iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F655-13

(Specification)

Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing (Withdrawn 2022)

Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing (Withdrawn 2022)

ABSTRACT
This specification provides the construction details, replacement procedures, and selection criteria for the standard test carpets and pads used when testing vacuum cleaners. The carpet types, which shall be constructed in accordance with the physical requirements provided herein, are classified as follows: shag custom tufted test carpet; plush custom tufted test carpet; multilevel custom tufted test carpet; and level loop test carpet. Padding, on the other hand, shall be of the sponge rubber type of waffle construction with a reinforcing skrim.
SCOPE
1.1 This specification provides construction details and a replacement procedure for the standard carpet and pad to be used when testing vacuum cleaners.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
WITHDRAWN RATIONALE
This specification provides construction details and a replacement procedure for the standard carpet and pad to be used when testing vacuum cleaners.
Formerly under the jurisdiction of Committee F11 on Vacuum Cleaners, this specification was withdrawn in July 2022 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

General Information

Status
Withdrawn
Publication Date
31-May-2013
Withdrawal Date
18-Jul-2022
ICS
97.080 - Cleaning appliances
97.150 - Floor coverings
Technical Committee
F11 - Vacuum Cleaners
Drafting Committee
F11.21 - Cleanability
Current Stage
Ref Project

Buy Standard

ASTM F655-13 - Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing (Withdrawn 2022)ASTM F655-13 - Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing (Withdrawn 2022)
PreviousNext
Technical specification
ASTM F655-13 - Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing (Withdrawn 2022)
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F655 −13
Standard Specification for
1
Test Carpets and Pads for Vacuum Cleaner Testing
ThisstandardisissuedunderthefixeddesignationF655;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F2756 TestMethodforDeterminingEnergyConsumptionof
Vacuum Cleaners
1.1 This specification provides construction details and a
F2797 Test Method for Evaluating Edge Cleaning Effective-
replacement procedure for the standard carpet and pad to be
ness of Vacuum Cleaners
used when testing vacuum cleaners.
1.2 The values stated in inch-pound units are to be regarded
3. Basis of Selection
as the standard. The values given in parentheses are for
3.1 These standard carpets and pads are intended to provide
information only.
a database and shall meet the following requirements:
3.1.1 Representative of carpets currently in popular use in
2. Referenced Documents
the United States.
2
2.1 ASTM Standards:
3.1.2 Reasonable anticipation of continued availability.
F555 Test Method for Motor Life Evaluation of an Upright
3.1.3 Compatible with other ASTM Committee F11 meth-
Vacuum Cleaner
ods.
F608 Test Method for Evaluation of Carpet Embedded Dirt
3.1.4 Provide a separation of cleaning effectiveness ratings
Removal Effectiveness of Household/Commercial
between products with good reliability and repeatability.
Vacuum Cleaners
F922 Test Method for Motor Life Evaluation of an Electric
4. Classification
Motorized Nozzle
4.1 The carpet types shall be classified according to ac-
F1284 Test Method for Evaluating Carpet Embedded Dirt
cepted carpet industry practice, such as shag, multilevel, plush,
Removal Effectiveness of Residential Central Vacuum
etc.
Cleaning Systems
F1334 Test Method for Determining A-Weighted Sound
5. Physical Requirements
Power Level of Vacuum Cleaners
3
5.1 Carpets —The following carpet types and construction
F1409 Test Method for Straight Line Movement of Vacuum
have been found acceptable for use in vacuum cleaner testing.
Cleaners While Cleaning Carpets
They shall be made in accordance with the physical require-
F1411 Practice for Presenting Selected Information on
ments given in Table 1, Table 2 and Table 3.
Vacuum Cleaners for Consumer Use
F1601 Test Method for Motor Life Evaluation of an Electric
NOTE 1—A variance of 67 % in face weight is allowable per HUD
Motorized Nozzle for Central Vacuum Cleaning Systems
guidelines. When a new construction is needed, the proposed custom
F1692 Test Method for Life Evaluation of a Turbine- tufted test carpets should be subjected to construction verification as well
as cleanability testing prior to acceptance for use.
Powered Nozzle for Household Central Vacuum Cleaning
4
Systems
5.2 Padding —Sponge rubber type of waffle construction
F2609 Test Method for Litter-Cleaning Effectiveness of with a reinforcing skrim. See Table 4 for a description of the
Vacuum Cleaners
construction.
1 3
This specification is under the jurisdiction of ASTM Committee F11 on The central source for the test carpets at this time is SDLAtlas, 3934 Airway
Vacuum Cleaners and is the direct responsibility of Subcommittee F11.21 on Drive,RockHill,SC29732.Ifyouareawareofalternativesuppliers,pleaseprovide
Cleanability. this information to ASTM International Headquarters. Your comments will receive
1
CurrenteditionapprovedJune1,2013.PublishedJuly2013.Originallyapproved careful consideration at a meeting of the responsible technical committee, which
in1980.Lastpreviouseditionapprovedin2011asF655 – 11.DOI:10.1520/F0655- you may attend.
4
13. The sole source of supply of the padding (Grandstand) is General Felt
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Industries, Co., 80 Park Plaza West-One, Saddlebrook, NJ 07662-5864. If you are
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM aware of alternative suppliers, please provide this information to ASTM Interna-
Standards volume information, refer to the standard’s Document Summary page on tional Headquarters.Your comments will receive careful consideration at a meeting
1
the ASTM website. of the responsible technical committee, which you may attend.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F655−13
TABLE 1 Custom Carpet Construction Specifications
Plush Multi-Level Frieze Level Loop
Woven
Construction Tufted Tufted Tufted
(through back)
1 1 1
Gauge/Pitch ⁄9 in., no shift ⁄10 in., no shift ⁄8 in., no shift 216
Pile Height 0.5 ± 0.02 in. (12.7 ± 0.5 mm) 0.416 ± 0.02 in. (10.6 ± 0.5 m
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F655-11(Specification)
Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing

ABSTRACT
This specification provides the construction details, replacement procedures, and selection criteria for the standard test carpets and pads used when testing vacuum cleaners. The carpet types, which shall be constructed in accordance with the physical requirements provided herein, are classified as follows: shag custom tufted test carpet; plush custom tufted test carpet; multilevel custom tufted test carpet; and level loop test carpet. Padding, on the other hand, shall be of the sponge rubber type of waffle construction with a reinforcing skrim.
SCOPE
1.1 This specification provides construction details and a replacement procedure for the standard carpet and pad to be used when testing vacuum cleaners.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F655-11(Specification)
Standard Specification for Test Carpets and Pads for Vacuum Cleaner Testing

ABSTRACT
This specification provides the construction details, replacement procedures, and selection criteria for the standard test carpets and pads used when testing vacuum cleaners. The carpet types, which shall be constructed in accordance with the physical requirements provided herein, are classified as follows: shag custom tufted test carpet; plush custom tufted test carpet; multilevel custom tufted test carpet; and level loop test carpet. Padding, on the other hand, shall be of the sponge rubber type of waffle construction with a reinforcing skrim.
SCOPE
1.1 This specification provides construction details and a replacement procedure for the standard carpet and pad to be used when testing vacuum cleaners.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM A370-23(Test Method)
Standard Test Methods and Definitions for Mechanical Testing of Steel Products

SIGNIFICANCE AND USE
4.1 The primary use of these test methods is testing to determine the specified mechanical properties of steel, stainless steel, and related alloy products for the evaluation of conformance of such products to a material specification under the jurisdiction of ASTM Committee A01 and its subcommittees as designated by a purchaser in a purchase order or contract.  
4.1.1 These test methods may be and are used by other ASTM Committees and other standards writing bodies for the purpose of conformance testing.  
4.1.2 The material condition at the time of testing, sampling frequency, specimen location and orientation, reporting requirements, and other test parameters are contained in the pertinent material specification or in a general requirement specification for the particular product form.  
4.1.3 Some material specifications require the use of additional test methods not described herein; in such cases, the required test method is described in that material specification or by reference to another appropriate test method standard.  
4.2 These test methods are also suitable to be used for testing of steel, stainless steel and related alloy materials for other purposes, such as incoming material acceptance testing by the purchaser or evaluation of components after service exposure.  
4.2.1 As with any mechanical testing, deviations from either specification limits or expected as-manufactured properties can occur for valid reasons besides deficiency of the original as-fabricated product. These reasons include, but are not limited to: subsequent service degradation from environmental exposure (for example, temperature, corrosion); static or cyclic service stress effects, mechanically-induced damage, material inhomogeneity, anisotropic structure, natural aging of select alloys, further processing not included in the specification, sampling limitations, and measuring equipment calibration uncertainty. There is statistical variation in all aspects of mechanical testin...
SCOPE
1.1 These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.  
1.2 The following mechanical tests are described:    
Sections  
Tension  
7 to 14  
Bend  
15  
Hardness  
16  
Brinell  
17  
Rockwell  
18  
Portable  
19  
Impact  
20 to 30  
Keywords  
32  
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:    
Annex  
Bar Products  
Annex A1  
Tubular Products  
Annex A2  
Fasteners  
Annex A3  
Round Wire Products  
Annex A4  
Significance of Notched-Bar Impact Testing  
Annex A5  
Converting Percentage Elongation of Round Specimens to
Equivalents for Flat Specimens  
Annex A6    
Testing Multi-Wire Strand  
Annex A7  
Rounding of Test Data  
Annex A8  
Methods for Testing Steel Reinforcing Bars  
Annex A9  
Procedure for Use and Control of Heat-cycle Simulation  
Annex A10  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 When these test methods are referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 in. or 8 in. may be report...

  • Standard
    51 pages
    English language
    sale 15% off
  • Standard
    51 pages
    English language
    sale 15% off
ASTM
ASTM F1960-23b(Specification)
Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

ABSTRACT
This specification covers cold expansion fittings and cross-linked (PEX) reinforcing rings for use with cross-linked polyethylene (PEX) plastic tubing in specific nominal diameters. These fittings are intended for use in residential and commercial, hot and cold, potable water distribution systems as well as sealed central heating, including under-floor-heating systems. The PEX reinforcing rings shall conform to the required density, degree of cross-linking, and stabilizer migration resistance.
SCOPE
1.1 This specification covers cold expansion fittings and cross-linked (PEX) reinforcing rings for use with cross-linked polyethylene (PEX) plastic tubing in nominal tubing sizes of 3/8 , 1/2 , 5/8 , 3/4 , 1, 11/4 , 11/2 , 2, 21/2 , and 3 in. that meet the requirements of Specification F876 or F3253 and for use with Polyethylene of Raised Temperature (PE-RT) pipe in nominal tubing sizes of 3/8 , 1/2 , 5/8 , 3/4 , 1, 11/4 , 11/2 , 2, 21/2 , and 3 that meet the requirements of Specification F2769. These fittings are intended for use in 100 psi (690 kPa) cold- and hot-water distribution systems operating at temperatures up to and including 180 °F (82 °C). The system is comprised of a PEX reinforcing ring and a cold expansion fitting. Included are the requirements for materials, workmanship, dimensions, and markings to be used on the fitting components. The components covered by this specification are intended for use in residential and commercial, hot and cold, potable water distribution systems as well as building supply lines, sealed central heating, including under-floor-heating systems.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM E2521-23(Terminology)
Standard Terminology for Evaluating Response Robot Capabilities

SCOPE
1.1 This terminology identifies and precisely defines terms as used in the standard test methods, practices, and guides for evaluating response robots intended for hazardous environments. Further discussions of the terms can be found within the standards in which the terms appear.  
1.2 The term definitions address response robots, including ground, aquatic, and aerial systems. Some key features of such systems are remotely operated from safe standoff distances, deployable at operational tempos, capable of operating in complex environments, sufficiently hardened against harsh environments, reliable and field serviceable, durable or cost effectively disposable, and equipped with operational safeguards.  
1.3 Units—Values stated in either the International System of Units (metric) or U.S. Customary units (inch-pound) are to be regarded separately as standard. The values stated in each system may not be exact equivalents. Both units are referenced to facilitate acquisition of materials internationally and minimize fabrication costs. Tests conducted using either system maintain repeatability and reproducibility of the test method and results are comparable.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM C1306/C1306M-08(2023)(Test Method)
Standard Test Method for Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane

SIGNIFICANCE AND USE
5.1 This test method is used as a screening tool to determine the hydrostatic pressure to which a liquid-applied waterproofing membrane may be subjected without failing when stretched over a crack in the substrate. This test method discriminates between a membrane that is very resistant to hydrostatic pressure and one that is not. Because of the variability inherent in this test method, it is not recommended that this test method be used to set a numerical standard for hydrostatic pressure resistance. No prediction of durability at lower hydrostatic pressures can be made when using the results of this test method.
SCOPE
1.1 This test method describes a laboratory procedure for determining the resistance of a waterproofing membrane to hydrostatic pressure.  
1.2 The committee with jurisdiction over this standard is not aware of any comparable standards published by other organizations.  
1.3 There are no ISO standards similar or equivalent to this ASTM standard.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F2647-07(2023)(Guide)
Standard Guide for Approved Methods of Installing a CVS (Central Vacuum System)

SIGNIFICANCE AND USE
4.1 The suggestions of this guide are intended to provide proper installation materials and practices to be used during the installation of a central-vacuum system.
SCOPE
1.1 This guide demonstrates proper methods for installing a central-vacuum system.  
1.2 Appendix X1 contains additional sources of information that may be helpful to the user of this guide.  
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4725-15(2023)(Terminology)
Standard Terminology for Engine Coolants and Related Fluids

SCOPE
1.1 This document covers terminology relating to engine coolants. It is intended to provide a reference for anyone seeking information on engine coolants, and also to provide a uniform set of definitions for use in preparing ASTM specifications, test methods and other standard documents.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM F3331-18(2023)(Practice)
Standard Practice for Aircraft Water Loads

SIGNIFICANCE AND USE
4.1 This practice provides one means for determining the aeroplane structural loads for either dual floats or single hulls when taxiing on, taking off from, or landing on water. This practice satisfies the water loads requirements set forth in the Design Loads and Conditions Specification for Normal Category Aeroplanes.
SCOPE
1.1 This practice provides equations for calculating water loads for aeroplane dual floats and single hulls. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Level 1, 2, 3, and 4 Normal Category aeroplanes. The content may be more broadly applicable; it is the responsibility of the Applicant to substantiate broader applicability as a specific means of compliance.  
1.2 An applicant intended to propose this information as Means of Compliance for a design approval must seek guidance from their respective oversight authority (for example, published guidance from applicable CAAs) concerning the acceptable use and application thereof. For information on which oversight authorities have accepted this standard (in whole or in part) as an acceptable Means of Compliance to their regulatory requirements (hereinafter “the Rules”), refer to ASTM Committee F44 web page (www.astm.org/COMMITTEE/F44.htm).  
1.3 Units—The values stated in inch-pound units are to be regarded as standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM A999/A999M-23(Specification)
Standard Specification for General Requirements for Alloy and Stainless Steel Pipe

SCOPE
1.1 This specification2 covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.  
1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail.    
Title of Specification  
ASTM Desig-
nation3  
Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes  
A312/A312M  
Seamless and Welded Steel Pipe for Low-Temperature
Service and Other Applications with Required Notch
Toughness  
A333/A333M  
Seamless Ferritic Alloy-Steel Pipe for High Temperature
Service  
A335/A335M  
Electric-Fusion-Welded Austenitic Chromium-Nickel Stainless
Steel Pipe for High-Temperature Service and General
Applications  
A358/A358M  
Carbon and Ferritic Alloy Steel Forged and Bored Pipe for
High-Temperature Service  
A369/A369M  
Seamless Austenitic Steel Pipe for High-Temperature
Service  
A376/A376M  
Welded Large Diameter Austenitic Steel Pipe for Corrosive
or High-Temperature Service  
A409/A409M  
Centrifugally Cast Ferritic Alloy Steel Pipe for
High-Temperature Service  
A426/A426M  
Centrifugally Cast Austenitic Steel Pipe for High-
Temperature Service  
A451/A451M  
Centrifugally Cast Iron-Chromium-Nickel High-Alloy
Tubing for Pressure Application at High
Temperatures  
A608/A608M  
Welded, Unannealed Austenitic Stainless Steel Tubular
Products  
A778/A778M  
Seamless and Welded Ferritic/Austenitic
Stainless Steel Pipe  
A790/A790M  
Single- or Double-Welded Austenitic Stainless Steel Pipe  
A813/A813M  
Cold-Worked Welded Austenitic Stainless Steel Pipe  
A814/A814M  
Centrifugally Cast Ferritic/Austenitic Stainless Steel Pipe
for Corrosive Environments  
A872/A872M  
Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric
Fusion Welded with Addition of Filler Metal  
A928/A928M  
Spray-Formed Seamless Austenitic Stainless Steel Pipes  
A943/A943M  
Spray-Formed Seamless Ferritic/Austenitic Stainless Steel Pipe  
A949/A949M  
Austenitic Chromium-Nickel-Silicon Alloy Steel Seamless
and Welded Pipe  
A954  
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units apply unless the “M” designation (SI) of the product specification is specified in the order.
Note 1: The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as “nominal diameter,” “size,” “nominal bore,” and “nominal size.”  
1.4 The following precautionary statement pertains only to the test method portion, Section 21, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    12 pages
    English language
    sale 15% off
  • Technical specification
    12 pages
    English language
    sale 15% off