ASTM D3917-23
(Specification)Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes
Standard Specification for Dimensional Tolerance of Thermosetting Glass-Reinforced Plastic Pultruded Shapes
ABSTRACT
This specification defines the dimensional tolerances of standard rods, bars, and shapes pultruded from thermosetting glass-reinforced plastics. Tolerances cover dimensional criteria for cross sections, width or diameter, straightness, twist, surface flatness, angularity, and camber.
SCOPE
1.1 This specification defines production tolerances applicable to standard rods, bars, shapes, and flat sheet pultruded from thermosetting glass-reinforced plastics.
1.2 These dimensional tolerances apply to all shapes specified as “standard” by the pultrusion industry.
1.3 Custom shapes and products designed for special applications may carry specific tolerances that vary from the standard.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1: There is no known ISO equivalent to this standard.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3917 − 23
Standard Specification for
Dimensional Tolerance of Thermosetting Glass-Reinforced
1
Plastic Pultruded Shapes
This standard is issued under the fixed designation D3917; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 1.6 This international standard was developed in accor-
dance with internationally recognized principles on standard-
1.1 This specification defines production tolerances appli-
ization established in the Decision on Principles for the
cable to standard rods, bars, shapes, and flat sheet pultruded
Development of International Standards, Guides and Recom-
from thermosetting glass-reinforced plastics.
mendations issued by the World Trade Organization Technical
1.2 These dimensional tolerances apply to all shapes speci-
Barriers to Trade (TBT) Committee.
fied as “standard” by the pultrusion industry.
2. Referenced Documents
1.3 Custom shapes and products designed for special appli-
2
2.1 ASTM Standards:
cations may carry specific tolerances that vary from the
D883 Terminology Relating to Plastics
standard.
3. Terminology
1.4 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical
3.1 Definitions:
conversions to SI units that are provided for information only
3.1.1 camber—the deviation of the edge or surface from a
and are not considered standard.
reference straight line with the weight of the pultrusion not
1.5 The following safety hazards caveat pertains only to the minimizing the measurement.
test methods portion, Section 5, of this specification: This
3.1.2 flat sheet—a rectangular solid pultruded profile with a
standard does not purport to address all of the safety concerns,
width of 12 in. up to and including 78 inches.
if any, associated with its use. It is the responsibility of the user
3.1.3 mean wall thickness—the average of two or more wall
of this standard to establish appropriate safety, health, and
thickness measurements taken at multiple locations.
environmental practices and determine the applicability of
3.1.4 straightness—the upward deviation of a pultruded
regulatory limitations prior to use.
shape when resting on a flat surface measured in a manner that
NOTE 1—There is no known ISO equivalent to this standard.
the weight of the pultruded part minimizes the deviation.
3.2 For definitions or terms that are not defined in this
standard, refer to Terminology D883.
1
This specification is under the jurisdiction of ASTM Committee D20 on
Plastics and is the direct responsibility of Subcommittee D20.18 on Reinforced
2
Thermosetting Plastics. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Nov. 1, 2023. Published November 2023. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1980. Last previous edition approved in 2015 as D3917 - 15a. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/D3917-23. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3917 − 23
4. Dimensional Criteria 4.1.3 For wall thickness and flatsheets of thickness over
0.125 in. (3.175 mm) dimensions, if the calculated tolerance as
4.1 Cross-sectional dimensions for standard rods, bars, and
per above table is more than 0.05 in. (1.27 mm), the thickness
shapes shall be prescribed in Table 1.
tolerance shall be 60.05 in. (1.27 mm).
4.1.1 For die struck dimension, if the calculated tolerance as
per above table is more than 0.094 in. (2.39 mm), then the die
4.2 Length tolerances for standard rods, bars, and shapes
struck dimension tolerance shall be 60.094 in. (2.39 mm).
shall be as prescribed in Table 2.
4.1.2 For wall thickness of open shapes and closed shapes
4.3 Straightness tolerances shall be as prescribed in Table 3
and flatsheets of thickness under 0.125 in. (3.175 mm)
dimensions, if the calculated tolerance as per above table is less (also see 5.2).
than 0.01 in. (0.25 mm), the thickness tolerance shall be 60.01
in. (0.25 mm).
TABLE 1 Cross-Sectional Dimensions—Standard Rods, Bars, and Shapes
Solid Dimensions, ±in. (mm)
A B B C
B B
Die Struck Wall Thickness Thickness (Flat Sheets) Wall Thickness
A, B
(Open Shape) (Closed Shape)
Dim
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3917 − 15a D3917 − 23
Standard Specification for
Dimensional Tolerance of Thermosetting Glass-Reinforced
1
Plastic Pultruded Shapes
This standard is issued under the fixed designation D3917; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification defines production tolerances applicable to standard rods, bars, shapes, and flat sheet pultruded from
thermosetting glass-reinforced plastics.
1.2 These dimensional tolerances apply to all shapes specified as “standard” by the pultrusion industry.
1.3 Custom shapes and products designed for special applications may carry specific tolerances that vary from the standard.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 The following safety hazards caveat pertains only to the test methods portion, Section 45, of this specification: This standard
does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety and healthsafety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
NOTE 1—There is no known ISO equivalent to this standard.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D883 Terminology Relating to Plastics
3. Terminology
3.1 Definitions:
3.1.1 camber—the deviation of the edge or surface from a reference straight line with the weight of the pultrusion not minimizing
the measurement.
1
This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibility of Subcommittee D20.18 on Reinforced Thermosetting
Plastics.
Current edition approved Oct. 1, 2015Nov. 1, 2023. Published October 2015November 2023. Originally approved in 1980. Last previous edition approved in 2015 as
D3917 - 15.D3917 - 15a. DOI: 10.1520/D3917-15A.10.1520/D3917-23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3917 − 23
3.1.2 flat sheet—a rectangular solid pultruded profile with a width of 12 in. up to and including 78 inches.
3.1.3 mean wall thickness—the average of two or more wall thickness measurements taken at multiple locations.
3.1.4 straightness—the upward deviation of a pultruded shape when resting on a flat surface measured in a manner that the weight
of the pultruded part minimizes the deviation.
3.2 For definitions or terms that are not defined in this standard, refer to Terminology D883.
2
---------------------- Page: 2 ----------------------
D3917 − 23
4. Dimensional Criteria
4.1 Cross-sectional dimensions for standard rods, bars, and shapes shall be prescribed in Table 1.
4.1.1 For die struck dimension, if the calculated tolerance as per above table is more than 0.094 in. (2.39 mm), then the die struck
dimension tolerance shall be 60.094 in. (2.39 mm).
4.1.2 For wall thickness of open shapes and closed shapes and flatsheets of thickness under 0.125 in. (3.175 mm) dimensions, if
the calculated tolerance as per above table is less than 0.01 in. (0.25 mm), the thickness tolerance shall be 60.01 in. (0.25 mm).
4.1.3 For wall thickness and flatsheets of thickness over 0.125 in. (3.175 mm) dimensions, if the calculated tolerance as per above
table is more than 0.05 in. (1.27 mm), the thickness tolerance shall be 60.05 in. (1.27 mm).
4.2 Length tolerances for standard rods, bars, and shapes shall be as prescribed in Table 2.
4.3 Straightness toler
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.