ASTM E1537-02a

Standard Test Method for Fire Testing of Upholstered Furniture

SCOPE
1.1 This is a fire-test-response standard.
1.2 The purpose of this test method is to determine the burning behavior of upholstered furniture used in public occupancies by measuring specific fire-test responses when the specimen of furniture is subjected to a specified flaming ignition source under well-ventilated conditions.
1.3 Data are obtained describing the burning behavior from a specific ignition source until all burning has ceased, a period of 1 h has elapsed, or flashover appears inevitable.
1.4 This test method does not provide information on the fire performance of upholstered furniture in fire conditions other than those conditions specified. In particular, this test method does not apply to smoldering ignition by cigarettes. See X1.6 for further information.
1.5 The rate of heat release of the burning specimen is measured by an oxygen consumption method. See X1.6.4 for further information.
1.6 The production of light obscuring smoke is measured and the concentrations of certain toxic gas species in the combustion gases are determined. See X1.6.5 for further information.
1.7 The burning behavior is visually documented by photographic or video recordings, whenever possible.
1.8 The system of units to be used in referee decisions is the SI system of units, see Practice E 380 only. The units given in parentheses are for information only.
1.9 This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products or assemblies under actual fire conditions.
1.10 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 09-Sep-2002
• ICS: 13.220.40 - Ignitability and burning behaviour of materials and products
• ICS: 97.140 - Furniture
• Technical Committee: E05 - Fire Standards
• Drafting Committee: E05.15 - Furnishings and Contents

Relations

• Replaces: ASTM E1537-02 - Standard Test Method for Fire Testing of Real Scale Upholstered Furniture
• Effective Date: 10-Sep-2002
• Replaced By: ASTM E1537-07 - Standard Test Method for Fire Testing of Upholstered Furniture
• Effective Date: 01-May-2007
• Referred By: ASTM E176-21ae1 - Standard Terminology of Fire Standards
• Effective Date: 10-Sep-2002
• Referred By: ASTM F1550-22 - Standard Test Method for Determination of Fire-Test-Response Characteristics of Components or Composites of Mattresses or Furniture for Use in Correctional Facilities after Exposure to Vandalism, by Employing a Bench Scale Oxygen Consumption Calorimeter
• Effective Date: 10-Sep-2002
• Referred By: ASTM E2102-21 - Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
• Effective Date: 10-Sep-2002
• Referred By: ASTM E1590-23 - Standard Test Method for Fire Testing of Mattresses
• Effective Date: 10-Sep-2002
• Referred By: ASTM E2574/E2574M-17(2021) - Standard Test Method for Fire Testing of School Bus Seat Assemblies
• Effective Date: 10-Sep-2002
• Referred By: ASTM F1870-22 - Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities
• Effective Date: 10-Sep-2002
• Referred By: ASTM E603-23 - Standard Guide for Room Fire Experiments
• Effective Date: 10-Sep-2002
• Referred By: ASTM E2061-23 - Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles
• Effective Date: 10-Sep-2002
• Referred By: ASTM E3020-22 - Standard Practice for Ignition Sources
• Effective Date: 10-Sep-2002
• Referred By: ASTM E2280-21 - Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture Within Patient Rooms of Health Care Facilities
• Effective Date: 10-Sep-2002
• Referred By: ASTM E1822-21 - Standard Test Method for Fire Testing of Stacked Chairs
• Effective Date: 10-Sep-2002
• Referred By: ASTM E2067-22 - Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests
• Effective Date: 10-Sep-2002
• Referred By: ASTM E1995-21 - Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, With the Test Specimen Oriented Horizontally
• Effective Date: 10-Sep-2002

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: E 1537 – 02a
Standard Test Method for
1
Fire Testing of Upholstered Furniture
This standard is issued under the fixed designation E1537; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 1.11 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
1.1 This is a fire-test-response standard.
responsibility of the user of this standard to establish appro-
1.2 The purpose of this test method is to determine the
priate safety and health practices and determine the applica-
burning behavior of upholstered furniture used in public
bility of regulatory limitations prior to use.
occupanciesbymeasuringspecificfire-testresponseswhenthe
specimen of furniture is subjected to a specified flaming
2. Referenced Documents
ignition source under well-ventilated conditions.
2.1 ASTM Standards:
1.3 Data are obtained describing the burning behavior from
2
D123 Terminology Relating to Textiles
a specific ignition source until all burning has ceased, a period
E84 Test Method for Surface Burning Characteristics of
of 1 h has elapsed, or flashover appears inevitable.
3
Building Materials
1.4 This test method does not provide information on the
3
E176 Terminology of Fire Standards
fire performance of upholstered furniture in fire conditions
E380 Practice for Use of the International System of Units
other than those conditions specified. In particular, this test
4
(SI) (the Modernized Metric System)
method does not apply to smoldering ignition by cigarettes.
E800 Guide for Measurement of Gases Present or Gener-
See X1.6 for further information.
3
ated During Fires
1.5 The rate of heat release of the burning specimen is
E1354 Test Method for Heat and Visible Smoke Release
measured by an oxygen consumption method. See X1.6.4 for
Rates for Materials and Products Using an Oxygen Con-
further information.
3
sumption Calorimeter
1.6 The production of light obscuring smoke is measured
2.2 ISO Standards:
and the concentrations of certain toxic gas species in the
5
ISO 3261 Fire Tests—Vocabulary
combustion gases are determined. See X1.6.5 for further
ISO 4880 Burning Behaviour of Textiles and Textile
information.
5
Products—Vocabulary
1.7 The burning behavior is visually documented by photo-
ISO 9705 Fire Tests—Full Scale Room Test for Surface
graphic or video recordings, whenever possible.
5
Products
1.8 Thesystemofunitstobeusedinrefereedecisionsisthe
2.3 UL Standard:
SI system of units, see Practice E380 only. The units given in
6
UL 1056 Fire Test of Upholstered Furniture
parentheses are for information only.
2.4 CA Standard:
1.9 This standard is used to measure and describe the
CA TechnicalBulletin133FlammabilityTestProcedurefor
response of materials, products, or assemblies to heat and
7
Seating Furniture for Use in Public Occupancies
flame under controlled conditions, but does not by itself
2.5 BSI Standard:
incorporate all factors required for fire hazard or fire risk
BS5852: Part2:FireTestsforFurniture,Part2.Methodsof
assessment of the materials, products or assemblies under
Test for the Ignitability of Upholstered Composites for
actual fire conditions.
8
Seating by Flame Sources
1.10 Fire testing of products and materials is inherently
2.6 Nordtest Standard:
hazardous, and adequate safeguards for personnel and prop-
erty shall be employed in conducting these tests. This test
method may involve hazardous materials, operations, and
2
Annual Book of ASTM Standards, Vol 07.01.
equipment.
3
Annual Book of ASTM Standards, Vol 04.07.
4
Annual Book of ASTM Standards, Vol 14.02.
5
Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
4th Floor, New York, NY 10036.
1 6
This test method is under the jurisdiction of ASTM Committee E05 on Fire Available from Underwriters Laboratories (UL), Corporate Progress, 333
Standards and is the direct responsibility of Subcommittee E05.15 on Furnishing Pfingsten Rd., Northbrook, IL 60062.
7
and Contents. Available from State of California, Department of Consumer Affairs, 3485
Current edition approved Sept. 10, 2002. Published November 2002. Originally Orange Grove Avenue, North Highlands, CA 95660.
8
published as E1537–93. Last previous edition E1537–02. AvailablefromBritishStandardsInstitution,2ParkSt.,LondonW1A2B5,UK.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
E 1537 – 02a
NordtestMethodNTFire032 UpholsteredFurniture:Burn- 5. Significance and Use
9
ing Behav
...