ASTM A304-05e1

Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements

SCOPE
1.1 This specification covers hot-worked alloy, carbon, and carbon-boron steels in a variety of compositions and sizes, which may attain specified depth of hardening in the end quench test. These steel compositions are identified by the suffix letter "H" added to the conventional grade number.
1.2 This specification provides for analyses other than those listed under Tables 1 and 2. Special hardenability limits are also permissible when approved by the purchaser and manufacturer.
1.3 The values stated in inch-pound units are to be regarded as the standard.

General Information

• Status: Historical
• Publication Date: 28-Feb-2005
• ICS: 77.140.60 - Steel bars and rods
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.15 - Bars

Relations

• Replaces: ASTM A304-05 - Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements
• Effective Date: 01-Mar-2005
• Replaced By: ASTM A304-05e2 - Standard Specification for Carbon and Alloy Steel Bars Subject to End-Quench Hardenability Requirements
• Effective Date: 01-Mar-2005
• Referred By: ASTM A108-18 - Standard Specification for Steel Bar, Carbon and Alloy, Cold-Finished
• Effective Date: 01-Mar-2005
• Referred By: ASTM A400-17 - Standard Practice for Steel Bars, Selection Guide, Composition, and Mechanical Properties
• Effective Date: 01-Mar-2005
• Referred By: ASTM A689-97(2018) - Standard Specification for Carbon and Alloy Steel Bars for Springs
• Effective Date: 01-Mar-2005
• Referred By: ASTM A914/A914M-19 - Standard Specification for Steel Bars Subject to Restricted End-Quench Hardenability Requirements
• Effective Date: 01-Mar-2005
• Referred By: ASTM D5977-23 - Standard Specification for High Load Rotational Spherical Bearings for Bridges and Structures
• Effective Date: 01-Mar-2005
• Referred By: ASTM A322-13(2018)e1 - Standard Specification for Steel Bars, Alloy, Standard Grades
• Effective Date: 01-Mar-2005
• Referred By: ASTM A534-17(2022) - Standard Specification for Carburizing Steels for Anti-Friction Bearings
• Effective Date: 01-Mar-2005
• Referred By: ASTM A29/A29M-23 - Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought
• Effective Date: 01-Mar-2005

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
An American National Standard
e1
Designation: A 304 – 05
Standard Specification for
Carbon and Alloy Steel Bars Subject to End-Quench
1
Hardenability Requirements
This standard is issued under the fixed designation A 304; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1
e NOTE—Editorial changes made to text and Figure 18 in July 2005.
1. Scope* 3.1.1 hardenability—the relative ability of a steel to harden
under heat treatment becomes apparent in the degree to which
1.1 This specification covers hot-worked alloy, carbon, and
the material hardens when quenched at different cooling rates.
carbon-boron steels in a variety of compositions and sizes,
It is measured quantitatively, usually by noting the extent or
which may attain specified depth of hardening in the end
depth of hardening of a standard size and shape test specimen
quench test. These steel compositions are identified by the
in a standardized quench. In the “end-quench” test the “depth
suffix letter “H” added to the conventional grade number.
of hardening” is the distance along the specimen from the
1.2 This specification provides for analyses other than those
quenched end to a given hardness.
listed under Tables 1 and 2. Special hardenability limits are
also permissible when approved by the purchaser and manu-
4. Ordering Information
facturer.
4.1 Orders for material under this specification should
1.3 The values stated in inch-pound units are to be regarded
include the following information, in proper sequence:
as the standard.
4.1.1 Quantity (weight),
2. Referenced Documents 4.1.2 Name of material (alloy, carbon, or carbon-boron
2
steel),
2.1 ASTM Standards:
4.1.3 Cross-sectional shape,
A 29/A 29M SpecificationforSteelBars,CarbonandAlloy,
4.1.4 Size,
Hot-Wrought, General Requirements for
4.1.5 Length,
A 108 Specification for Steel Bar, Carbon and Alloy, Cold-
4.1.6 Grade,
Finished
4.1.7 End-quenched hardenability (see Section 9),
A 255 Test Method for Determining Hardenability of Steel
4.1.8 Report of heat analysis, if desired (see Section 7),
E112 Test Methods for Determining Average Grain Size
4.1.9 Special straightness, if required,
E 527 Practice for Numbering Metals and Alloys (UNS)
4.1.10 ASTM designation and date of issue,
3. Terminology 4.1.11 End use or special requirements, and
4.1.12 Leaded steel, when required.
3.1 Definitions of Terms Specific to This Standard:
NOTE 1—A typical ordering description is as follows: 10 000 lb, alloy
6
bars, round, 4.0 in. dia by 10 ft, Grade 1340H, J 40/56 = ⁄16 in., heat
1
analysis required, ASTM A 304, dated ________, worm gear.
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel, and RelatedAlloys and is the direct responsibility of Subcommittee
4.2 The purchaser shall specify the desired grade, including
A01.15 on Bars.
the suffix letter “H,” in accordance with Table 1 or Table 2.
Current edition approved March 1, 2005. Published March 2005. Originally
approved in 1947. Last previous edition approved in 2004 as A 304 – 04.
4.3 Band limits are shown graphically and as tabulations in
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Figs. 2-87, inclusive. For specifications purposes, the tabulated
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
values of Rockwell C hardness are used. Values below 20
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. Rockwell C hardness (20 HRC) are not specified because such
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn. Contact ASTM
International (www.astm.org) for the latest information.
e1
A304–05
values are below the normal range of the C scale. The graphs 6. General Requirements
are shown for convenience in estimating the hardness values
6.1 Material furnished under this specification shall con-
obtainable at various locations on the end quench test bar and
form to the applicable requirements of the current edition of
for various locations in oil or water quenched rounds. The
SpecificationA 29/A 29M orA 108, unless otherwise provided
relationship between end-quench distance and bar diameter is
for in this specification.
approximate and should be used only as a guide.
...