ASTM C317/C317M-00(2015)
(Specification)Standard Specification for Gypsum Concrete
Standard Specification for Gypsum Concrete
ABSTRACT
This specification covers mill-mixed gypsum concrete, consisting essentially of calcined gypsum and suitable aggregate, requiring the addition of water only at the job site. Gypsum concrete is intended for use in the construction of poured-in-place roof decks or slabs. Two classes, based on the compressive strength and density, are covered. Gypsum concrete shall consist of calcined gypsum to which are added aggregates, wood chips, or wood shavings in proportion to meet the applicable requirements of this specification. Test method in this specification shall be performed in order to determine the physical properties of the gypsum concrete. Setting time is determined by the Vicat method.
SCOPE
1.1 This specification covers mill-mixed gypsum concrete, consisting essentially of calcined gypsum and suitable aggregate, requiring the addition of water only at the job site. Gypsum concrete is intended for use in the construction of poured-in-place roof decks or slabs. Two classes, based on the compressive strength and density, are covered.
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C317/C317M −00 (Reapproved 2015)
Standard Specification for
Gypsum Concrete
This standard is issued under the fixed designation C317/C317M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 4.2 Calcined Gypsum—Specification C28/C28M.
1.1 This specification covers mill-mixed gypsum concrete, 4.3 Aggregates—Specification C35.
consisting essentially of calcined gypsum and suitable
4.4 Wood Chips or Wood Shavings, shall be dry wood,
aggregate, requiring the addition of water only at the job site.
uniform and clean in appearance, passing a 1-in. [25-mm]
Gypsum concrete is intended for use in the construction of
sieve, and not more than ⁄16 in. [1.5 mm] thick.
poured-in-place roof decks or slabs. Two classes, based on the
compressive strength and density, are covered.
5. Physical Properties
1.2 The values stated in either inch-pound units or SI units
5.1 SettingTime—Gypsum concrete shall set in not less than
are to be regarded separately as standard. The values stated in
20 min and not more than 90 min.
each system may not be exact equivalents; therefore, each
5.2 Compressive Strength—Gypsum concrete shall have the
system shall be used independently of the other. Combining
following compressive strength for the respective classes:
values from the two systems may result in nonconformance
with the standard.
Class Compressive Strength, min,
psi [MPa]
2. Referenced Documents
A 500 [3.5]
B 1000 [7.0]
2.1 ASTM Standards:
C11 Terminology Relating to Gypsum and Related Building
Materials and Systems
C28/C28M Specification for Gypsum Plasters 5.3 Density—Gypsum concrete, Class A, shall have a den-
3 3
C35 Specification for Inorganic Aggregates for Use in Gyp-
sity of not more than 60 lb/ft [960 kg/m ].
sum Plaster
6. Sampling
C472 Test Methods for Physical Testing of Gypsum, Gyp-
sum Plasters and Gypsum Concrete
6.1 Randomly select at least 1 % of the packages, but not
less than five packages. Take samples from both the outer
3. Terminology
portion and the center of each package. Mix the samples so
3.1 Definitions of terms shall be in accordance with Termi-
obtained to provide a composite sample of not less than 15 lb
nology C11.
[6.5 kg]. Immediately place the sample in a clean, dry, airtight
container for delivery to the laboratory.
4. Materials and Manufacture
7. Test Methods
4.1 Gypsum concrete shall consist of calcined gypsum to
which is added aggregates, wood chips, or wood shavings in
7.1 Determinethephysicalpropertiesofgypsumconcretein
proportion to meet the applicable requirements of this specifi-
accordance with Test Methods C472.
cation.
7.1.1 Determine the setting time by the Vicat method.
8. Inspection
This specification is under the jurisdiction of ASTM Committee C11 on
Gypsum and Related Building Materials and Systemsand is the direct responsibility
8.1 Inspection of the g
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C317/C317M − 00 (Reapproved 2010) C317/C317M − 00 (Reapproved 2015)
Standard Specification for
Gypsum Concrete
This standard is issued under the fixed designation C317/C317M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers mill-mixed gypsum concrete, consisting essentially of calcined gypsum and suitable aggregate,
requiring the addition of water only at the job site. Gypsum concrete is intended for use in the construction of poured-in-place roof
decks or slabs. Two classes, based on the compressive strength and density, are covered.
1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in nonconformance with the standard.
2. Referenced Documents
2.1 ASTM Standards:
C11 Terminology Relating to Gypsum and Related Building Materials and Systems
C28/C28M Specification for Gypsum Plasters
C35 Specification for Inorganic Aggregates for Use in Gypsum Plaster
C472 Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete
3. Terminology
3.1 Definitions of terms shall be in accordance with Terminology C11.
4. Materials and Manufacture
4.1 Gypsum concrete shall consist of calcined gypsum to which is added aggregates, wood chips, or wood shavings in
proportion to meet the applicable requirements of this specification.
4.2 Calcined Gypsum—Specification C28/C28M.
4.3 Aggregates—Specification C35.
4.4 Wood Chips or Wood Shavings, shall be dry wood, uniform and clean in appearance, passing a 1-in. [25-mm] sieve, and not
more than ⁄16 in. [1.5 mm] thick.
5. Physical Properties
5.1 Setting Time—Gypsum concrete shall set in not less than 20 min and not more than 90 min.
5.2 Compressive Strength—Gypsum concrete shall have the following compressive strength for the respective classes:
Class Compressive Strength, min,
psi [MPa]
A 500 [3.5]
B 1000 [7.0]
This specification is under the jurisdiction of ASTM Committee C11 on Gypsum and Related Building Materials and Systemsand is the direct responsibility of
Subcommittee C11.01 on Specifications and Test Methods for Gypsum Products.
Current edition approved Oct. 1, 2010Oct. 1, 2015. Published December 2010October 2015. Originally approved in 1953. Last previous edition approved in 20002010
as C317 – 00C317(2005). – 00 (2010). DOI: 10.1520/C0317_C0317M-00R10.10.1520/C0317_C0317M-00R15.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document S
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.