ASTM A1119/A1119M-23

Standard Specification for Welded Partially Corrugated Stainless Tube for Potable Water and General Service

SCOPE
1.1 This specification describes welded austenitic, ferritic, and duplex stainless steel tube on which the external and internal surface has been modified by a cold forming process to produce an intermittent corrugation for improved formability and resistance to seismic and other environmental distortions. The tubes are used for potable water service lines and other liquid delivery systems in nominal diameters from 1/2 to 2 in. [13 to 50 mm].  
1.2 The tube sizes and thicknesses usually furnished to this specification are 0.625 to 2.125 in. [15.88 to 48.60 mm], outside diameter and 0.028 to 0.049 in. [0.8 to 1.2 mm], inclusive, in wall thickness.  
1.3 The grades of austenitic, ferritic, and duplex stainless steels included in this specification shall conform to materials listed in the governing straight tube Specifications A268/A268M, A269/A269M, or A789/A789M. Selection will depend upon design and service requirements.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.5 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units.  
1.6 The following safety hazards statement pertains only to the test methods of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 28-Feb-2023
• ICS: 23.040.03 - Pipeline and its parts for external water conveyance systems
• ICS: 23.040.10 - Iron and steel pipes
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.10 - Stainless and Alloy Steel Tubular Products

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: A1119/A1119M − 23
Standard Specification for
Welded Partially Corrugated Stainless Tube for Potable
1
Water and General Service
This standard is issued under the fixed designation A1119/A1119M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.7 This international standard was developed in accor-
dance with internationally recognized principles on standard-
1.1 This specification describes welded austenitic, ferritic,
ization established in the Decision on Principles for the
and duplex stainless steel tube on which the external and
Development of International Standards, Guides and Recom-
internal surface has been modified by a cold forming process to
mendations issued by the World Trade Organization Technical
produce an intermittent corrugation for improved formability
Barriers to Trade (TBT) Committee.
and resistance to seismic and other environmental distortions.
The tubes are used for potable water service lines and other
2. Referenced Documents
1
liquid delivery systems in nominal diameters from ⁄2 to 2 in.
2
2.1 ASTM Standards:
[13 to 50 mm].
A268/A268M Specification for Seamless and Welded Fer-
1.2 The tube sizes and thicknesses usually furnished to this
ritic and Martensitic Stainless Steel Tubing for General
specification are 0.625 to 2.125 in. [15.88 to 48.60 mm],
Service
outside diameter and 0.028 to 0.049 in. [0.8 to 1.2 mm],
A269/A269M Specification for Seamless and Welded Aus-
inclusive, in wall thickness.
tenitic Stainless Steel Tubing for General Service
1.3 The grades of austenitic, ferritic, and duplex stainless
A789/A789M Specification for Seamless and Welded
steels included in this specification shall conform to materials
Ferritic/Austenitic Stainless Steel Tubing for General
listed in the governing straight tube Specifications A268/
Service
A268M, A269/A269M, or A789/A789M. Selection will de-
A1016/A1016M Specification for General Requirements for
pend upon design and service requirements.
Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless
Steel Tubes
1.4 The values stated in either SI units or inch-pound units
A1047/A1047M Test Method for Pneumatic Leak Testing of
are to be regarded separately as standard. The values stated in
Tubing
each system may not be exact equivalents; therefore, each
E384 Test Method for Microindentation Hardness of Mate-
system shall be used independently of the other. Combining
rials
values from the two systems may result in non-conformance
2.2 Other Standard:
with the standard.
JWWA G 119 Corrugated Stainless Steel Tubes for Water
1.5 This specification is expressed in both inch-pound and
Supply
SI units. However, unless the order specifies the applicable
“M” specification designation (SI units), the material shall be
3. Terminology and Symbols
furnished in inch-pound units.
3.1 Definitions—For definition of general terms used in this
1.6 The following safety hazards statement pertains only to
specification, refer to Specification A1016/A1016M.
the test methods of this specification. This standard does not
3.2 Symbols (Corrugation Nomenclature):
purport to address all of the safety concerns, if any, associated
d = outside diameter of straight section
with its use. It is the responsibility of the user of this standard 1
d = outside diameter of corrugated section
to establish appropriate safety, health, and environmental 2
L = total tube length
practices and determine the applicability of regulatory limita-
l = end to first corrugation
tions prior to use. 0
l = end to center of first corrugation
1
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
2
A01.10 on Stainless and Alloy Steel Tubular Products. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved March 1, 2023. Published May 2023. Originally contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
approved in 2020. Last previous edition approved in 2022 as A1119/A1119M – 22. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A1119_A1119M-23. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A1119/A1119M − 23
l = corrugation centerline to corrugation centerline 5.4 Lengths of the partially corrugated tube shall be sup-
2
l = last corrugation cent
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A1119/A1119M − 22 A1119/A1119M − 23
Standard Specification for
Welded Partially Corrugated Stainless Tube for Potable
1
Water and General Service
This standard is issued under the fixed designation A1119/A1119M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification describes welded austenitic, ferritic, and duplex stainless steel tube on which the external and internal
surface has been modified by a cold forming process to produce an intermittent corrugation for improved formability and resistance
to seismic and other environmental distortions. The tubes are used for potable water service lines and other liquid delivery systems
1
in nominal diameters from ⁄2 to 2 in. [13 to 50 mm].
1.2 The tube sizes and thicknesses usually furnished to this specification are 0.625 to 2.125 in. [15.88 to 48.60 mm], outside
diameter and 0.028 to 0.049 in. [0.8 to 1.2 mm], inclusive, in wall thickness.
1.3 The grades of austenitic, ferritic, and duplex stainless steels included in this specification shall conform to materials listed in
the governing straight tube Specifications A268/A268M, A269/A269M, or A789/A789M. Selection will depend upon design and
service requirements.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.5 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M”
specification designation (SI units), the material shall be furnished in inch-pound units.
1.6 The following safety hazards statement pertains only to the test methods of this specification. This standard does not purport
to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish
appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A268/A268M Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.10
on Stainless and Alloy Steel Tubular Products.
Current edition approved Oct. 15, 2022March 1, 2023. Published December 2022May 2023. Originally approved in 2020. Last previous edition approved in 20212022
as A1119 – 21.A1119/A1119M – 22. DOI: 10.1520/A1119_A1119M-22.10.1520/A1119_A1119M-23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A1119/A1119M − 23
A269/A269M Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A789/A789M Specification for Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing for General Service
A1016/A1016M Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel
Tubes
A1047/A1047M Test Method for Pneumatic Leak Testing of Tubing
E384 Test Method for Microindentation Hardness of Materials
2.2 Other Standard:
JWWA G 119 Corrugated Stainless Steel Tubes for Water Supply
3. Terminology and Symbols
3.1 Definitions—For definition of general terms used in this specification, refer to Specification A1016/A1016M.
3.2 Symbols (Corrugation Nomenclatur
...