ASTM F289-96(2014)

Standard Specification for Molybdenum Wire and Rod for Electronic Applications

ABSTRACT
This specification deals with molybdenum wire and rod for electronic applications. The following grades of molybdenum wire and rod are covered in this specification: Grade 1—commercially pure molybdenum wire suitable for leads, hooks, supports, heaters, and metal-to-glass seals; Grade 2—commercially pure molybdenum wire suitable for mandrel either black or cleaned; and Grade 3—commercially pure molybdenum rod suitable for leads, hooks, supports, and metal-to-glass seals. Materials shall be tested and the individual grades shall conform to specified values of chemical composition, minimum tensile strength, elongation, ductility, surface finish, dimensional tolerances, and straightness.
SCOPE
1.1 This specification covers two grades of molybdenum wire less than 0.050 in. (1.27 mm) in diameter and one grade of molybdenum rod 1.00 in. (25.4 mm) or less in diameter as follows:  
1.1.1 Grade 1—Commercially pure molybdenum wire suitable for leads, hooks, supports, heaters, and metal-to-glass seals.  
1.1.2 Grade 2—Commercially pure molybdenum wire suitable for mandrel either black or cleaned.  
1.1.3 Grade 3—Commercially pure molybdenum rod suitable for leads, hooks, supports, and metal-to-glass seals.  
1.2 The term wire applies to all spooled or coiled material and 0.050 in. (1.3 mm) or less in diameter and to short cut lengths 0.020 in. (0.51 mm) or less in diameter.  
1.3 The term rod applies to all material over 0.020 in. (0.51 mm) in diameter, supplied in straight lengths.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 31-May-2014
• ICS: 29.060.10 - Wires
• Technical Committee: F01 - Electronics
• Drafting Committee: F01.03 - Metallic Materials, Wire Bonding, and Flip Chip

Relations

• Replaces: ASTM F289-96(2009) - Standard Specification for Molybdenum Wire and Rod for Electronic Applications
• Effective Date: 01-Jun-2014
• Replaced By: ASTM F289-96(2019) - Standard Specification for Molybdenum Wire and Rod for Electronic Applications
• Effective Date: 01-Apr-2019
• Referred By: ASTM F219-96(2018) - Standard Test Methods of Testing Fine Round and Flat Wire for Electron Devices and Lamps (Withdrawn 2023)
• Effective Date: 01-Jun-2014
• Referred By: ASTM F290-94(2020) - Standard Specification for Round Wire for Winding Electron Tube Grid Laterals
• Effective Date: 01-Jun-2014
• Referred By: ASTM B387/B387M-23 - Standard Specification for Molybdenum and Molybdenum Alloy Bar, Rod, and Wire
• Effective Date: 01-Jun-2014

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F289 −96 (Reapproved 2014)
Standard Specification for
1
Molybdenum Wire and Rod for Electronic Applications
ThisstandardisissuedunderthefixeddesignationF289;thenumberimmediatelyfollowingthedesignationindicatestheyearoforiginal
adoptionor,inthecaseofrevision,theyearoflastrevision.Anumberinparenthesesindicatestheyearoflastreapproval.Asuperscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope E8Test Methods for Tension Testing of Metallic Materials
E315Test Methods for Chemical Analysis of Molybdenum
1.1 This specification covers two grades of molybdenum
3
(Withdrawn 2010)
wire less than 0.050 in. (1.27 mm) in diameter and one grade
F16Test Methods for Measuring Diameter or Thickness of
of molybdenum rod 1.00 in. (25.4 mm) or less in diameter as
Wire and Ribbon for Electronic Devices and Lamps
follows:
F205Test Method for Measuring Diameter of Fine Wire by
1.1.1 Grade 1—Commercially pure molybdenum wire suit-
Weighing
able for leads, hooks, supports, heaters, and metal-to-glass
F219Test Methods of Testing Fine Round and Flat Wire for
seals.
Electron Devices and Lamps
1.1.2 Grade 2—Commercially pure molybdenum wire suit-
2.2 Federal Standard:
able for mandrel either black or cleaned.
4
Fed. Std. No. 123Marking for Shipment (Civil Agencies)
1.1.3 Grade 3—Commercially pure molybdenum rod suit-
2.3 Military Standard:
able for leads, hooks, supports, and metal-to-glass seals.
MIL-STD-129Marking for Shipment and Storage (Military
1.2 The term wire applies to all spooled or coiled material
4
Agencies)
and 0.050 in. (1.3 mm) or less in diameter and to short cut
lengths 0.020 in. (0.51 mm) or less in diameter.
3. Chemical Composition
1.3 The term rod applies to all material over 0.020 in. (0.51
3.1 All grades of wire and rod shall be 99.90% minimum
mm) in diameter, supplied in straight lengths.
pure molybdenum. The maximum allowable oxygen content
1.4 The values stated in inch-pound units are to be regarded shall be 0.007 weight% , while the maximum carbon content
shall be 0.03 weight %.
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only
4. Mechanical Properties
and are not considered standard.
4.1 Tensile Properties:
1.5 This standard does not purport to address all of the
4.1.1 The tension test specimens and procedures shall con-
safety concerns, if any, associated with its use. It is the
form to Methods F219 for wire diameter up to and including
responsibility of the user of this standard to establish appro-
0.010 in. (0.25 mm), and Test Methods E8 for all other wire
priate safety and health practices and determine the applica-
and rod diameters.
bility of regulatory limitations prior to use.
4.1.2 The tensile requirements of wire in sizes up to and
2. Referenced Documents including 0.020 in. (0.51 mm) in diameter shall conform to the
2
requirements of Table 1 and shall be calculated by dividing the
2.1 ASTM Standards:
breaking load in grams-force by the size of the wire expressed
D374Test Methods for Thickness of Solid Electrical Insu-
3
in milligrams per 200 mm.
lation (Withdrawn 2013)
4.1.3 Thetensilerequirementsofwireinsizesover0.020in.
(0.51 mm) up to 0.050 in. (1.3 mm) in diameter shall conform
1 to the requirements of Table 2.
This specification is under the jurisdiction of ASTM Committee F01 on
Electronics and is the direct responsibility of Subcommittee F01.03 on Metallic
4.1.4 The tensile requirements of rod shall be as agreed
Materials.
upon between the purchaser and the supplier.
CurrenteditionapprovedJune1,2014.PublishedJuly2014.Originallyapproved
in 1954. Last previous edition approved in 2009 as F289 – 96 (2009). DOI: 4.2 Ductility Properties:
10.1520/F0289-96R14.
4.2.1 Wire up to 0.003 in. (0.08 mm) in diameter shall not
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
break when subjected to the test prescribed in 11.4.1.
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3 4
The last approved version of this historical standard is referenced on AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
www.astm.org. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F289−96 (2014)
TABLE 1 Tensile Requirements
Elongation in 10 in.
Wire Size, Minimum Tensile Breaking Load,
A
(250 mm), %
Maximum Diameter, in. (mm)
mg/200 mm gf/(mg/200 mm)
Grade 1 Grade 2
Up to 4.11, incl 0.0020 (0.051) 50 >6 #6
Over 4.11 to 6.42, incl 0.0025 (0.064) 46 >6 #6
Over 6.42 to 10.53, incl 0.0032 (0.081) 44 >6 #6
O
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F289 − 96 (Reapproved 2009) F289 − 96 (Reapproved 2014)
Standard Specification for
1
Molybdenum Wire and Rod for Electronic Applications
This standard is issued under the fixed designation F289; the number immediately following the designation indicates the year of original
adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript
epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers two grades of molybdenum wire less than 0.050 in. (1.27 mm) in diameter and one grade of
molybdenum rod 1.00 in. (25.4 mm) or less in diameter as follows:
1.1.1 Grade 1—Commercially pure molybdenum wire suitable for leads, hooks, supports, heaters, and metal-to-glass seals.
1.1.2 Grade 2—Commercially pure molybdenum wire suitable for mandrel either black or cleaned.
1.1.3 Grade 3—Commercially pure molybdenum rod suitable for leads, hooks, supports, and metal-to-glass seals.
1.2 The term wire applies to all spooled or coiled material and 0.050 in. (1.3 mm) or less in diameter and to short cut lengths
0.020 in. (0.51 mm) or less in diameter.
1.3 The term rod applies to all material over 0.020 in. (0.51 mm) in diameter, supplied in straight lengths.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
3
D374 Test Methods for Thickness of Solid Electrical Insulation (Withdrawn 2013)
E8 Test Methods for Tension Testing of Metallic Materials
3
E315 Test Methods for Chemical Analysis of Molybdenum (Withdrawn 2010)
F16 Test Methods for Measuring Diameter or Thickness of Wire and Ribbon for Electronic Devices and Lamps
F205 Test Method for Measuring Diameter of Fine Wire by Weighing
F219 Test Methods of Testing Fine Round and Flat Wire for Electron Devices and Lamps
2.2 Federal Standard:
4
Fed. Std. No. 123 Marking for Shipment (Civil Agencies)
2.3 Military Standard:
4
MIL-STD-129 Marking for Shipment and Storage (Military Agencies)
3. Chemical Composition
3.1 All grades of wire and rod shall be 99.90 % minimum pure molybdenum. The maximum allowable oxygen content shall
be 0.007 weight% , while the maximum carbon content shall be 0.03 weight %.
4. Mechanical Properties
4.1 Tensile Properties:
4.1.1 The tension test specimens and procedures shall conform to Methods F219 for wire diameter up to and including 0.010
in. (0.25 mm), and Test Methods E8 for all other wire and rod diameters.
1
This specification is under the jurisdiction of ASTM Committee F01 on Electronics and is the direct responsibility of Subcommittee F01.03 on Metallic Materials.
Current edition approved May 1, 2009June 1, 2014. Published July 2009 July 2014. Originally approved in 1954. Last previous edition approved in 20022009 as F289
– 96 (2002).(2009). DOI: 10.1520/F0289-96R09.10.1520/F0289-96R14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
4
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F289 − 96 (2014)
4.1.2 The tensile requirements of wire in sizes up to and including 0.020 in. (0.51 mm) in diameter shall conform to the
requirements of Table 1 and shall be calculated by dividing the breaking load in grams-force by the size of the wire expressed in
milligrams per 200 mm.
4.1.3 The tensile requirements of wire in sizes over 0.020 in. (0.51 mm) up to 0.050 in. (1.3 mm) in diameter shall conform
to the requirements of Table 2.
4.1.4 The tensile requirements of rod shall be as agreed upon between the purchaser and the supplier.
4.2 Ductility Properties
...