ASTM E1050-10
(Test Method)Standard Test Method for Impedance and Absorption of Acoustical Materials Using A Tube, Two Microphones and A Digital Frequency Analysis System
Standard Test Method for Impedance and Absorption of Acoustical Materials Using A Tube, Two Microphones and A Digital Frequency Analysis System
SIGNIFICANCE AND USE
This test method can be applied to measure sound absorption coefficients of absorptive materials at normal incidence, that is, 0°. It also can be used to determine specific impedance and admittance ratios. The properties measured with this test method are useful in basic research and product development of sound absorptive materials.
Normal incidence sound absorption coefficients can be quite useful in certain situations where the material is placed within a small acoustical cavity close to a sound source, for example a closely-fitted machine enclosure.
This test method allows one to compare relative values of sound absorption when it is impractical to procure large samples for accurate random-incidence measurements in a reverberation room. Estimates of the random incidence absorption coefficients can be obtained from normal impedance data for locally-reacting materials (2).
Note 2—The classification, “locally-reacting” includes fibrous materials having high internal losses. Formulas have been developed for converting sound absorption properties from normal incidence to random incidence, for both locally-reacting and bulk-reacing materials (3).
Measurements described in this test method can be made with high precision, but these measurements may be misleading. Uncertainties of greater magnitude than those from the measurements may occur from other sources. Care should be exercised to sample nonuniform materials adequately (see 11.1).
SCOPE
1.1 This test method covers the use of an impedance tube, two microphone locations, and a digital frequency analysis system for the determination of normal incidence sound absorption coefficients and normal specific acoustic impedance ratios of materials.
1.2 Laboratory Accreditation—A procedure for accrediting a laboratory for performing this test method is given in Annex A1.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the use of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: E1050 – 10
Standard Test Method for
Impedance and Absorption of Acoustical Materials Using a
Tube, Two Microphones and a Digital Frequency Analysis
1
System
This standard is issued under the fixed designation E1050; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
4
1. Scope Impedance Tube Method
ISO 10534–2 Acoustics—Determination of SoundAbsorp-
1.1 This test method covers the use of an impedance tube,
tionCoefficientandImpedanceinImpedanceTubes—Part
two microphone locations, and a digital frequency analysis
4
2: Transfer-Function Method
system for the determination of normal incidence sound
4
2.3 ANSI Standards:
absorption coefficients and normal specific acoustic impedance
ANSI/ASA S1.11 Octave-Band and Fractional-Octave-
ratios of materials.
Band Analog and Digital Filters
1.2 Laboratory Accreditation—A procedure for accrediting
a laboratory for performing this test method is given inAnnex
3. Terminology
A1.
3.1 Definitions—The acoustical terminology used in this
1.3 The values stated in SI units are to be regarded as
test method is intended to be consistent with the definitions in
standard. No other units of measurement are included in this
Terminology C634.
standard.
1.4 This standard does not purport to address the safety
NOTE 1—Historical literature regarding the measurement of normal
concerns, if any, associated with its use. It is the responsibility incidence absorption coefficients referred to “transfer function” measure-
ments; however, the term arises from Laplace transform theory and is not
of the use of this standard to consult and establish appropriate
strictly rigorous when the initial conditions have a non-zero value. The
safety and health practices and determine the applicability of
term “frequency response function” arises from more general Fourier
regulatory limitations prior to use.
5
transform theory (1). This test method shall retain the use of the former
term although not technically correct. Users should be aware that modern
2. Referenced Documents
FFT analyzers may employ the latter terminology.
2
2.1 ASTM Standards:
3.2 Symbols: The following symbols are used in Section 8
C384 Test Method for Impedance andAbsorption ofAcous-
(Procedure):
tical Materials by Impedance Tube Method
3.2.1 brc—normal specific acoustics susceptance ratio.
C634 Terminology Relating to Building and Environmental
3.2.2 c—speed of sound, m/s.
Acoustics
3.2.3 grc—normal specific acoustic conductance ratio.
E548 Guide for General Criteria Used for Evaluating Labo-
3.2.4 G ,G —auto power spectra of the acoustic pressure
3
11 22
ratory Competence
signal at microphone locations 1 and 2, respectively.
2.2 ISO Standards:
3.2.5 G —cross power spectrum of the acoustic pressure
12
ISO 10534-1 Acoustics—Determination of Sound Absorp-
signals at microphones locations 1 and 2.
tion Coefficient and Impedance or Admittance—Part 1:
3.2.6 H—transfer function of the two microphone signals
corrected for microphone response mismatch.
1 ¯
3.2.7 H—measured transfer function of the two micro-
ThistestmethodisunderthejurisdictionofASTMCommitteeE33onBuilding
and Environmental Acoustics and is the direct responsibility of Subcommittee
phone signals.
E33.01 on Sound Absorption. I II
3.2.8 H,H —calibration transfer functions for the micro-
Current edition approved Sept. 1, 2010. Published December 2010. Originally
phones in the standard and switched configurations, respec-
approved in 1985. Last previous edition approved in 2008 as E1050 - 08. DOI:
10.1520/E1050-10. tively.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
the ASTM website. 4th Floor, New York, NY 10036, http://www.ansi.org.
3 5
Withdrawn. The last approved version of this historical standard is referenced The boldface numbers in parentheses refer to the list of references at the end of
on www.astm.org. this test method.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
E1050 – 10
¯
3.2.9 H —complex microphone calibration factor. 5. Significance and Use
c
3.2.10 j—equals –1.
=
5.1 This test method can be applied to measure sound
-1
3.2.11 k—equal 2pf/c; wave number, m .
absorption coefficients of absorptive materials at normal inci-
3.2.11.1 Discussion—In general the wave numb
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:E1050–08 Designation: E1050 – 10
Standard Test Method for
Impedance and Absorption of Acoustical Materials Using Aa
Tube, Two Microphones and Aa Digital Frequency Analysis
1
System
This standard is issued under the fixed designation E1050; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This test method covers the use of an impedance tube, two microphone locations, and a digital frequency analysis system
forthedeterminationofnormalincidencesoundabsorptioncoefficientsandnormalspecificacousticimpedanceratiosofmaterials.
1.2 Laboratory Accreditation—Aprocedure for accrediting a laboratory for performing this test method is given inAnnexA1.
1.3
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the
use of this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C384 Test Method for Impedance and Absorption of Acoustical Materials by Impedance Tube Method
C634 Terminology Relating to Building and Environmental Acoustics
E548 Guide for General Criteria Used for Evaluating Laboratory Competence
2.2 ISO Standards:
ISO 10534-1 Acoustics—Determination of Sound Absorption Coefficient and Impedance or Admittance—Part 1: Impedance
3
Tube Method
ISO 10534–2 Acoustics—Determination of Sound Absorption Coefficient and Impedance in Impedance Tubes—Part 2:
3
Transfer-Function Method
3
2.3 ANSI Standards:
ANSI/ASA S1.11 Octave-Band and Fractional-Octave-Band Analog and Digital Filters
3. Terminology
3.1 Definitions—The acoustical terminology used in this test method is intended to be consistent with the definitions in
Terminology C634.
NOTE 1—Historical literature regarding the measurement of normal incidence absorption coefficients referred to “transfer function” measurements;
however,thetermarisesfromLaplacetransformtheoryandisnotstrictlyrigorouswhentheinitialconditionshaveanon-zerovalue.Theterm“frequency
4
responsefunction”arisesfrommoregeneralFouriertransformtheory(1). Thistestmethodshallretaintheuseoftheformertermalthoughnottechnically
correct. Users should be aware that modern FFT analyzers may employ the latter terminology.
3.2 Symbols: The following symbols are used in Section 8 (Procedure):
3.2.1 brc—normal specific acoustics susceptance ratio.
3.2.2 c—speed of sound, m/s.
3.2.3 grc—normal specific acoustic conductance ratio.
1
This test method is under the jurisdiction of ASTM Committee E33 on Building and Environmental Acoustics and is the direct responsibility of Subcommittee E33.01
on Sound Absorption.
Current edition approved Jan. 15, 2008. Published February 2008. Originally approved in 1985. Last previous edition approved in 2007 as E1050-07. DOI:
10.1520/E1050-08.
Current edition approved Sept. 1, 2010. Published December 2010. Originally approved in 1985. Last previous edition approved in 2008 as E1050 - 08. DOI:
10.1520/E1050-10.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
4
The boldface numbers in parentheses refer to the list of references at the end of this test method.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
E1050 – 10
3.2.4 G ,G —auto power spectra of the acoustic pressure signal at microphone locations 1 and 2, respectively.
11 22
3.2.5 G —cross power spectrum of the acoustic pressure signals at microphones locations 1 and 2.
12
3.2.6 H—transfer function of the two microphone signals corrected for microphone response mismatch.
¯
3.2.7 H—measured transfer function of the two microphone signals.
I II
3.2.8 H,H —calibration transfer functions for the microphones in the standard and switched configurations, r
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.