ASTM C140-08
(Test Method)Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units
SIGNIFICANCE AND USE
These test methods provide general testing requirements for application to a broad range of concrete products. Those general testing requirements are included in the body of this standard.
Note 2—Consult manufacturer, supplier, product specifications, or other resources for more specific measurement or testing guidelines for those products not addressed with the annex of this standard.
These test methods provide specific testing requirements in two distinct sections, the requirements applicable to all units covered by these test methods and those applicable to the specific unit types. The requirements applicable to all units are included in the body of these test methods and those applicable to the specific unit types are included within the annexes.
SCOPE
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength, absorption, unit weight (density), moisture content, flexural load, and ballast weight. Not all methods are applicable to all unit types, however.
1.2 Specific testing and reporting procedures are included in annexes to these test methods for the following specific unit types: Annex A1—Concrete masonry units (Specifications C 90, C 129) Annex A2—Concrete brick (Specifications C 55, C 73, C 1634) Annex A3—Segmental retaining wall units (Specification C 1372) Annex A4—Concrete interlocking paving units (Specification C 936) Annex A5—Concrete grid paving units (Specification C 1319) Annex A6—Concrete roof pavers (Specification C 1491)
1.3 The test procedures included in these test methods are also applicable to other types of units not referenced in these test methods, but specific testing and reporting requirements for those units are not included.
1.4 These test methods include the following sections: Section Scope1 Referenced Documents2 Terminology3 Significance and Use4 Sampling5 Measurement of Dimensions6 Compressive Strength7 Absorption8 Calculations9 Report10 Keywords11 Annexes—Test Procedures Concrete Masonry UnitsAnnex A1 Concrete BrickAnnex A2 Segmental Retaining Wall UnitsAnnex A3 Concrete Interlocking Paving UnitsAnnex A4 Concrete Grid Paving UnitsAnnex A5 Concrete Roof PaversAnnex A6 Determining Plate Thickness Requirements for Compression TestingAnnex A7 Worksheet and Test Report for Concrete Masonry UnitsAppendix X1
Note 1—The testing laboratory performing these test methods should be evaluated in accordance with Practice C 1093.
1.5 The values stated in inch-pound units are to be regarded as the standard, except in Annex A4, where SI units are to be regarded as standard. The values given in parentheses throughout are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C140–08
Standard Test Methods for
Sampling and Testing Concrete Masonry Units and Related
1
Units
This standard is issued under the fixed designation C 140; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
NOTE 1—The testing laboratory performing these test methods should
1. Scope*
be evaluated in accordance with Practice C 1093.
1.1 These test methods provide various testing procedures
1.5 The values stated in inch-pound units are to be regarded
commonly used for evaluating characteristics of concrete
as the standard, except in Annex A4, where SI units are to be
masonryunitsandrelatedconcreteunits.Methodsareprovided
regarded as standard. The values given in parentheses through-
for sampling, measurement of dimensions, compressive
out are mathematical conversions to SI units that are provided
strength, absorption, unit weight (density), moisture content,
for information only and are not considered standard.
flexural load, and ballast weight. Not all methods are appli-
1.6 This standard does not purport to address all of the
cable to all unit types, however.
safety concerns, if any, associated with its use. It is the
1.2 Specific testing and reporting procedures are included in
responsibility of the user of this standard to establish appro-
annexes to these test methods for the following specific unit
priate safety and health practices and determine the applica-
types:
bility of regulatory limitations prior to use.
Annex A1—Concrete masonry units (Specifications C 90, C 129)
Annex A2—Concrete brick (Specifications C 55, C 73, C 1634)
Annex A3—Segmental retaining wall units (Specification C 1372) 2. Referenced Documents
Annex A4—Concrete interlocking paving units (Specification C 936)
2
2.1 ASTM Standards:
Annex A5—Concrete grid paving units (Specification C 1319)
Annex A6—Concrete roof pavers (Specification C 1491) C55 Specification for Concrete Building Brick
C73 Specification for Calcium Silicate Brick (Sand-Lime
1.3 The test procedures included in these test methods are
Brick)
also applicable to other types of units not referenced in these
C90 Specification for Loadbearing Concrete Masonry
test methods, but specific testing and reporting requirements
Units
for those units are not included.
C 129 Specification for Nonloadbearing Concrete Masonry
1.4 These test methods include the following sections:
Units
Section
C 143/C 143M Test Method for Slump of Hydraulic-
Scope 1
Referenced Documents 2 Cement Concrete
Terminology 3
C 936 Specification for Solid Concrete Interlocking Paving
Significance and Use 4
Units
Sampling 5
Measurement of Dimensions 6
C 1093 Practice for Accreditation of Testing Agencies for
Compressive Strength 7
Masonry
Absorption 8
C 1209 Terminology of Concrete Masonry Units and Re-
Calculations 9
Report 10 lated Units
Keywords 11
C 1232 Terminology of Masonry
Annexes—Test Procedures
C 1319 Specification for Concrete Grid Paving Units
Concrete Masonry Units Annex A1
Concrete Brick Annex A2
C 1372 Specification for Dry-Cast Segmental Retaining
Segmental Retaining Wall Units Annex A3
Wall Units
Concrete Interlocking Paving Units Annex A4
C 1491 Specification for Concrete Roof Pavers
Concrete Grid Paving Units Annex A5
Concrete Roof Pavers Annex A6
C 1552 Practice for Capping Concrete Masonry Units, Re-
Determining Plate Thickness Requirements for Compression Testing Annex A7
lated Units and Masonry Prisms for Compression Testing
Worksheet and Test Report for Concrete Masonry Units Appendix X1
C 1634 Specification for Concrete Facing Brick
1
These test methods are under the jurisdiction of ASTM Committee C15 on
2
Manufactured Masonry Units and are the direct responsibility of Subcommittee For referenced ASTM standards, visit the ASTM website, www.astm.org, or
C15.03 on Concrete Masonry Units and Related Units. contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Current edition approved Aug. 1, 2008. Published September 2008. Originally Standards volume information, refer to the standard’s Document Summary page on
approved in 1938. Last previous edition approved in 2007 as C 140 – 07a. the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C140–08
determined after units reached equilibrium with lab environment, or
E4 Practices for Force Verification of Testing Machines
before units were shipped, or after delivery to the job site, and so forth.
E6 Terminology Relating to
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:C140–07a Designation:C140–08
Standard Test Methods for
Sampling and Testing Concrete Masonry Units and Related
1
Units
This standard is issued under the fixed designation C 140; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 These test methods provide various testing procedures commonly used for evaluating characteristics of concrete masonry
units and related concrete units. Methods are provided for sampling, measurement of dimensions, compressive strength,
absorption, unit weight (density), moisture content, flexural load, and ballast weight. Not all methods are applicable to all unit
types, however.
1.2 Specific testing and reporting procedures are included in annexes to these test methods for the following specific unit types:
Annex A1—Concrete masonry units (Specifications C 90, C 129)
Annex A2—Concrete brick (Specifications C 55, C 1634)
Annex A2—Concrete brick (Specifications C 55, C 73, C 1634)
Annex A3—Segmental retaining wall units (Specification C 1372)
Annex A4—Concrete interlocking paving units (Specification C 936)
Annex A5—Concrete grid paving units (Specification C 1319)
Annex A6—Concrete roof pavers (Specification C 1491)
1.3 The test procedures included in these test methods are also applicable to other types of units not referenced in these test
methods, but specific testing and reporting requirements for those units are not included.
1.4 These test methods include the following sections:
Section
Scope 1
Referenced Documents 2
Terminology 3
Significance and Use 4
Sampling 5
Measurement of Dimensions 6
Compressive Strength 7
Absorption 8
Calculations 9
Report 10
Keywords 11
Annexes—Test Procedures
Concrete Masonry Units Annex A1
Concrete Brick Annex A2
Segmental Retaining Wall Units Annex A3
Concrete Interlocking Paving Units Annex A4
Concrete Grid Paving Units Annex A5
Concrete Roof Pavers Annex A6
Determining Plate Thickness Requirements for Compression Testing Annex A7
Worksheet and Test Report for Concrete Masonry Units Appendix X1
NOTE 1—The testing laboratory performing these test methods should be evaluated in accordance with Practice C 1093.
1.5The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.5 The values stated in inch-pound units are to be regarded as the standard, except in Annex A4, where SI units are to be
regarded as standard. The values given in parentheses throughout are mathematical conversions to SI units that are provided for
information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
1
These test methods are under the jurisdiction of ASTM Committee C15 on Manufactured Masonry Units and are the direct responsibility of Subcommittee C15.03 on
Concrete Masonry Units and Related Units.
Current edition approved Dec. 15, 2007.Aug. 1, 2008. Published JanuarySeptember 2008. Originally approved in 1938. Last previous edition approved in 2007 as
C 140 – 07a.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C140–08
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
C 55 Specification for Concrete Building Brick
C 73 Specification for Calcium Silicate Brick (Sand-Lime Brick)
C 90 Specification for Loadbearing Concrete Masonry Units
C 129 Specification for Nonloadbearing Concrete Masonry Units
C 143/C 143M Test Method for Slump of Hydraulic-Cement Concrete
C 936 Specification for Solid Concrete Interlocking Paving Units
C 1093 Practice for Accreditation of Testing Agencies for Masonry
C 1209 Terminology of Concrete Masonry Units and Related Units
C 1232 Terminology of Masonry
C 1319 Specification for Concrete Grid Paving Units
C 1372 Specification for Dry-Cast Segmental Retaining Wall Units
C 1491 Specification for Concrete Roof Pavers
C 1552 Practice for Capping Concrete M
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.