iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1996-00

(Test Method)

Standard Test Method for Silver Migration for Membrane Switch Circuitry

Standard Test Method for Silver Migration for Membrane Switch Circuitry

SCOPE
1.1 This test method is used to determine the susceptibility of a membrane switch to the migration of the silver between circuit traces under dc voltage potential.
1.2 Silver migration will occur when special conditions of moisture and electrical energy are present.

General Information

Status
Historical
Publication Date
09-Jun-2001
ICS
77.120.99 - Other non-ferrous metals and their alloys
Technical Committee
F01 - Electronics
Drafting Committee
F01.18 - Printed Electronics
Current Stage
Ref Project

Relations

Replaced By
ASTM F1996-01 - Standard Test Method for Silver Migration for Membrane Switch Circuitry
Effective Date
10-Jun-2001
Referred By
ASTM F3147-15 - Standard Test Method for Evaluating the Reliability of Surface Mounted Device (SMD) Joints on a Flexible Circuit by a Rolling Mandrel Bend (Withdrawn 2024)
Effective Date
10-Jun-2001

Buy Standard

ASTM F1996-00 - Standard Test Method for Silver Migration for Membrane Switch CircuitryASTM F1996-00 - Standard Test Method for Silver Migration for Membrane Switch Circuitry
PreviousNext
Standard
ASTM F1996-00 - Standard Test Method for Silver Migration for Membrane Switch Circuitry
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


NOTICE: This standard has either been superseded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: F 1996 – 00
Standard Test Method for
Silver Migration for Membrane Switch Circuitry
This standard is issued under the fixed designation F 1996; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope 5.1.7 Dendrites normally grow from the cathode conductor
to the anode. To test both electrodes of a switch design connect
1.1 This test method is used to determine the susceptibility
replicate specimen so that current flows through them in
of a membrane switch to the migration of the silver between
opposite directions.
circuit traces under dc voltage potential.
5.1.8 Without limited current, the migration could occur,
1.2 Silver migration will occur when special conditions of
causing a short and a dramatic current surge, which then
moisture and electrical energy are present.
destroys the short and returns the circuit to a nonstandard, but
2. Referenced Documents
functional condition. If an observer was not present (or the
details were not continuously recorded) this most dramatic
2.1 ASTM Standards:
failure might go unnoticed.
F 1596 Practice for Exposure of Membrane Switches to
Temperature and Relative Humidity
6. Apparatus
F 1689 Test Method for Determining the Insulation Resis-
6.1 Closed Environmental System, with temperature and
tance of a Membrane Switch
humidity control (see Practice F 1596).
3. Terminology
6.2 Current-Limiting DC Power Source. (Series current
limiting resistor may be used with dc power supply).
3.1 Definitions:
6.3 Milliamp Meter (see Test Method F 1689).
3.1.1 silver migration—A process by which silver, when in
6.4 Megohm Meter.
contact with insulating materials under electrical potential, is
6.5 Test Surface, flat, smooth, unyielding, nonporous, and
removed ionically from its original location, and is redeposit as
larger than switch under test.
a metal (silver dendrite) at some other location.
7. Procedure
4. Significance and Use
7.1 Pretest Setup:
4.1 The effects of silver migration are short circuiting or
7.1.1 Test specimen(s) shall be permitted to stabilize at 20 to
reduction in insulation resistance. It is evidenced by staining or
25°C and 40 to 60 % relative humidity (RH) for a minimum of
dicoloration between the cathode and anode conductive traces.
24 h.
4.2 Accelerated testing may be accomplished by increasing
7.2 Test Setup (Fig. 1):
the voltage over the specified voltages. (A typical starting point
7.2.1 Secure switch on test surface and measure initial
would be 5Vdc 50mA).
insulation resistance between test points and record results.
5. Interferences
7.2.2 Place switch at a 90 6 15° to horizontal (unless
otherwise specified) in the test chamber to prevent condensate
5.1 The following parameters may affect the results of this
accumulation.
test:
7.2.3 Connect power supply leads to test points.
5.1.1 Temperature.
7.3 In Process Test:
5.1.2 Relative Humidity.
7.3.1 Apply voltage to th
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B541-24(Specification)
Standard Specification for Gold Electrical Contact Alloy

ABSTRACT
This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts. The material shall be finished by cold working, annealing, turning, grinding, and age hardening. The materials shall conform to the specified chemical composition requirements. Tensile strength, elongation, and hardness shall be determined by tension and hardness tests. Chemical analysis shall be done by spectrochemical or wet analysis methods.
SCOPE
1.1 This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains to the test method portion only, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM B277-18(2024)(Test Method)
Standard Test Method for Hardness of Electrical Contact Materials

SIGNIFICANCE AND USE
3.1 The Rockwell hardness and Rockwell superficial tests are useful when the test specimens are sufficiently thick (in relation to the indentor load) to ensure that the results are not affected by the flow of metal on the surface of the anvil. On a solid piece the flow of metal on the under surface may be detected by a bulge or marking. On composite pieces where the contact materials are attached to backings of a different material, the thickness limitations imposed for a solid piece shall apply to the contact material portion of such composite pieces.
Note 1: As a matter of information, it may be stated that tests on fine silver showed that on annealed samples having a Rockwell 15T hardness of 27, the readings were not affected on thicknesses 1/16 in. (1.6 mm) or over. On thicknesses of 1/32 in. (0.8 mm) Rockwell 15T scale readings of 72 and higher were not affected.  
3.2 The microindentation hardness test is of questionable significance when the metallic phases in a material are so large that the indentation does not represent an accurate average hardness. Sintered contact materials usually contain segregates differing greatly in hardness from the matrix hardness and may destroy the validity of microindentation hardness readings.  
3.3 Other aspects of significance and use shall be as described in the particular ASTM test method used, as listed in Section 2.
SCOPE
1.1 This test method covers the determination of the hardness of metallic materials used for electrical contacts. Rockwell, Rockwell superficial, Brinell, and microindentation hardness tests are included, along with information on the limitations and use of these tests.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar will all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM E439-23(Test Method)
Standard Test Methods for Chemical Analysis of Beryllium

SIGNIFICANCE AND USE
4.1 These test methods for the chemical analysis of beryllium metal are primarily intended as referee methods to test such materials for compliance with compositional specifications. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory.
SCOPE
1.1 These test methods cover the chemical analysis of beryllium having chemical compositions within the following limits:    
Element  
Range, %  
Aluminum  
0.05 to 0.30  
Beryllium  
97.5 to 100    
Beryllium Oxide  
0.3 to 3    
Carbon  
0.05 to 0.30  
Copper  
0.005 to 0.10  
Chromium  
0.005 to 0.10  
Iron  
0.05 to 0.30  
Magnesium  
0.02 to 0.15  
Nickel  
0.005 to 0.10  
Silicon  
0.02 to 0.15  
1.2 The test methods in this standard are contained in the sections as follows.    
Sections  
Chromium by the Diphenylcarbazide Spectrophotometric Test Method
[0.004 % to 0.04 %]  
10 – 19  
Iron by the 1,10-Phenanthroline Spectrophotometric Test Method
[0.05 % to 0.25 %]  
20 – 29  
Manganese by the Periodate Spectrophotometric Test Method
[0.008 % to 0.04 %]  
30 – 39  
Nickel by the Dimethylglyoxime Spectrophotometric Test Method
[0.001 % to 0.04 %]  
40 – 49  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E3097-23(Test Method)
Standard Test Method for Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys

SIGNIFICANCE AND USE
5.1 Constant force thermal cycling tests determine the effect of stress on the transformation temperatures, recovered strain and residual strain of a shape memory alloy. The tests may be for one thermal cycle. A standard test method for force controlled repeated thermal cycling of shape memory alloys is currently under development.  
5.2 Measurement of the specimen's thermomechanical behavior closely parallels many shape memory applications and provides a result that is applicable to the function of the material.  
5.3 This test method may be used for, but is not limited to, wire, round tube, or strip samples. Thus it is able to provide an assessment of the product in its semi-finished form.  
5.4 This test method provides a simple method for determining transformation temperatures by heating and cooling specimens through their full thermal transformation under force.  
5.5 This test method can be used on trained and processed material in a semi-finished form to measure Two Way Shape Memory Effect by comparing the strain in the austenite state and martensite states with no minimal applied stress. The force is set to a minimum value not to exceed a corresponding stress of 7 MPa (in accordance Test Method F2516).  
5.6 This test method is useful for quality control, specification acceptance, and research.  
5.7 Transformation temperatures derived from this test method may not agree with those obtained by other test methods due to the effects of strain and stress on the transformation.  
5.8 Components such as springs or other semi-finished parts can be tested using this method as agreed upon by the customer and supplier. Units of stress and strain can be replaced with force and displacement.
SCOPE
1.1 This test method defines procedures for thermomechanical cycling of shape memory alloy (SMA) material and components under constant force. This method characterizes the transformation properties such as transformation temperatures, actuation strain and residual strain, when a SMA is thermally cycled through the phase transformation under a constant applied force. This test is done to provide data for the selection of SMA materials, quality control, design allowables and actuator design.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM B561-23(Specification)
Standard Specification for Refined  Platinum

ABSTRACT
This specification covers refined platinum as sponge, cast bar, and wrought forms in two grades as follows: Grade 99.95 and Grade 99.99. The refined platinum shall conform to the required chemical composition for platinum, rhodium, palladium, ruthenium, iridium, gold, silver, lead, tin, zinc, iron, manganese, copper, silicon, calcium, magnesium, aluminum, nickel, chromium, antimony, arsenic, bismuth, tellurium, cadmium, and molybdenum. The metal may be produced by refining process that yields a product capable of meeting the chemical requirements of this specification.
SCOPE
1.1 This specification covers refined platinum as sponge, cast bar, and wrought forms (Note 1) in two grades as follows:  
1.1.1 Grade 99.95 (UNS PO4995)—Platinum having a purity of 99.95 %, min, and  
1.1.2 Grade 99.99—Platinum having a purity of 99.99 % min.  
Note 1: Other forms of unfabricated platinum of commerce are not to be excluded under this specification.
Note 2: For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right hand place of figures used in expressing the limiting value, in accordance with the rounding off method of Practice E29.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B616-23(Specification)
Standard Specification for Refined Rhodium

ABSTRACT
This specification covers refined rhodium as sponge and powder in three grades, namely: Grade 99.80, Grade 99.90, and Grade 99.95. The material may be produced by any refining process that will yield a product capable of meeting the chemical composition requirements specified for rhodium, platinum, iridium, palladium, ruthenium, lead, tin, zinc, arsenic, bismuth, cadmium, iron, silicon, silver, gold, copper, nickel, tellurium, magnesium, calcium, aluminum, chromium, manganese, antimony, cobalt, and boron determined by chemical analysis. Sampling requirements for the metal sponge and powder are detailed.
SCOPE
1.1 This specification covers refined rhodium as sponge and powder in three grades as follows:  
1.1.1 Grade 99.80—Rhodium having a purity of 99.80 %,  
1.1.2 Grade 99.90—Rhodium having a purity of 99.90 %, and  
1.1.3 Grade 99.95—Rhodium having a purity of 99.95 %.  
1.1.4 For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the limiting value, in accordance with the rounding method of Practice E29.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B692-18(2023)(Specification)
Standard Specification for 75 % Silver-25 % Graphite Sliding Contact Material

ABSTRACT
This specification defines the criteria for the chemical composition and other requirements (including physical properties, microstructure, superficial hardness, and specific resistance ) for silver-graphite brushes for sliding electrical contacts. The percentage of silver, graphite, ash in graphite, and total metal impurities are prescribed. The minimum acceptable values for the physical properties such as density, determined by measurement and weight method, and shear strength are given. Typical Rockwell hardness and specific resistance for the material are also specified.
SCOPE
1.1 This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 75 weight % with the balance being substantially graphite.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B664-18(2023)(Specification)
Standard Specification for 80 % Silver-20 % Graphite Sliding Contact Material

ABSTRACT
This specification defines the criteria for composition and other requirements for sliding contact materials or brushes with a nominal composition by weight of 20% silver and 80% graphite. Materials shall adhere to specified requirements for chemical composition, density, shear strength, and microstructure. They shall also conform to typical values of Rockwell superficial hardness and specific resistance.
SCOPE
1.1 This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 80 %, by weight, with the balance being substantially graphite.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar will all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B717-23(Specification)
Standard Specification for Refined Ruthenium

ABSTRACT
This specification covers refined ruthenium as sponge and powder in one grade as follows: Grade 99.80 and Grade 99.90. The material may be produced by any refining process that yields a product capable of meeting the chemical requirements of this specification. The material should conform to the requirements for chemical composition as prescribed.
SCOPE
1.1 This specification covers refined ruthenium as sponge and powder in one grade as follows:  
1.1.1 Grade 99.80—Ruthenium having a purity of 99.80 %.  
1.1.2 Grade 99.90—Ruthenium having a purity of 99.90 %.  
Note 1: For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the limiting value in accordance with the rounding method of Practice E29.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM E1615-22(Test Method)
Standard Test Method for Determination of Trace Quantities of Iron by Visible Spectrophotometry

SIGNIFICANCE AND USE
4.1 This test method is suitable for determining trace concentrations of iron in a wide variety of products, provided that appropriate sample preparation has rendered the iron and sample matrix soluble in water or other suitable solvent. Each sample matrix must be investigated for suitability using this test method.  
4.2 This test method assumes that the amount of color developed is proportional to the amount of iron in the test solution. The calibration curve is linear over the specified range.
SCOPE
1.1 This test method covers the determination of iron in aromatic hydrocarbons, their derivatives, and related chemicals in the range from 0.01 to 0.2 μg/g using [3-(2-pyridyl)-5,6-bis(4-phenylsulfonic acid)-1,2,4-triazine, monosodium salt, monohydrate] (PDTS)2 reagent solution. The range may be extended through the use of a 5- or 10-cm cell or by suitable dilution of the sample solution.  
1.2 The limit of detection (LOD) is 0.01 µg/kg for iron and the limit of quantitation (LOQ) is 0.04 µg/kg.
Note 1: The LOD and LOQ were calculated using data from the ILS.  
1.3 This test method is intended to be general for the final steps in the determination of iron and does not include procedures for sample preparation.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 Review the current Safety Data Sheets (SDS) for detailed information concerning toxicity, first-aid procedures, and safety precautions.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see Section 8.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off