iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F2460-06

(Practice)

Standard Practice for Special Requirements for Bumper Boats

Standard Practice for Special Requirements for Bumper Boats

SCOPE
1.1 This practice establishes criteria for the design, manufacture, and operations of bumper boats. These are boats used to bump into each other intentionally as directed by drivers as a form of entertainment. Boats are fitted with an inflatable or impact attenuating device to allow for such bumping.
1.2 This practice follows Practices F 1193 and F 770 as the basic level of safety for bumper boats. These practices shall be followed for all bumper boats under this practice. This practice shall include all modifications, improvements, and deviations to design, quality, manufacture, construction, ownership, operation, inspection, and maintenance of a bumper boat
1.3 This practice does not apply to personal watercraft, human powered watercraft, or watercraft used for general purposes by private owners.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
14-Oct-2006
ICS
47.080 - Small craft
Technical Committee
F24 - Amusement Rides and Devices
Drafting Committee
F24.60 - Special Rides/Attractions
Current Stage
Ref Project

Relations

Replaced By
ASTM F2460-07 - Standard Practice for Special Requirements for Bumper Boats
Effective Date
15-Nov-2007
Referred By
ASTM F2783-20 - Standard Practice for Design, Manufacture, Operation, Maintenance, and Inspection of Amusement Rides and Devices, in Canada
Effective Date
15-Oct-2006

Buy Standard

ASTM F2460-06 - Standard Practice for Special Requirements for Bumper BoatsASTM F2460-06 - Standard Practice for Special Requirements for Bumper Boats
PreviousNext
Standard
ASTM F2460-06 - Standard Practice for Special Requirements for Bumper Boats
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F2460–06
Standard Practice for
Special Requirements for Bumper Boats
This standard is issued under the fixed designation F 2460; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 NFPA Standards:
National Fire and Protection Association Standards
1.1 This practice establishes criteria for the design, manu-
facture, and operations of bumper boats. These are boats used
3. Significance and Use
to bump into each other intentionally as directed by drivers as
3.1 The purpose of this practice is to delineate information
a form of entertainment. Boats are fitted with an inflatable or
and to establish procedures for the operation of a bumper boat
impact attenuating device to allow for such bumping.
amusement ride.
1.2 This practice follows Practices F 1193 and F 770 as the
3.2 The device is a single craft, unattached to other craft or
basic level of safety for bumper boats. These practices shall be
common frame system. It is non-human powered without
followed for all bumper boats under this practice. This practice
connection to a common energy source. It is driver controlled
shall include all modifications, improvements, and deviations
with respect to acceleration, speed, and steering.
to design, quality, manufacture, construction, ownership, op-
eration, inspection, and maintenance of a bumper boat
4. Design Requirements
1.3 This practice does not apply to personal watercraft,
4.1 Throttle/power controls shall return automatically to
human powered watercraft, or watercraft used for general
stop or slow speed when released.
purposes by private owners.
4.2 All battery powered units will provide adequate venti-
1.4 This standard does not purport to address all of the
lation to battery compartment.
safety concerns, if any, associated with its use. It is the
4.3 Any moving drive component (that is, propellers, im-
responsibility of the user of this standard to establish appro-
pellers) must be guarded on all sides, whenever ride is in
priate safety and health practices and determine the applica-
operation. Openings of the guard shall be no larger in diameter
bility of regulatory limitations prior to use.
or width than 0.625 in. (15.87 mm).
2. Referenced Documents 4.4 Throttle/power controls shall be located in such a
2 manner as to prevent accidental activation during loading or
2.1 ASTM Standards:
unloading of boat.
F 770 Practice for Ownership and Operation ofAmusement
Rides and Devices
5. Quality, Manufacture, and Construction Requirements
F 853 Practice for Maintenance Procedures for Amusement
5.1 Quality, manufacture, and construction shall be in ac-
Rides and Devices
cordance with in Practices F 1193 and F 1159.
F 1159 Practice for Design and Manufacture of Patron
Directed, Artificial Climbing Walls, Dry Slide, Coin Oper-
6. Ownership and Operation Requirements
ated and Purposeful Water Immersion Amusement Rides
6.1 Ownership and operation requirements for this practice
and Devices and Air-Supported Structures
are outlined in Practice F 770. The items below are require-
F 1193 Practice for Quality, Manufacture, and Construction
ments in addition to Practice F 770.
of Amusement Rides and Devices
6.2 Bumper boats may be equipped with heat shields and
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F2460-19(Practice)
Standard Practice for Special Requirements for Bumper Boats

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to delineate information and to establish procedures for the operation of a bumper boat amusement ride.  
3.2 The device is a single craft, unattached to other craft or common frame system. It is non-human powered without connection to a common energy source. It is driver controlled with respect to acceleration, speed, and steering.
SCOPE
1.1 This practice establishes criteria for the design, manufacture, and operations of bumper boats. These are boats used to bump into each other intentionally as directed by drivers as a form of entertainment. Boats are fitted with an inflatable or impact attenuating device to allow for such bumping.  
1.2 This practice follows Practices F1193 and F770 as the basic level of safety for bumper boats. These practices shall be followed for all bumper boats under this practice. This practice shall include all modifications, improvements, and deviations to design, quality, manufacture, construction, ownership, operation, inspection, and maintenance of a bumper boat  
1.3 This practice does not apply to personal watercraft, human powered watercraft, or watercraft used for general purposes by private owners.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1739-96(2024)(Guide)
Standard Guide for Performance of a Water Rescuer—Level I

SIGNIFICANCE AND USE
4.1 The purpose of this guide is to establish a minimum level of knowledge and skills for the water rescue responder. The application will improve the quality of initial emergency response, the rescue of the water victims, and the safety of the rescuers.  
4.2 All persons who are identified as water rescuers and water rescue responders shall meet the requirements of this guide.  
4.3 This guide does not preclude the scope of performances for water rescuers needing more advanced or more specialized water rescue training.  
4.4 This guide will assist government agencies; state, local, or regional organizations; fire departments; rescue teams; and others who are responsible for establishing a minimum performance for personnel who respond to water emergencies.
SCOPE
1.1 This guide covers minimum requirements for the scope of performance of a water rescuer I who may be responsible for the initial on-scene evaluation, performing land-based water rescues, and providing initial patient care at a water rescue incident.  
1.2 This guide is one in a series; water rescuer I is only a beginning level designed for a water rescue responder. Duties and responsibilities at water rescue operations vary according to the water rescuer's skills and knowledge. As the water rescuer level I progresses and becomes more proficient, the individual will move from responder to in-water rescuer to rescue boat operator.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    3 pages
    English language
    sale 15% off
ASTM
ASTM F1018-22(Specification)
Standard Specification for Steel Emergency Gear Stowage Locker

ABSTRACT
This specification establishes the material and design requirements, as well as the mandatory dimensional and construction details for four types of steel emergency gear stowage lockers used for the stowage of one or two complete fireman's outfit(s).
SCOPE
1.1 This specification covers the design, material, and manufacture of steel emergency gear stowage lockers.  
1.2 Emergency gear lockers shall be of four types (see Section 3).  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    11 pages
    English language
    sale 15% off
  • Technical specification
    11 pages
    English language
    sale 15% off
ASTM
ASTM F1729-96(2020)(Practice)
Standard Practice for Single Person Cold Water Survival/Rescue Technique: HELP Position

SIGNIFICANCE AND USE
3.1 This practice establishes a single person cold water survival/rescue procedure.  
3.2 All persons who are identified as water rescuers shall meet the requirements of this practice.  
3.3 This practice is intended to assist government agencies, state, local, or regional organizations; fire departments; and rescue teams and others who are responsible for establishing a minimum performance for personnel who respond to water emergencies.  
3.4 A rescuer needs to be wearing a personal flotation device to perform this technique. These devices should conform to standards set by the appropriate national regulatory authority, that is, the U.S. Coast Guard in the United States, and be in good and serviceable condition.  
3.5 A water rescuer sometimes may be immersed in cold water for prolonged periods of time. They are unable to get to shore or shore is too far away, rescue is not imminent, no boat is available to get into or on top of, and no flotsam is available. The water rescuer needs to assume a defensive posture to conserve heat and increase survival time.
SCOPE
1.1 This practice covers the recommended water rescue procedure for performing the heat escape lessening posture (HELP) position.  
1.2 This practice is one in a set of self-rescue techniques for the water rescuer.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1730-96(2020)(Guide)
Standard Guide for Throwing a Water Rescue Throwbag

SIGNIFICANCE AND USE
3.1 This guide establishes a recommended procedure for a throwing rescue to ensure the safety of all water rescuers who may be involved in rescue techniques at a water rescue emergency.  
3.2 This water rescue technique can be utilized from land, boat, or any stable platform.  
3.3 All persons who are identified as water rescuers shall meet the requirements of this guide.  
3.4 This guide is intended to assist government agencies, state, local, and regional organizations; fire departments; rescue teams and others who are responsible for establishing a minimum performance for personnel who respond to water emergencies.  
3.5 The procedure outlined in the document may vary with the number and type of victims, and water conditions.
SCOPE
1.1 This guide covers the recommended procedures for throwing a water rescue throwbag.  
1.2 This guide is one in a series of water rescue techniques for the water rescuer.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1728-96(2020)(Practice)
Standard Practice for Multiple Persons Cold Water Survival/Rescue Technique: Huddle Position

SIGNIFICANCE AND USE
3.1 This practice establishes a multiple person cold water survival/rescue procedure.  
3.2 All persons who are identified as water rescuers shall meet the requirements of this practice.  
3.3 This practice is intended to assist government agencies, state, local, or regional organizations; fire departments; and rescue teams and others who are responsible for establishing a minimum performance for personnel who respond to water emergencies.  
3.4 The majority of the rescuers performing this technique must be wearing personal flotation devices. These devices should conform to standards set by the appropriate national regulatory authority, that is, the U.S. Coast Guard in the United States, and be in good and serviceable condition.  
3.5 A water rescuer sometimes may be immersed in cold water for prolonged periods of time. They are unable to get to shore or shore is too far away, rescue is not imminent, no boat is available to get into or on top of, and no flotsam is available. The water rescuer needs to assume a defensive posture to conserve heat and increase survival time.
SCOPE
1.1 This practice covers the recommended water rescue procedure for performing the huddle position.  
1.2 This practice is one in a set of self-rescue techniques for the water rescuer.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F3052-14(2020)e1(Guide)
Standard Guide for Conducting Small Boat Stability Test (Deadweight Survey and Air Inclining Experiment) to Determine Lightcraft Weight and Centers of Gravity of a Small Craft

SIGNIFICANCE AND USE
4.1 From the lightcraft characteristics, calculations of the stability characteristics of the small craft for all load conditions can determine compliance to applicable stability criteria or provide mass properties information for other analyses or investigations. Accurate results from an air incline stability test may therefore determine future survival of the boat, the crew and compliment. If the small craft is not 100 % complete or there is fuel or other liquids in a tank that is supposed to be clean and dry then the person leading the stability test must determine the acceptability of all variances from the guide based on the ability to correct for these variances analytically. A complete understanding of the principles behind the stability test and knowledge of the factors that affect the results is therefore necessary.  
4.2 The results of the stability test typically supersede the corresponding values in the weight estimate for any subsequent use in ascertaining compliance to stability or weight control criteria and may be used in weight margin adjudication.
SCOPE
1.1 This guide covers the determination of a small boat’s lightcraft characteristics. The air incline stability test can be considered two separate tasks; a deadweight survey and an air-inclining experiment. The stability test is recommended, but not required, for all small craft upon their construction completion or after major conversions, or both, where stability information is required. It is typically conducted indoors and an enclosed facility to protect the vessels from unprotected environmental conditions.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    20 pages
    English language
    sale 15% off
ASTM
ASTM F2460-19(Practice)
Standard Practice for Special Requirements for Bumper Boats

SIGNIFICANCE AND USE
3.1 The purpose of this practice is to delineate information and to establish procedures for the operation of a bumper boat amusement ride.  
3.2 The device is a single craft, unattached to other craft or common frame system. It is non-human powered without connection to a common energy source. It is driver controlled with respect to acceleration, speed, and steering.
SCOPE
1.1 This practice establishes criteria for the design, manufacture, and operations of bumper boats. These are boats used to bump into each other intentionally as directed by drivers as a form of entertainment. Boats are fitted with an inflatable or impact attenuating device to allow for such bumping.  
1.2 This practice follows Practices F1193 and F770 as the basic level of safety for bumper boats. These practices shall be followed for all bumper boats under this practice. This practice shall include all modifications, improvements, and deviations to design, quality, manufacture, construction, ownership, operation, inspection, and maintenance of a bumper boat  
1.3 This practice does not apply to personal watercraft, human powered watercraft, or watercraft used for general purposes by private owners.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F1003-19(Specification)
Standard Specification for Searchlights on Motor Lifeboats

ABSTRACT
This specification covers searchlights for motor lifeboats. Searchlights shall be of sturdy construction, and free from mechanical, electrical, or other imperfections or defects which materially affect appearance or which may affect quality, reliability, or serviceability. Watertightness test, operational test, impact test, light projection test, and switch endurance test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers searchlights for motor lifeboats. This specification is incorporated in U.S. Coast Guard Regulation 46 CFR 199.175 for survival craft and rescue equipment.  
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM D88/D88M-07(2024)(Test Method)
Standard Test Method for Saybolt Viscosity

SIGNIFICANCE AND USE
5.1 This test method is useful in characterizing certain petroleum products, as one element in establishing uniformity of shipments and sources of supply.  
5.2 See Guide D117 for applicability to mineral oils used as electrical insulating oils.  
5.3 The Saybolt Furol viscosity is approximately one tenth the Saybolt Universal viscosity, and is recommended for characterization of petroleum products such as fuel oils and other residual materials having Saybolt Universal viscosities greater than 1000 s.  
5.4 Determination of the Saybolt Furol viscosity of bituminous materials at higher temperatures is covered by Test Method E102/E102M.
SCOPE
1.1 This test method covers the empirical procedures for determining the Saybolt Universal or Saybolt Furol viscosities of petroleum products at specified temperatures between 21 and 99 °C [70 and 210 °F]. A special procedure for waxy products is indicated.  
Note 1: Test Methods D445 and D2170/D2170M are preferred for the determination of kinematic viscosity. They require smaller samples and less time, and provide greater accuracy. Kinematic viscosities may be converted to Saybolt viscosities by use of the tables in Practice D2161. It is recommended that viscosity indexes be calculated from kinematic rather than Saybolt viscosities.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off