This standard does not purport to address all of the
the original shape.
safety concerns, if any, associated with its use. It is the
3.1.3 pit—a depression or cavity with a width to depth ratio
responsibility of the user of this standard to establish appro-
of <6 to 1.
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. 3.1.4 short transverse (ST)—the shortest dimension perpen-
dicular to the rolling or extruded direction of the extrusion in
1.5 This international standard was developed in accor-
dance with internationally recognized principles on standard- the original shape.
ization established in the Decision on Principles for the
3.1.5 surface roughness (R )—filtered mean line µin. (µm)
a
Development of International Standards, Guides and Recom-
as defined in ASME B46.1, Surface Texture.
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
4. Significance and Use
4.1 If not properly qualified, chemicals and chemical pro-
2. Referenced Documents
cesses can attack metals used during aircraft maintenance and
2
2.1 ASTM Standards:
production. It is important to qualify only processes and
E3Guide for Preparation of Metallographic Specimens
chemical formulas that do not have any deleterious effects on
aircraft metallic skins, fittings, components, and structures.
This test procedure is used to detect and measure intergranular
1
attackorpittingdepthcausedbyaircraftmaintenancechemical
This practice is under the jurisdiction ofASTM Committee F07 on Aerospace
and Aircraft and is the direct responsibility of Subcommittee F07.07 on Qualifica-
processes, hence, this test procedure is useful in selecting a
tion Testing of Aircraft Cleaning Materials.
CurrenteditionapprovedJune1,2017.PublishedJuly2017.Originallyapproved
in 2001. Last previous edition approved in 2011 as F2111–01a (2011). DOI:
3
10.1520/F2111-01AR17. The last approved version of this historical standard is referenced on
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or www.astm.org.
4
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Available from American Society of Mechanical Engineers (ASME), ASME
Standards volume information, refer to the standard’s Document Summary page on International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
the ASTM website. www.asme.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2111 − 01a (2017)
process that will not cause intergranular attack or end grain 6.1.2 Cut out metallurgical test specimen and polish FaceA
pitting on aircraft alloys. to0.812µm(32µin.)R orpreferablyfinerwithpolishasgiven
a
in 5.3.
4.2 The purpose of this practice is to aid in the qualification
or process conformance
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F2111 − 01a (Reapproved 2011) F2111 − 01a (Reapproved 2017)
Standard Practice for
Measuring Intergranular Attack or End Grain Pitting on
1
Metals Caused by Aircraft Chemical Processes
This standard is issued under the fixed designation F2111; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice covers the procedures for testing and measuring intergranular attack (IGA) and end grain pitting on aircraft
metals and alloys caused by maintenance or production chemicals.
1.2 The standard does not purport to address all qualification testing parameters, methods, critical testing, or criteria for aircraft
production or maintenance chemical qualifications. Specific requirements and acceptance testing along with associated acceptance
criteria shall be found where applicable in procurement specifications, materials specifications, appropriate process specifications,
or previously agreed upon specifications.
1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
E3 Guide for Preparation of Metallographic Specimens
G1 Practice for Preparing, Cleaning, and Evaluating Corrosion Test Specimens
3
G15 Terminology Relating to Corrosion and Corrosion Testing (Withdrawn 2010)
G46 Guide for Examination and Evaluation of Pitting Corrosion
2.2 ASME Standard:
4
B46.1 Surface Texture (Surface Roughness, Waviness, and Lay)
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 longitudinal grain direction (L)—the dimension parallel to the rolling or extruded direction of the extrusion in the original
shape.
3.1.2 long transverse (LT)—the longest dimension perpendicular to the rolling or extruded direction of the extrusion in the
original shape.
3.1.3 pit—a depression or cavity with a width to depth ratio of <6 to 1.
3.1.4 short transverse (ST)—the shortest dimension perpendicular to the rolling or extruded direction of the extrusion in the
original shape.
1
This practice is under the jurisdiction of ASTM Committee F07 on Aerospace and Aircraft and is the direct responsibility of Subcommittee F07.07 on Qualification
Testing of Aircraft Cleaning Materials.
Current edition approved Dec. 1, 2011June 1, 2017. Published August 2012July 2017. Originally approved in 2001. Last previous edition approved in 20052011 as
F2111 – 01a (2005).(2011). DOI: 10.1520/F2111-01AR11.10.1520/F2111-01AR17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
www.asme.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F2111 − 01a (2017)
3.1.5 surface roughness (R )—filtered mean line μin. (μm) as defined in ASME B46.1, Surface Texture.
a
4. Significance and Use
4.1 If not properly qualified, chemicals and chemical processes can attack metals used during aircraft maintenance and
production. It is important to qualify only processes and chemical formulas that do not have any deleterious effects on aircraft
metallic skins, fittings, components, and structures. This test procedure is used to detect and measure intergranular attack or pitting
depth caused by aircraft maintenance ch
...