ASTM C140/C140M-20a
(Test Method)Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
SIGNIFICANCE AND USE
4.1 These test methods provide general testing requirements for application to a broad range of concrete products. Those general testing requirements are included in the body of this standard.
Note 2: Consult manufacturer, supplier, product specifications, or other resources for more specific measurement or testing guidelines for those products not addressed with the annex of this standard.
4.2 These test methods provide specific testing requirements in two distinct sections, the requirements applicable to all units covered by these test methods and those applicable to the specific unit types. The requirements applicable to all units are included in the body of these test methods and those applicable to the specific unit types are included within the annexes.
SCOPE
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength, absorption, unit weight (density), moisture content, flexural load, and ballast weight. Not all methods are applicable to all unit types, however.
1.2 Specific testing and reporting procedures are included in annexes to these test methods for the following specific unit types:
Annex A1—Concrete masonry units
(Specifications C90, C129)
Annex A2—Concrete and calcium silicate brick
(Specifications C55, C73, C1634)
Annex A3—Segmental retaining wall units (Specification C1372)
Annex A4—Concrete interlocking paving units
(Specification C936/C936M)
Annex A5—Concrete grid paving units (Specification C1319)
Annex A6—Concrete roof pavers
(Specification C1491)
Annex A7—Dry-cast articulating concrete block
(Specification D6684)
Annex A8—Segmental Concrete Paving Slabs
(Specification C1782/C1782M)
1.3 The test procedures included in these test methods are also applicable to other types of units not referenced in these test methods, but specific testing and reporting requirements for those units are not included.
1.4 These test methods include the following sections:
Section
Scope
1
Referenced Documents
2
Terminology
3
Significance and Use
4
Sampling
5
Measurement of Dimensions
6
Compressive Strength
7
Absorption
8
Calculations
9
Report
10
Keywords
11
Annexes—Test Procedures
Concrete Masonry Units
Annex A1
Concrete and Calcium Silicate Brick
Annex A2
Segmental Retaining
Wall Units
Annex A3
Concrete Interlocking Paving Units
Annex A4
Concrete Grid Paving
Units
Annex A5
Concrete Roof Pavers
Annex A6
Dry-Cast Articulating
Concrete Block
Annex A7
Segmental Concrete Paving Slabs
Annex A8
Worksheet and Test Report for
Concrete Masonry Units
Appendix X1
Note 1: The testing laboratory performing these test methods should be evaluated in accordance with Practice C1093.
1.5 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accordanc...
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C140/C140M − 20a
Standard Test Methods for
Sampling and Testing Concrete Masonry Units and Related
1
Units
This standard is issued under the fixed designation C140/C140M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
Section
Measurement of Dimensions 6
1.1 These test methods provide various testing procedures
Compressive Strength 7
commonly used for evaluating characteristics of concrete Absorption 8
Calculations 9
masonryunitsandrelatedconcreteunits.Methodsareprovided
Report 10
for sampling, measurement of dimensions, compressive
Keywords 11
strength, absorption, unit weight (density), moisture content, Annexes—Test Procedures
Concrete Masonry Units Annex A1
flexural load, and ballast weight. Not all methods are appli-
Concrete and Calcium Silicate Brick Annex A2
cable to all unit types, however.
Segmental Retaining Annex A3
Wall Units
1.2 Specifictestingandreportingproceduresareincludedin
Concrete Interlocking Paving Units Annex A4
annexes to these test methods for the following specific unit
Concrete Grid Paving Annex A5
Units
types:
Concrete Roof Pavers Annex A6
Annex A1—Concrete masonry units
Dry-Cast Articulating Annex A7
(Specifications C90, C129)
Concrete Block
Annex A2—Concrete and calcium silicate brick
Segmental Concrete Paving Slabs Annex A8
(Specifications C55, C73, C1634)
Worksheet and Test Report for Appendix X1
Annex A3—Segmental retaining wall units (Specification C1372)
Concrete Masonry Units
Annex A4—Concrete interlocking paving units
NOTE 1—The testing laboratory performing these test methods should
(Specification C936/C936M)
be evaluated in accordance with Practice C1093.
Annex A5—Concrete grid paving units (Specification C1319)
Annex A6—Concrete roof pavers
1.5 The text of this test method references notes and
(Specification C1491)
footnotes that provide explanatory material. These notes and
Annex A7—Dry-cast articulating concrete block
(Specification D6684)
footnotes (excluding those in tables and figures) shall not be
Annex A8—Segmental Concrete Paving Slabs
considered as requirements of the standard.
(Specification C1782/C1782M)
1.6 The values stated in either SI units or inch-pound units
1.3 The test procedures included in these test methods are
are to be regarded separately as standard. The values stated in
also applicable to other types of units not referenced in these
each system may not be exact equivalents; therefore, each
test methods, but specific testing and reporting requirements
system shall be used independently of the other. Combining
for those units are not included.
values from the two systems may result in non-conformance
1.4 These test methods include the following sections:
with the standard.
Section
1.7 This standard does not purport to address all of the
Scope 1
Referenced Documents 2 safety concerns, if any, associated with its use. It is the
Terminology 3
responsibility of the user of this standard to establish appro-
Significance and Use 4
priate safety, health, and environmental practices and deter-
Sampling 5
mine the applicability of regulatory limitations prior to use.
1.8 This international standard was developed in accor-
1
dance with internationally recognized principles on standard-
These test methods are under the jurisdiction of ASTM Committee C15 on
Manufactured Masonry Units and are the direct responsibility of Subcommittee
ization established in the Decision on Principles for the
C15.03 on Concrete Masonry Units and Related Units.
Development of International Standards, Guides and Recom-
Current edition approved June 1, 2020. Published June 2020. Originally
mendations issued by the World Trade Organization Technical
approved in 1938. Last previous edition approved in 2020 as C140/C140M–20.
DOI: 10.1520/C0140_C0140M-20A. Barriers to Trade (TBT) Committee.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C140/C140M − 20a
NOTE 2—Consult manufacturer, supplier, product specifications, or
2. Referenced Documents
other resources for more specific measurement or testing guidelines for
2
2.1 ASTM Standards:
those products not addressed with the annex of this standard.
C55Specification for Concrete Building Brick
4.2 Thesetestmethodsprovidespecifictestingrequirements
C73Specification for Calcium Silicate Brick (Sand-Lime
intwodistinctsections,therequirementsapplicablet
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C140/C140M − 20 C140/C140M − 20a
Standard Test Methods for
Sampling and Testing Concrete Masonry Units and Related
1
Units
This standard is issued under the fixed designation C140/C140M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry
units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength,
absorption, unit weight (density), moisture content, flexural load, and ballast weight. Not all methods are applicable to all unit
types, however.
1.2 Specific testing and reporting procedures are included in annexes to these test methods for the following specific unit types:
Annex A1—Concrete masonry units
(Specifications C90, C129)
Annex A2—Concrete and calcium silicate brick
(Specifications C55, C73, C1634)
Annex A3—Segmental retaining wall units (Specification C1372)
Annex A4—Concrete interlocking paving units
(Specification C936/C936M)
Annex A5—Concrete grid paving units (Specification C1319)
Annex A6—Concrete roof pavers
(Specification C1491)
Annex A7—Dry-cast articulating concrete block
(Specification D6684)
Annex A8—Segmental Concrete Paving Slabs
(Specification C1782/C1782M)
1.3 The test procedures included in these test methods are also applicable to other types of units not referenced in these test
methods, but specific testing and reporting requirements for those units are not included.
1.4 These test methods include the following sections:
Section
Scope 1
Referenced Documents 2
Terminology 3
Significance and Use 4
Sampling 5
Measurement of Dimensions 6
Compressive Strength 7
Absorption 8
Calculations 9
Report 10
Keywords 11
Annexes—Test Procedures
Concrete Masonry Units Annex A1
Concrete and Calcium Silicate Brick Annex A2
Segmental Retaining Annex A3
Wall Units
Concrete Interlocking Paving Units Annex A4
Concrete Grid Paving Annex A5
Units
Concrete Roof Pavers Annex A6
1
These test methods are under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and are the direct responsibility of Subcommittee C15.03 on
Concrete Masonry Units and Related Units.
Current edition approved Feb. 1, 2020June 1, 2020. Published February 2020June 2020. Originally approved in 1938. Last previous edition approved in 20182020 as
C140 – 18a.C140/C140M – 20. DOI: 10.1520/C0140_C0140M-20.10.1520/C0140_C0140M-20A.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C140/C140M − 20a
Section
Dry-Cast Articulating Annex A7
Concrete Block
Segmental Concrete Paving Slabs Annex A8
Worksheet and Test Report for Appendix X1
Concrete Masonry Units
NOTE 1—The testing laboratory performing these test methods should be evaluated in accordance with Practice C1093.
1.5 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the standard.
1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.8 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C55 Specification for Concrete Bu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.