ASTM D7055-14
(Practice)Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings
Standard Practice for Preparation (by Abrasive Blast Cleaning) of Hot-Rolled Carbon Steel Panels for Testing of Coatings
SIGNIFICANCE AND USE
4.1 The procedures described in this practice are designed to provide hot-rolled, carbon steel panels with uniform and reproducible abrasive blast cleaned surfaces for testing of coatings.
SCOPE
1.1 This practice covers the procedures to be followed in the preparation (by abrasive blast cleaning) of hot rolled steel panels for laboratory testing of coatings.
1.2 This standard practice does not include procedures for the application of coatings.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7055 − 14
Standard Practice for
Preparation (by Abrasive Blast Cleaning) of Hot-Rolled
1
Carbon Steel Panels for Testing of Coatings
This standard is issued under the fixed designation D7055; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.2 ISO Standard:
ISO 8502-3, Part 3 Assessment of Dust on Steel Surfaces
1.1 Thispracticecoverstheprocedurestobefollowedinthe
3
Prepared for Painting (pressure-sensitive tape method)
preparation (by abrasive blast cleaning) of hot rolled steel
4
panels for laboratory testing of coatings.
2.3 SSPC/NACE Standards:
AB-1 Mineral and Slag Abrasives
1.2 This standard practice does not include procedures for
AB-2 Specification for Cleanliness of Recycled Ferrous
the application of coatings.
Metallic Abrasives
1.3 The values stated in inch-pound units are to be regarded
AB-3 Newly Manufactured or Re-Manufactured SteelAbra-
as standard. The values given in parentheses are mathematical
sives
conversions to SI units that are provided for information only
SP 1 Solvent Cleaning
and are not considered standard.
SP 5/NACE No. 1 White Metal Blast Cleaning
1.4 This standard does not purport to address all of the
SP 6/NACE No. 3 Commercial Blast Cleaning
safety concerns, if any, associated with its use. It is the
SP 10/NACE No. 2 Near-White Metal Blast Cleaning
responsibility of the user of this standard to establish appro-
SSPC-VIS 1 Guide and Reference Photographs for Steel
priate safety and health practices and determine the applica-
Surfaces Prepared by Dry Abrasive Blast Cleaning
bility of regulatory limitations prior to use.
3. Summary of Practice
2. Referenced Documents
2
3.1 This practice enables the user to specify the level of
2.1 ASTM Standards:
preparation of hot-rolled carbon steel test panels (prepared by
A36/A36M Specification for Carbon Structural Steel
dry abrasive blast cleaning) for testing of coatings, including
A572/A572M Specification for High-Strength Low-Alloy
Columbium-Vanadium Structural Steel thesteelcomposition,thedegreeofsurfacecleanliness,andthe
A1011/A1011M Specification for Steel, Sheet and Strip, type of abrasive.
Hot-Rolled, Carbon, Structural, High-Strength Low-
Alloy, High-Strength Low-Alloy with Improved 4. Significance and Use
Formability, and Ultra-High Strength
4.1 Theproceduresdescribedinthispracticearedesignedto
D4285 Test Method for Indicating Oil or Water in Com-
provide hot-rolled, carbon steel panels with uniform and
pressed Air
reproducible abrasive blast cleaned surfaces for testing of
D4417 Test Methods for Field Measurement of Surface
coatings.
Profile of Blast Cleaned Steel
D4940 Test Method for Conductimetric Analysis of Water
5. Test Panels
Soluble Ionic Contamination of Blasting Abrasives
D7393 Practice for Indicating Oil in Abrasives
5.1 Prepare the test panels from unpainted hot-rolled steel
plate or bar stock.
1
This practice is under the jurisdiction of ASTM Committee D01 on Paint and
5.2 The panels shall be made to a size and thickness as
Related Coatings, Materials, and Applications and is the direct responsibility of
agreed upon between the purchaser and seller.
Subcommittee D01.46 on Industrial Protective Coatings.
Current edition approved Dec. 1, 2014. Published January 2015. Originally
approved in 2004. Last previous edition approved in 2009 as D7055 – 09. DOI:
10.1520/D7055-14.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American National Standards Institute (ANSI), 25 W. 43rd St.,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,
the ASTM website. Pittsburgh, PA 15222-4656, http://www.sspc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7055 − 14
5.3 The steel composition shall be either Specifications 6.4 Select the Abrasive Type—Select the abrasive type as
A36/A36M, A572/A572M, A1011/A1011M or as agreed upon defined below, or specify an alternative abrasive. The abrasive
5
between the purchaser and seller. size shall be determined by the surface profile range selected in
6.3. The actual size(s) used shall be reported. Mineral and slag
5.4 The surface condition of the steel prior to surface
abrasives shall meet the requirements of SSPC-AB-1; Steel
preparation shall be specified and shall be
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D7055 − 09 D7055 − 14
Standard Practice for
Preparation (by Abrasive Blast Cleaning) of Hot-Rolled
1
Carbon Steel Panels for Testing of Coatings
This standard is issued under the fixed designation D7055; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice covers the procedures to be followed in the preparation (by abrasive blast cleaning) of hot rolled steel panels
for laboratory testing of coatings.
1.2 This standard practice does not include procedures for the application of coatings.
1.3 The values stated in SIinch-pound units are to be regarded as the standard. The values given in parentheses are for
information only.mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A572/A572M Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-
Strength Low-Alloy with Improved Formability, and Ultra-High Strength
D4285 Test Method for Indicating Oil or Water in Compressed Air
D4417 Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
D4940 Test Method for Conductimetric Analysis of Water Soluble Ionic Contamination of Blasting Abrasives
D7393 Practice for Indicating Oil in Abrasives
2.2 ISO Standard:
3
ISO 8502-3, Part 3 Assessment of Dust on Steel Surfaces Prepared for Painting (pressure-sensitive tape method)
4
2.3 SSPC/NACE Standards:
AB-1 Mineral and Slag Abrasives
AB-2 Specification for Cleanliness of Recycled Ferrous Metallic Abrasives
AB-3 Newly Manufactured or Re-Manufactured Steel Abrasives
SP1SP 1 Solvent Cleaning
SP5/NACE SP 5/NACE No. 1 White Metal Blast Cleaning
SP 6/NACE No. 3 Commercial Blast Cleaning
SP10/NACE SP 10/NACE No. 2 Near-White Metal Blast Cleaning
SSPC-VIS 1 Guide and Reference Photographs for Steel Surfaces Prepared by Dry Abrasive Blast Cleaning
3. Summary of Practice
3.1 This practice enables the user to specify the level of preparation of hot-rolled carbon steel test panels (prepared by dry
abrasive blast cleaning) for testing of coatings, including the steel composition, the degree of surface cleanliness, and the type of
abrasive.
1
This practice is under the jurisdiction of ASTM Committee D01 on Paint and Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.46 on Industrial Protective Coatings.
Current edition approved Dec. 1, 2009Dec. 1, 2014. Published January 2010January 2015. Originally approved in 2004. Last previous edition approved in 20042009 as
D7055 - 04.D7055 – 09. DOI: 10.1520/D7055-09.10.1520/D7055-14.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’sstandard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
4
Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor, Pittsburgh, PA 15222-4656, http://www.sspc.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D7055 − 14
4. Significance and Use
4.1 The procedures described in this practice are designed to provide hot-rolled, carbon steel panels with uniform and
reproducible abrasive blast cleaned surfaces for testing of coatings.
5. Test Panels
5.1 Prepare the test panels from unpainted hot-rolled steel plate or bar stock.
5.2 Prepare the test panels from unpainted hot-rolled steel plate or bar stock as described in 5.2 and 5.3. The panels shall be
made to a size and thickness as agreed upon between the purchaser and seller.
5.3 The steel compositio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.