Standard Specification for Cationic Emulsified Asphalt

ABSTRACT
This specification covers the seven grades of cationic emulsified asphalt for use in pavement construction. The asphalt shall be homogeneous after thorough mixing provided separation has not been caused by freezing and shall conform to the requirements set for viscosity, storage stability, demulsibility, coating ability and water resistance, particle charge, and distillation.
SCOPE
1.1 This specification covers seven grades of cationic emulsified asphalt for use in pavement construction in the manner designated.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Historical
Publication Date
31-May-2017
Current Stage
Ref Project

Relations

Buy Standard

Technical specification
ASTM D2397/D2397M-17 - Standard Specification for Cationic Emulsified Asphalt
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
Technical specification
REDLINE ASTM D2397/D2397M-17 - Standard Specification for Cationic Emulsified Asphalt
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D2397/D2397M −17
Standard Specification for
1
Cationic Emulsified Asphalt
This standard is issued under the fixed designation D2397/D2397M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope D6933 Test Method for Oversized Particles in Emulsified
Asphalts (Sieve Test)
1.1 This specification covers seven grades of cationic emul-
D6935 Test Method for Determining Cement Mixing of
sified asphalt for use in pavement construction in the manner
Emulsified Asphalt
designated.
D6936 Test Method for Determining Demulsibility of Emul-
1.2 The values stated in either SI units or inch-pound units
sified Asphalt
are to be regarded separately as standard. The values stated in
D6997 Test Method for Distillation of Emulsified Asphalt
each system may not be exact equivalents; therefore, each
D7226 Test Method for Determining the Viscosity of Emul-
system shall be used independently of the other. Combining
sified Asphalts Using a Rotational Paddle Viscometer
values from the two systems may result in non-conformance
D7402 Practice for Identifying Cationic EmulsifiedAsphalts
with the standard.
D7496 Test Method for Viscosity of Emulsified Asphalt by
1.3 This international standard was developed in accor- Saybolt Furol Viscometer
dance with internationally recognized principles on standard-
D7553 Test Method for Solubility of Asphalt Materials in
ization established in the Decision on Principles for the N-Propyl Bromide
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
3. Requirements
Barriers to Trade (TBT) Committee.
3.1 The emulsified asphalt shall be tested within 14 days of
delivery. The emulsified asphalt shall be homogeneous after
2. Referenced Documents
thorough mixing provided separation has not been caused by
2
2.1 ASTM Standards:
freezing. Emulsions separated by freezing shall not be tested.
D5/D5M Test Method for Penetration of Bituminous Mate-
rials 3.2 Emulsified asphalt shall conform to the requirements
prescribed in Table 1. Specify the test method to be used.
D113 Test Method for Ductility of Bituminous Materials
3
Specify either Test Method D7226 or D7496.
(Withdrawn 2016)
D140/D140M Practice for Sampling Asphalt Materials
D244 Test Methods and Practices for Emulsified Asphalts 4. Sampling
D2042 Test Method for Solubility of Asphalt Materials in
4.1 Samples of emulsified asphalt shall be taken in accor-
Trichloroethylene
dance with Practice D140/D140M.
D3910 Practices for Design, Testing, and Construction of
4.2 Samples shall be stored in clean, airtight sealed contain-
Slurry Seal
ers at a temperature of not less than 4 °C [39.2 °F] until tested.
D6930 Test Method for Settlement and Storage Stability of
Emulsified Asphalts
5. Test Methods
1
This specification is under the jurisdiction of ASTM Committee D04 on Road
5.1 The properties of the emulsified asphalts given in Table
and Paving Materials and is the direct responsibility of Subcommittee D04.41 on
1 shall be determined in accordance with the followingASTM
Emulsified Asphalt Specifications.
standards:
Current edition approved June 1, 2017. Published June 2017. Originally
approved in 1965. Last previous edition approved in 2013 as D2397/D2397M – 13. 5.1.1 Viscosity—Test Method D7496 or D7226 for Table 1.
DOI: 10.1520/D2397_D2397M-17.
5.1.2 Storage Stability—Test Method D6930.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
5.1.3 Demulsibility—Test Method D6936.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
5.1.4 Coating Ability and Water Resistance—Test Methods
the ASTM website.
D244.
3
The last approved version of this historical standard is referenced on
www.astm.org. 5.1.5 Particle Charge—Practice D7402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2397/D2397M−17
2
TABLE 1 Requirements for Cationic Emulsified Asphalt
NOTE 1—CQS-1h emulsions shall meet the requirements outlined in Practices D3910.
NOTE 2—CQS-1h is used for quick-set slurry seal systems.
Rapid-Setting Medium-Setting Slow-Setting Quick-Setting
Type CRS-1 CRS-2 CMS-2 CMS-2h CSS-1 CSS-1h CQS-1h
Grade min max min max min max min max min max min max min max
Test on Emulsions:
Viscosity, Saybolt Furol at 25 °C (77 °F) SFS 20 100 20 100 20 100
Viscosity, Saybolt Furol at 50 °C
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D2397/D2397M − 13 D2397/D2397M − 17
Standard Specification for
1
Cationic Emulsified Asphalt
This standard is issued under the fixed designation D2397/D2397M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers seven grades of cationic emulsified asphalt for use in pavement construction in the manner
designated.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D5D5/D5M Test Method for Penetration of Bituminous Materials
3
D113 Test Method for Ductility of Bituminous Materials (Withdrawn 2016)
D140D140/D140M Practice for Sampling BituminousAsphalt Materials
D244 Test Methods and Practices for Emulsified Asphalts
D2042 Test Method for Solubility of Asphalt Materials in Trichloroethylene
D3910 Practices for Design, Testing, and Construction of Slurry Seal
D6930 Test Method for Settlement and Storage Stability of Emulsified Asphalts
D6933 Test Method for Oversized Particles in Emulsified Asphalts (Sieve Test)
D6935 Test Method for Determining Cement Mixing of Emulsified Asphalt
D6936 Test Method for Determining Demulsibility of Emulsified Asphalt
D6997 Test Method for Distillation of Emulsified Asphalt
D7226 Test Method for Determining the Viscosity of Emulsified Asphalts Using a Rotational Paddle Viscometer
D7402 Practice for Identifying Cationic Emulsified Asphalts
D7496 Test Method for Viscosity of Emulsified Asphalt by Saybolt Furol Viscometer
D7553 Test Method for Solubility of Asphalt Materials in N-Propyl Bromide
3. Requirements
3.1 The emulsified asphalt shall be tested within 14 days of delivery. The emulsified asphalt shall be homogeneous after
thorough mixing provided separation has not been caused by freezing. Emulsions separated by freezing shall not be tested.
3.2 Emulsified asphalt shall conform to the requirements prescribed in Table 1 or Table 2. If no table is specified, the default
isSpecify the test method Table 1to be used. Specify either Test Method D7226 or D7496.
4. Sampling
4.1 Samples of emulsified asphalt shall be taken in accordance with Practice D140D140/D140M.
1
This specification is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.41 on Emulsified
Asphalt Specifications.
Current edition approved Dec. 1, 2013June 1, 2017. Published January 2014June 2017. Originally approved in 1965. Last previous edition approved in 20122013 as
D2397 – 12.D2397/D2397M – 13. DOI: 10.1520/D2397_D2397M-13.10.1520/D2397_D2397M-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D2397/D2397M − 17
2
TABLE 1 Requirements for Cationic Emulsified Asphalt
Type Rapid-Setting Medium-Setting Slow-Setting Quick Setting
A
CRS-1 CRS-2 CMS-2 CMS-2h CSS-1 CSS-1h CQS-1h
Grade
min max min max min max min max min max min max min max
Test on emulsions:
Viscosity, Saybolt Furol at 25°C [77°F] SFS 20 100 20 100 20 100
Viscosity, Saybolt Furol at 50°C [122°F] SFS 20 100 100 400 50 450 50 450
B
Storage stability test, 24-h, % 1 1 1 1 1 1
Demulsibility, 35 mL, 0.8 % dioctyl sodium 40 . 40 .
sulfosuccinate, %
Coating ability and water resistance:
Coating, dry aggregate good
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.